cospotato Posted February 19, 2022 Share #1051 Posted February 19, 2022 5 hours ago, pocopico said: At that time a change at tty console happens . You should have something after that just let it go it will continue after a minute. But i wait for half an hours. Nothing happened😂 Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted February 19, 2022 Share #1052 Posted February 19, 2022 16 hours ago, danellis12561 said: Actually, I removed the storage pool I created and the RAM stopped creeping up. I rebooted and created the SHR pool with one drive which completed without issue. I'm adding a second drive right now and the RAM is staying at 1%. If it finishes adding the second drive with no issues, I'll add the other two and monitor it. Maybe something with the initial creation of the SHR pool of 4 disks was wonky. There was a similar phenomenon in my DS3622xs+ SHR. SHR was first configured with four SATA HDD. Unexpectedly, I needed a day of restructuring. My 8GB of RAM was using almost 95% of the resources. So, I deleted the storage pool and volume and made SHR again with only one disk, and did not attempt to reconstruct it. If there is another attempt to reconstruct with two or more disks and another lack of RAM resources occurs, it plans to report it to @pocopico Quote Link to comment Share on other sites More sharing options...
Orphée Posted February 19, 2022 Share #1053 Posted February 19, 2022 Just my 2 cents, you should avoid SHR and stick to RAID (5)... easier to manage, and not synology dependent... 1 Quote Link to comment Share on other sites More sharing options...
danellis12561 Posted February 19, 2022 Share #1054 Posted February 19, 2022 2 hours ago, Peter Suh said: There was a similar phenomenon in my DS3622xs+ SHR. SHR was first configured with four SATA HDD. Unexpectedly, I needed a day of restructuring. My 8GB of RAM was using almost 95% of the resources. So, I deleted the storage pool and volume and made SHR again with only one disk, and did not attempt to reconstruct it. If there is another attempt to reconstruct with two or more disks and another lack of RAM resources occurs, it plans to report it to @pocopico Similar here. I rebuilt the SHR with a single disk, which was fine. I added another single drive to the SHR and there were no issues. I tried adding 2 more disks simultaneously and ran into the RAM issue. It reboots before the expansion completes and just goes int a loop trying to expand the SHR. I imagine that if I were to keep adding a single drive at a time it would be fine. But adding multiple drives at once seems to cause the RAM issues. @Peter Suh what kind of hardware are you installing on? @pocopicoIs there something we can do to help figure out what's going on? Quote Link to comment Share on other sites More sharing options...
pocopico Posted February 19, 2022 Author Share #1055 Posted February 19, 2022 3 hours ago, cospotato said: But i wait for half an hours. Nothing happened😂 :D:D:D ok ... so nothing will happen ... did you switch to com1 ? Quote Link to comment Share on other sites More sharing options...
ilovepancakes Posted February 19, 2022 Share #1056 Posted February 19, 2022 This page seems to have gone live recently but the download links don't work for me. https://prerelease.synology.com/en-global/download/dsm71_beta Anyone happen to have them work and try out if v7.1 is an easy update for Redpill/Tinycore to handle? Quote Link to comment Share on other sites More sharing options...
maxime Posted February 19, 2022 Share #1057 Posted February 19, 2022 I'm having this problem: I tried many version (DS3615xs, DS918+, DS3622xs+) but the problem is always the same! Mainboard is a Gigabyte H97M-D3H. Any suggestion, please? Quote Link to comment Share on other sites More sharing options...
maxime Posted February 19, 2022 Share #1058 Posted February 19, 2022 Can the bootloader run from a SD card? When I run ./rploader.sh identifyusb now, system can't find vid and pid of the SD I'm booting from 🤔 Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted February 19, 2022 Share #1059 Posted February 19, 2022 6 hours ago, danellis12561 said: Similar here. I rebuilt the SHR with a single disk, which was fine. I added another single drive to the SHR and there were no issues. I tried adding 2 more disks simultaneously and ran into the RAM issue. It reboots before the expansion completes and just goes int a loop trying to expand the SHR. I imagine that if I were to keep adding a single drive at a time it would be fine. But adding multiple drives at once seems to cause the RAM issues. @Peter Suh what kind of hardware are you installing on? @pocopicoIs there something we can do to help figure out what's going on? The first shr-generated multi-disk combination I tried was a test of 0.6 TB + 2 TB + 2 TB + 3 TB. After the RAM issue occurred, the storage pool and volume were deleted, and abnormal restart occurred in this process. Since this restart, the storage pool has been deleted and there have been no other errors. I don't know if I know exactly, but the mpt3sas driver seems to have been updated from version 22 to 41, so I'm rebuilding the loader and watching for 18 hours after creating it with SHR 2TB+ 2TB+3TB. No other abnormal symptoms have been seen yet. Quote Link to comment Share on other sites More sharing options...
altas Posted February 19, 2022 Share #1060 Posted February 19, 2022 Can the bootloader run from a SD card? When I run ./rploader.sh identifyusb now, system can't find vid and pid of the SD I'm booting from [emoji848]Use USB or Sata (esxi) Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted February 19, 2022 Share #1061 Posted February 19, 2022 6 minutes ago, Peter Suh said: The first shr-generated multi-disk combination I tried was a test of 0.6 TB + 2 TB + 2 TB + 3 TB. After the RAM issue occurred, the storage pool and volume were deleted, and abnormal restart occurred in this process. Since this restart, the storage pool has been deleted and there have been no other errors. I don't know if I know exactly, but the mpt3sas driver seems to have been updated from version 22 to 41, so I'm rebuilding the loader and watching for 18 hours after creating it with SHR 2TB+ 2TB+3TB. No other abnormal symptoms have been seen yet. this is my pc. CPU : i3-4160T M/B : DT-H81DL GAIDA LAN : RealTek r8111F DUAL RAID : Dell Perc H310 , IT Mode LOADER : Tinycore 0.4.5 Native EXT : r8169, mpt3sas DSM : DS3622xs+ 7.0.1 HDD : 4ea Sata Drives Quote Link to comment Share on other sites More sharing options...
maxime Posted February 19, 2022 Share #1062 Posted February 19, 2022 Just now, altas said: Use USB or Sata (esxi) I know it. SD Card reader is USB and perfectly works on Jun bootloader. I would like use it on redpill loader Quote Link to comment Share on other sites More sharing options...
altas Posted February 19, 2022 Share #1063 Posted February 19, 2022 Then use the same vid/pid But i am not sure if already one was successfully with SD Card boot 1 Quote Link to comment Share on other sites More sharing options...
danellis12561 Posted February 20, 2022 Share #1064 Posted February 20, 2022 1 hour ago, Peter Suh said: this is my pc. CPU : i3-4160T M/B : DT-H81DL GAIDA LAN : RealTek r8111F DUAL RAID : Dell Perc H310 , IT Mode LOADER : Tinycore 0.4.5 Native EXT : r8169, mpt3sas DSM : DS3622xs+ 7.0.1 HDD : 4ea Sata Drives Did you add the mpt3sas driver manually? If so, that might not be it as I have not added any extra modules. It was just the basic TC loader setup. Also, did you flash the h310 to IT mode, or did it you get it already flashed? Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted February 20, 2022 Share #1065 Posted February 20, 2022 1 hour ago, danellis12561 said: Did you add the mpt3sas driver manually? If so, that might not be it as I have not added any extra modules. It was just the basic TC loader setup. Also, did you flash the h310 to IT mode, or did it you get it already flashed? The mpt3sas driver was not added manually. Drivers automatically added during the build process were used. I flash the H310 to IT Mode myself, what is the problem here? This PC specification is already stably used for Jun loader 1.04b DSM 6.2.3. Quote Link to comment Share on other sites More sharing options...
danellis12561 Posted February 20, 2022 Share #1066 Posted February 20, 2022 6 minutes ago, Peter Suh said: The mpt3sas driver was not added manually. Drivers automatically added during the build process were used. I flash the H310 to IT Mode myself, what is the problem here? This PC specification is already stably used for Jun loader 1.04b DSM 6.2.3. Okay. I wasn't sure if it was something that was manually added and I know I didn't add anything extra to mine. I just wanted to make sure we were comparing apples to apples. I flashed my card as well (h710) and have seen some people on here mentioning ordering cards that are already flashed since theirs weren't flashed to IT mode. It was pretty easy to flash mine, so I was just curious. Are you still having issues after the mpt3sas driver update? It seems to be okay if I only add one disk at a time, but that can be time consuming. Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted February 20, 2022 Share #1067 Posted February 20, 2022 (edited) 13 minutes ago, danellis12561 said: Okay. I wasn't sure if it was something that was manually added and I know I didn't add anything extra to mine. I just wanted to make sure we were comparing apples to apples. I flashed my card as well (h710) and have seen some people on here mentioning ordering cards that are already flashed since theirs weren't flashed to IT mode. It was pretty easy to flash mine, so I was just curious. Are you still having issues after the mpt3sas driver update? It seems to be okay if I only add one disk at a time, but that can be time consuming. I'm sure some of you already know, For repeated SHR or RAID volume configuration tests, Share tips on stopping volume optimization. SSH> sudo -i cat /proc/mdstat (Checking the disk number for optimization.) echo frozen > /sys/block/<md with number>/md/sync_action After this process, the storage pool and volume can be removed immediately. In the last RAM issue, symptoms were witnessed shortly after SHR optimization. SHR optimization will continue to try and report any problems. Edited February 20, 2022 by Peter Suh Quote Link to comment Share on other sites More sharing options...
pocopico Posted February 20, 2022 Author Share #1068 Posted February 20, 2022 12 hours ago, maxime said: I'm having this problem: I tried many version (DS3615xs, DS918+, DS3622xs+) but the problem is always the same! Mainboard is a Gigabyte H97M-D3H. Any suggestion, please? Its a typical SataPortMap and DiskIdxMap issue... Search the forum for that Quote Link to comment Share on other sites More sharing options...
Orphée Posted February 20, 2022 Share #1069 Posted February 20, 2022 For info. I built a fresh DS3615xs 6.2.4 VM to test how migration from 6.2.x DS3615xs to 7.0.1 DS3622xs+ is handled : It worked totally fine. Of course it is a clean fresh 6.2.4 install so it may not be so easy with lot of stuffs already installed. but I installed docker package on 6.2.4 before migration and it was updated fine on 7.0.1 install. Quote Link to comment Share on other sites More sharing options...
pocopico Posted February 20, 2022 Author Share #1070 Posted February 20, 2022 14 minutes ago, Orphée said: For info. I built a fresh DS3615xs 6.2.4 VM to test how migration from 6.2.x DS3615xs to 7.0.1 DS3622xs+ is handled : It worked totally fine. Of course it is a clean fresh 6.2.4 install so it may not be so easy with lot of stuffs already installed. but I installed docker package on 6.2.4 before migration and it was updated fine on 7.0.1 install. And is that on Gen8 ? Great news then .. 1 Quote Link to comment Share on other sites More sharing options...
Orphée Posted February 20, 2022 Share #1071 Posted February 20, 2022 Yep, ESXi Gen8. 1 Quote Link to comment Share on other sites More sharing options...
recoco Posted February 20, 2022 Share #1072 Posted February 20, 2022 tinycore-redpill.v0.4.5 with ext hpsa. The loader is built successfully without any error. But there is a error when booting. Quote ...... :: Loading module usb-storage[ 2.298664] usbcore: registered new interface driver usb-storage ... [ OK ] :: Loading kernel modules from extensions ... Loading kmod #0 "scsi_transport_sas.ko" for pocopico.hpsa (args: ) [ 2.308405] scsi_transport_sas: version magic '4.4.180+ SMP mod_unload ' should be '3.10.108 SMP mod_unload ' [ 2.309303] scsi_transport_sas: version magic '4.4.180+ SMP mod_unload ' should be '3.10.108 SMP mod_unload ' insmod: can't insert 'scsi_transport_sas.ko': invalid module format ERROR: kernel extensions "scsi_transport_sas.ko" from pocopico.hpsa failed to load Exit on error [99] rp ext init exec failure... Sun Feb 20 11:46:34 UTC 2022 none /sys/kernel/debug debugfs rw,relatime 0 0 [ 2.516065] usb 2-1: new high-speed USB device number 2 using ehci-pci ...... Quote Link to comment Share on other sites More sharing options...
pocopico Posted February 20, 2022 Author Share #1073 Posted February 20, 2022 (edited) 9 minutes ago, recoco said: tinycore-redpill.v0.4.5 with ext hpsa. The loader is built successfully without any error. But there is a error when booting. Is this for bromolow ? 3615xs ?? let me have a look Edit : yes it was pointing to wrong file .. i fixed that now i think Edited February 20, 2022 by pocopico Quote Link to comment Share on other sites More sharing options...
maxime Posted February 20, 2022 Share #1074 Posted February 20, 2022 8 hours ago, pocopico said: Its a typical SataPortMap and DiskIdxMap issue... Search the forum for that I can't find a solution... I can't understand the logic behind SataPortMap and DiskIdxMap values 😔 If anyone of you could give me an help, I would really appreciate it. Quote Link to comment Share on other sites More sharing options...
aportnov Posted February 20, 2022 Share #1075 Posted February 20, 2022 Hello everyone, I want to make a migration from 918 to 3622. I collect via tinycore, I do not specify the parameters of Sata Port Map and SasIdxMap, but they are written to the default config, if I remove them when booting, I still do not see the 11 -12 disk, although in the configuration only DiskIdxMap = 0004 on 918 everything works fine. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.