T-REX-XP Posted August 19, 2021 Share #576 Posted August 19, 2021 @ThorGroup, is it possible to map internal ssd as hdd, that is available for installer? There are a lot of single board pc with embedded ssd. It will be a good chance use them as energy efficiency solutions or portable nas. I have one os them, so I can provide any logs, etc... Thanks. Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 19, 2021 Share #577 Posted August 19, 2021 1 minute ago, T-REX-XP said: @ThorGroup, is it possible to map internal ssd as hdd, that is available for installer? There are a lot of single board pc with embedded ssd. It will be a good chance use them as energy efficiency solutions or portable nas. I have one os them, so I can provide any logs, etc... Thanks. With proxmox you can do that install in it and give require space as SATA0 drive Link to comment Share on other sites More sharing options...
T-REX-XP Posted August 19, 2021 Share #578 Posted August 19, 2021 Just now, psychoboi32 said: With proxmox you can do that install in it and give require space as SATA0 drive Is a pretty limited by resources hw. With intel atom and 2gigs of ram. So I'm not sure that the proxmox or esxi will be best approach for it. Link to comment Share on other sites More sharing options...
T-REX-XP Posted August 19, 2021 Share #579 Posted August 19, 2021 Just now, T-REX-XP said: Is a pretty limited by resources hw. With intel atom and 2gigs of ram. So I'm not sure that the proxmox or esxi will be best approach for it. For example, atomic pi, latte panda, chuwi larchbox, etc... no name intel based pc from aliexpress. Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 19, 2021 Share #580 Posted August 19, 2021 (edited) 5 minutes ago, T-REX-XP said: Is a pretty limited by resources hw. With intel atom and 2gigs of ram. So I'm not sure that the proxmox or esxi will be best approach for it. can you not increase ram of it? if not my idea use linux and make that drive as ISCSI so I can connect that storage local that I will do a persistence USB bootable disk with linux and make that whole storage as Iscsi. use persistence USB install cockpit on it and see magic Edited August 19, 2021 by psychoboi32 Link to comment Share on other sites More sharing options...
T-REX-XP Posted August 19, 2021 Share #581 Posted August 19, 2021 (edited) 3 minutes ago, psychoboi32 said: can you not increase ram of it? if not my idea use linux and make that drive as ISCSI so I can connect that storage local that I will do No, I can't do it. is not standalone mb. All components embedded to motherboard via soldering. Its compact and low energy consuming solution, such as raspberry pi. Edited August 19, 2021 by T-REX-XP Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 19, 2021 Share #582 Posted August 19, 2021 (edited) 5 minutes ago, T-REX-XP said: No, I can't do it. is not standalone mb. All components embedded to motherboard via soldering. Its compact and low energy consuming solution, such as raspberry pi. Understood it is x86-64 board just like Pi, see above mention use base linux with cockpit and share that volume as iscsi but yes your data in raid 0. if may I suggest you lets open another thread where we can discuss or send me PM right away hope I can help Edited August 19, 2021 by psychoboi32 1 Link to comment Share on other sites More sharing options...
loomes Posted August 19, 2021 Share #583 Posted August 19, 2021 1 hour ago, ilovepancakes said: OK cool. Did that log you posted above showing the face detection plugin failing come from /var/log/messages or another log? This is the synofoto.log in /var/logs Link to comment Share on other sites More sharing options...
ilovepancakes Posted August 19, 2021 Share #584 Posted August 19, 2021 1 minute ago, loomes said: This is the synofoto.log in /var/logs Does /var/log/messages show anything related to face detection or Photos? Link to comment Share on other sites More sharing options...
Orphée Posted August 19, 2021 Share #585 Posted August 19, 2021 5 hours ago, ThorGroup said: It looks like your image or storage is damaged somehow. If you look into the log there are ext driver errors saying it cannot save blocks to disk. We would look into ESXi logs. If there isn't anything interesting there try to transfer the image again. We saw this before on Proxmox when the image was replaced when machine was still running, but this is quite unusual and we don't think you did that here I'm using the following VMDK file (the one from Jun's loader) to load synoboot.img : # Disk DescriptorFile version=1 CID=9fb45bdb parentCID=ffffffff createType="vmfs" # Extent description RW 102400 VMFS "synoboot.img" # The Disk Data Base #DDB ddb.adapterType = "lsilogic" ddb.deletable = "true" ddb.encoding = "UTF-8" ddb.longContentID = "cd061c7d6828764fa3d6bf989fb45bdb" ddb.thinProvisioned = "1" ddb.toolsInstallType = "0" ddb.toolsVersion = "2147483647" ddb.uuid = "60 00 C2 9a ee da ca 33-df 5e 04 3f 80 55 f9 62" ddb.virtualHWVersion = "10" @scoobdriver was right, I just needed to add following args (extracted from jun's loader grub.cfg file) : sata_uid=1 sata_pcislot=5 DiskIdxMap=0C SataPortMap=1 SasIdxMap=0 to make SATA1 available in VMWare configuration, it should make LSI passtrough work (just a guess, did not try yet on my production env) @psychoboi32 (try at your own risk) My current VM settings are : @ThorGroup I'm using same SSD as pool storage for data disk. I created a 40GB virtual disk exactly the same way as I did for Jun's loader, or that I usually do for other VM likes Ubuntu currently used to build loader with docker. I build the loader from a Ubuntu's VM running on the same SSD where my Xpenology PROD (jun's) is running. So I really don't think it can be a failure from SSD pool storage... I also tried to create a 50GB virtual disk on my real NAS pool storage, same result. 21.log 23.log 2 Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 20, 2021 Share #586 Posted August 20, 2021 I just notice I can only boot redpill if I use legacy bios but for apollolake xpenlogy it was recommended to use UEFI, hmm can we resolve some errors by that idk but we can try. Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 20, 2021 Share #587 Posted August 20, 2021 (edited) 5 hours ago, Orphée said: sata_uid=1 sata_pcislot=5 DiskIdxMap=0C SataPortMap=1 SasIdxMap=0 where should I add this? means in grub.cfg or .vmx can you help me with that got my answer it should be added in grub.cfg thanks I want to DSM7 ui on xpenology and data already backup (hyperbackup) don't worry Edited August 20, 2021 by psychoboi32 Link to comment Share on other sites More sharing options...
Balrog Posted August 20, 2021 Share #588 Posted August 20, 2021 I am currently not able to build the Apollolake 7.0 image for #41890: ... > [stage-1 3/9] RUN git clone https://github.com/RedPill-TTG/redpill-lkm.git -b master /opt/redpill-lkm && git clone https://github.com/jumkey/redpill-load.git -b 7.0-41890 /opt/redpill-load: #6 0.438 Cloning into '/opt/redpill-lkm'... #6 1.081 Cloning into '/opt/redpill-load'... #6 1.426 fatal: Remote branch 7.0-41890 not found in upstream origin ------ executor failed running [/bin/sh -c git clone ${REDPILL_LKM_REPO} -b ${REDPILL_LKM_BRANCH} ${REDPILL_LKM_SRC} && git clone ${REDPILL_LOAD_REPO} -b ${REDPILL_LOAD_BRANCH} ${REDPILL_LOAD_SRC}]: exit code: 128 Is the remote branch for 7.0-41890 deactivated and I have missed this? Link to comment Share on other sites More sharing options...
jumkey Posted August 20, 2021 Share #589 Posted August 20, 2021 (edited) 6 minutes ago, Balrog said: I am currently not able to build the Apollolake 7.0 image for #41890: ... > [stage-1 3/9] RUN git clone https://github.com/RedPill-TTG/redpill-lkm.git -b master /opt/redpill-lkm && git clone https://github.com/jumkey/redpill-load.git -b 7.0-41890 /opt/redpill-load: #6 0.438 Cloning into '/opt/redpill-lkm'... #6 1.081 Cloning into '/opt/redpill-load'... #6 1.426 fatal: Remote branch 7.0-41890 not found in upstream origin ------ executor failed running [/bin/sh -c git clone ${REDPILL_LKM_REPO} -b ${REDPILL_LKM_BRANCH} ${REDPILL_LKM_SRC} && git clone ${REDPILL_LOAD_REPO} -b ${REDPILL_LOAD_BRANCH} ${REDPILL_LOAD_SRC}]: exit code: 128 Is the remote branch for 7.0-41890 deactivated and I have missed this? sorry this branch has merged into master and deleted😅 Edited August 20, 2021 by jumkey Link to comment Share on other sites More sharing options...
plegs Posted August 20, 2021 Share #590 Posted August 20, 2021 7 minutes ago, Balrog said: Is the remote branch for 7.0-41890 deactivated and I have missed this? can't confirm. working fine for me. just run ist again. 1 Link to comment Share on other sites More sharing options...
haydibe Posted August 20, 2021 Share #591 Posted August 20, 2021 17 minutes ago, Balrog said: am currently not able to build the Apollolake 7.0 image for #41890: ... > [stage-1 3/9] RUN git clone https://github.com/RedPill-TTG/redpill-lkm.git -b master /opt/redpill-lkm && git clone https://github.com/jumkey/redpill-load.git -b 7.0-41890 /opt/redpill-load: #6 0.438 Cloning into '/opt/redpill-lkm'... #6 1.081 Cloning into '/opt/redpill-load'... #6 1.426 fatal: Remote branch 7.0-41890 not found in upstream origin ------ executor failed running [/bin/sh -c git clone ${REDPILL_LKM_REPO} -b ${REDPILL_LKM_BRANCH} ${REDPILL_LKM_SRC} && git clone ${REDPILL_LOAD_REPO} -b ${REDPILL_LOAD_BRANCH} ${REDPILL_LOAD_SRC}]: exit code: 128 Is the remote branch for 7.0-41890 deactivated and I have missed this? You need to use v0.5.4 of the script OR just change the url and branch in the global_settings.json. Just copy the values for load repo from one of the other profiles. 1 Link to comment Share on other sites More sharing options...
haydibe Posted August 20, 2021 Share #592 Posted August 20, 2021 (edited) 13 hours ago, psychoboi32 said: it is easy if you need my config i can share with you boot: order=usb0 cores: 4 cpu: SandyBridge hostpci0: 0000:01:00 hostpci1: 0000:08:00 memory: 8192 name: XPenology-TMP-ds918 net1: e1000=8A:C1:48:E3:A6:4D,bridge=vmbr0 numa: 0 ostype: l26 sata0: local-lvm:vm-102-disk-2,size=32G scsihw: virtio-scsi-pci serial0: socket smbios1: uuid=04F674CF-F8B7-4268-998C-629149B97412 sockets: 1 tablet: 0 usb0: host=090c:1000,usb3=1 vga: serial0 just make vm and put this config change pcie card according that if you need any help how to passthrough i have written guide i can share with you there was backup of proxmox available on this forum just use that and remove jun loader files and put redpill there as you can see my vm name it is used from that 😛 You are right, wasn't that hard after all. I have noticed the backup, but honestly don't like the idea of restoring someone elses backup. At the end it was as easy as adding a virtio network card, the usb controller and serial0 port, and manualy edit the vm's conf to add: args: -device 'qemu-xhci,addr=0x18' -drive 'id=synoboot,file=/var/lib/vz/images/XXX/redpill-DS918+_7.0-41890.img,if=none,format=raw' -device 'usb-storage,id=synoboot,drive=synoboot,bootindex=5' at the top of the vm config file: /etc/pve/nodes/zzz/qemu-server/xxx.conf Then used this user_config.json: { "extra_cmdline": { "pid": "0x0001", "vid": "0x46f4", "sn": "xxxxxxxx", "mac1": "xxxxxxxxxxx" }, "synoinfo": {}, "ramdisk_copy": {} } } Of course with a generated sn and mac1. What should I say: Successfully migrated one of my old XPE vm's from ESXi to Proxmox. I do favor the usb bootdrive approach over the sata_dom boot approach. For me that's the way to go, unless ThorGroup argues in one of their fabulous explainations why it's better to use sata_dom instead Edited August 20, 2021 by haydibe 2 1 Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 20, 2021 Share #593 Posted August 20, 2021 (edited) 15 minutes ago, haydibe said: You are right, wasn't that hard after all. I have noticed the backup, but honestly don't like the idea of restoring someone elses backup. At the end it was as easy as adding a virtio network card, the usb controller and serial0 port, and manualy edit the vm's conf to add: args: -device 'qemu-xhci,addr=0x18' -drive 'id=synoboot,file=/var/lib/vz/images/XXX/redpill-DS918+_7.0-41890.img,if=none,format=raw' -device 'usb-storage,id=synoboot,drive=synoboot,bootindex=5' at the top of the vm config file: /etc/pve/nodes/zzz/qemu-server/xxx.conf Then used this user_config.json: { "extra_cmdline": { "pid": "0x0001", "vid": "0x46f4", "sn": "xxxxxxxx", "mac1": "xxxxxxxxxxx" }, "synoinfo": {}, "ramdisk_copy": {} } } Of course with a generated sn and mac1. What should I say: Successfully migrated one of my old XPE vm's from ESXi to Proxmox. I do favor the usb bootdrive approach over the sata_dom boot approach. For me that's the way to go, unless ThorGroup argues in one of their fabulous explainations why it's better to use sata_dom instead thank you for clearing my doubt but i am stuck with mpt3sas driver do you have any idea how to resolve. if docker run there are some virtio driver i saw can i add mpt3sas there thank you so much for args for pcie passthrough if you need help i have some guides or scripts or command whatever you call english not my forte for current here is sneak peak do you hate proxmox message when you login , you can't get apt update here is a solution # Disable Commercial Repo sed -i "s/^deb/\#deb/" /etc/apt/sources.list.d/pve-enterprise.list apt-get update # Add PVE Community Repo echo "deb http://download.proxmox.com/debian/pve $(grep "VERSION=" /etc/os-release | sed -n 's/.*(\(.*\)).*/\1/p') pve-no-subscription" > /etc/apt/sources.list.d/pve-no-enterprise.list apt-get update # Remove nag echo "DPkg::Post-Invoke { \"dpkg -V proxmox-widget-toolkit | grep -q '/proxmoxlib\.js$'; if [ \$? -eq 1 ]; then { echo 'Removing subscription nag from UI...'; sed -i '/data.status/{s/\!//;s/Active/NoMoreNagging/}' /usr/share/javascript/proxmox-widget-toolkit/proxmoxlib.js; }; fi\"; };" > /etc/apt/apt.conf.d/no-nag-script apt --reinstall install proxmox-widget-toolkit Edited August 20, 2021 by psychoboi32 1 Link to comment Share on other sites More sharing options...
Orphée Posted August 20, 2021 Share #594 Posted August 20, 2021 3 hours ago, psychoboi32 said: where should I add this? means in grub.cfg or .vmx can you help me with that got my answer it should be added in grub.cfg thanks I want to DSM7 ui on xpenology and data already backup (hyperbackup) don't worry Inside the user_config.json { "extra_cmdline": { "vid": "0x058f", "pid": "0x6387", "sn": "1XXXXXXXXX9", "mac1": "001132XXXXXX", "sata_uid": "1", "sata_pcislot": "5", "DiskIdxMap": "0C", "SataPortMap": "1", "SasIdxMap": "0" }, "synoinfo": {}, "ramdisk_copy": {} } 1 1 Link to comment Share on other sites More sharing options...
T-REX-XP Posted August 20, 2021 Share #595 Posted August 20, 2021 13 hours ago, T-REX-XP said: @ThorGroup, is it possible to map internal ssd as hdd, that is available for installer? There are a lot of single board pc with embedded ssd. It will be a good chance use them as energy efficiency solutions or portable nas. I have one os them, so I can provide any logs, etc... Thanks. @ThorGroup,From the device perspective it look like this: MMC/SD card mmcblk0 device. Thanks in advance. Link to comment Share on other sites More sharing options...
scoobdriver Posted August 20, 2021 Share #596 Posted August 20, 2021 @haydibe Thanks for your work . Could you advise how I "Clean up" the docker tool . I'm running this on a small VM , it works great first time , but if I try to generate a new image , I'm out of disk space (seems to grow every time I generate and image for the same Architecture) . without removing everything and starting again , are there any locations I can remove files ? Link to comment Share on other sites More sharing options...
mcdull Posted August 20, 2021 Share #597 Posted August 20, 2021 (edited) 18 minutes ago, scoobdriver said: @haydibe Thanks for your work . Could you advise how I "Clean up" the docker tool . I'm running this on a small VM , it works great first time , but if I try to generate a new image , I'm out of disk space (seems to grow every time I generate and image for the same Architecture) . without removing everything and starting again , are there any locations I can remove files ? In general it should clear up by itself under /opt And ./images that it will store the final img file. You may refer to these locations. (I uses dockerce only) to me I would rather make a snapshot and revert it when necessary. Edited August 20, 2021 by mcdull Link to comment Share on other sites More sharing options...
gadreel Posted August 20, 2021 Share #598 Posted August 20, 2021 15 minutes ago, scoobdriver said: @haydibe Thanks for your work . Could you advise how I "Clean up" the docker tool . I'm running this on a small VM , it works great first time , but if I try to generate a new image , I'm out of disk space (seems to grow every time I generate and image for the same Architecture) . without removing everything and starting again , are there any locations I can remove files ? I want to know about this too. 30GB pop os gone in a few days... Link to comment Share on other sites More sharing options...
Orphée Posted August 20, 2021 Share #599 Posted August 20, 2021 # docker system prune -a WARNING! This will remove: - all stopped containers - all networks not used by at least one container - all images without at least one container associated to them - all build cache Are you sure you want to continue? [y/N] y Deleted Containers: bee0d8988fb7b942a53d2317808b96cec9e9e17496f869f2ea9021f01d0567f6 Deleted Images: untagged: redpill-tool-chain:bromolow deleted: sha256:5d92e907c8a059bc035a5d8753cb8e0673d51975914cab6deac1f120d0084c79 deleted: sha256:93f68868a99acf5fcede3c392412fa989d0c47cb5fe4899a05487bbf8b6e0e47 untagged: hello-world:latest untagged: hello-world@sha256:df5f5184104426b65967e016ff2ac0bfcd44ad7899ca3bbcf8e44e4461491a9e deleted: sha256:d1165f2212346b2bab48cb01c1e39ee8ad1be46b87873d9ca7a4e434980a7726 deleted: sha256:f22b99068db93900abe17f7f5e09ec775c2826ecfe9db961fea68293744144bd deleted: sha256:e1540cbeb3186a2f7eb8b7ded1384ba44255513b2755788e6da07518c3b34f70 untagged: redpill-tool-chain:bromolow-6.2.4-25556 deleted: sha256:59b6a6144bf160bc0012882ada0b574df2833a86834d7223a59d38b4be530861 deleted: sha256:3c8dd3d9c68a2cece7f7561d8300ab81e761f9c8d6b98444391507abf8afbd30 Deleted build cache objects: uumdb3voglmmz4yhlsb11e85y kl4c4j9qyu389a82b76y54m3e lwy4ik8szojsd0wngqd4wge66 6yzpusf4c8aasj0dcp2s0t9go qrbzqwxdkzyr7l6mvbao14ips oomjhhzk50mgiovrmshm47b9k ih9zgrnxd0qoosnegoh0w1krs vy8thfkw6aw3wql77hx9kcbnl nkk8mt9k3e4gs9a2eegdl3hii 58jrha6epn6p43y7d6mke3zns amalxlohyde2slhy6un7i6g5s zi672ioptqy9uri82a9vrj4hm 3s1k430445qlffpdcc7efby1o yticmw3v7mtbxddq4ujoaazxk j3snfib3r72ut53em2ezrbtop p2abem0ow082vw8kx4jrmxqi8 vmnaixl06w5h42s7z9cbtutug vvigozr3wgpmpcfcvlvgw4zcu 6c6e1s694qjsfwny33x5sjt3x qwr82bhsc92ngu1i1bwjtbygj mnflafwcrievgegdp1unuxpga 38bn8zirvuw933unt71drc5fb van3nd9uvdc3j928pukn78jg7 wqsk1yii7billcp6fkzii9b2v jfyf8l67t929fyxw2qlgrvqh9 dosulellulc65777kbs6ie9lc 99prlk0m201ij3q3oa1sch5ip xw2a0yg917b8l2lgdrk4671ic xg7mp0uwytup59o657pqzr0e8 wabqmd9l4xnnqpnryxgw7mng1 l0fi8x2ldu0v63ajnwgy2epcz cer3qvy3gn4vwsw7z16xr06ee v0o5w4hu1uuw9la1enabzl8rd nlhmju9fk92ursmjn5vv3zel7 p460jyfctzyoxj4tp5d0n2on0 t6axr2h56dgo4engjlqu52qfp kvqvfqgziogwg9mtkvajv0e1w r0h1wlhz73obe6uot3gxqfuzq 1am0833fne0vwn63a6n1h2b9u idi1mdsg5qe8fkaiwczjjoh4g qeav24lqyyrt0o19mizikuavl j7e2o0gxb7sq1m75grulqh8xc sne2h33ykcw3bcenggwyffhe4 6maze4683rv30dptq7kdbvums hce36etohn2ta7tk50pu0nlg8 j140fnypn3ddv6gb45pdd60ev s1ho43cfumltpt3tsy7kforhm wnwcs4cagynoqfrurkezw5poj Total reclaimed space: 6.054GB root@ubuntu:/home/orphee/Downloads/redpill/images# BE CAREFULL WITH THIS COMMAND, IT WILL DELETE EVERYTHING CONSIDERED AS NOT USED. If you are unsure, avoid it. If you use docker only for redpill, you can do it safely. But next time you run it, it will have to redownload everything needed. 3 Link to comment Share on other sites More sharing options...
psychoboi32 Posted August 20, 2021 Share #600 Posted August 20, 2021 (edited) ./caches have .pat files ./images have all images you built if you remove other things than it will not work after that Edited August 20, 2021 by psychoboi32 Link to comment Share on other sites More sharing options...
Recommended Posts