dimkov74 Posted March 28, 2017 Share #1001 Posted March 28, 2017 At 5.2, too, does not work. Sata drives are not visible. Link to comment Share on other sites More sharing options...
dimkov74 Posted March 28, 2017 Share #1002 Posted March 28, 2017 The HARDWARE SUPPORTED SHEET shows CCISS: Smart Array E200iBut it does not work on 6.1, can I enable this driver. This drivers list is for DSM 5.2 not for 6.1. At 5.2, too, does not work. Sata drives are not visible. Link to comment Share on other sites More sharing options...
sze Posted March 28, 2017 Share #1003 Posted March 28, 2017 Hi, see no Audio driver. Have here some DELL Optiplex 160 and want use the onboard audio chip to use it with squeezelite.I install squeezelite but it doesn't find any audio device. So I believe there is no audio driver included inside 6.0.2 for onborad chip. Can somebody told me if its possible to get a driver for this? Thanks Stefan Link to comment Share on other sites More sharing options...
alefello Posted March 29, 2017 Share #1004 Posted March 29, 2017 Hello I would like to install Xpenology on a Proxmox Virtual Environment and for best performance I would like to assign a phisical disks directly using VirtIO bus (which is paravirtualized). Virtio drivers are actually included as I can see the disk in /dev/vda but they're missing in DSM. I also tried to add them manually using synospace but without luck. Could you please update the drivers so VirtIO disks are usable? (I think XPenology only uses /dev/sdX disks) Or could someone please help me in having my VirtIO disk usable? Thank you Link to comment Share on other sites More sharing options...
Nybass2 Posted March 29, 2017 Share #1005 Posted March 29, 2017 I want to create my first own NAS and want to use the mainboard "ASRock J3455-ITX SoC". In the specification of the mainboard is written that this mainboard use "Realtek RTL8111GR" as lan driver. In the Hardware support list i found only "RTL8111G" without R. Can i use this mainboard or is it neccessary to find another one? Also I've seen that 2 SATA connectors goes directly to the CPU and the other 2 by "ASMedia ASM1061". Is this driver for the sata controller also supported? Thank you for your support. Link to comment Share on other sites More sharing options...
kilik Posted April 1, 2017 Share #1006 Posted April 1, 2017 LAN Realtek RTL8111H - 10/100/1000 Controller mainboard BIOSTARJ3160MD - Intel Celeron J3160. I've tested with dsm 6.0.2 but it hasn't passed ! Thanks ! Link to comment Share on other sites More sharing options...
OoERASERoO Posted April 1, 2017 Share #1007 Posted April 1, 2017 I need SCSI ---- Intel C600 Series Chipset SAS plz version: DSM 6.1 or 5.2 is ok Intel C600 Series Chipset SAS in synobios.ko is not working in dsm 5.2 too Do anyone have Intel synobios.ko v1/v2/v3 that have Intel C600 Series Chipset SAS driver? Link to comment Share on other sites More sharing options...
malo Posted April 3, 2017 Share #1008 Posted April 3, 2017 i210 driver please Link to comment Share on other sites More sharing options...
kaasic Posted April 3, 2017 Share #1009 Posted April 3, 2017 Is possible add VGA drivers like Intel HD Graphics? I need it to enable VGA Hardware Accelaration to transcode video. Link to comment Share on other sites More sharing options...
Kitaro Posted April 4, 2017 Share #1010 Posted April 4, 2017 i210 driver please i210 works perfectly. Watch my first configuration. Link to comment Share on other sites More sharing options...
jarzyn Posted April 8, 2017 Share #1011 Posted April 8, 2017 At first thank you for good job you are doing. Next I would like to ask you to add drivers for mainbord: Gigabyte GA-M61SME-S2L CPU: AMD Athlon 64 X2 Dual Core Processor 4200+ My setup start up, but I can not find it through find.synology. Network cable is supported as you mentioned in in supported hardware "forcedeth : nForce Ethernet". If there's something I'm missing i would be grateful for any guidance where to find answare to solve my problem. After weckend I will try to connect via com port so hope I will get some more logs and get to know what's going on. Link to comment Share on other sites More sharing options...
matyushkin Posted April 9, 2017 Share #1012 Posted April 9, 2017 Hi. My matherboad is ASRock A330ION http://asrock.com/mb/NVIDIA/A330ION/. On her eth driver is Nvidia forcedeth : nForce Ethernet. Please add this driver in loader for version 6.1. Thanks you. P.S. When will the stable loader for version 6.1 come out? Thanks for our work)))) Link to comment Share on other sites More sharing options...
mgrobins Posted April 10, 2017 Share #1013 Posted April 10, 2017 What do I need to provide for this to occur most easily? Supermicro and intel have Windows and Linux drivers for this motherboard. Driver request: Based on Supermicro X10SDV-4C-TLN2F https://www.supermicro.com/products/motherboard/Xeon/D/X10SDV-4C-TLN2F.cfm CPU and Chipset Drivers: Broadwell based SOC Intel® Xeon® processor D-1521 FCBGA 1667 NIC Driver Request: Intel® D-1500 SoC 10GbE Controller SoC 10GbE X552/X557-AT 10GBASE-T Latest intel Linux Driver: https://downloadcenter.intel.com/download/18700/Ethernet-Intel-Network-Adapter-Virtual-Function-Driver-for-Intel-10-Gigabit-Ethernet-Network-Connections ixgbe drivers .... not sure if these are useful for getting a driver that will work for a bare metal install (bit out of my depth with this stuff ). Ethernet Driver CD for windows, Linux and FreeBSD. https://downloadcenter.intel.com/download/22283/Ethernet-Intel-Ethernet-Adapter-Connections-CD?v=t ****************************************** EDIT: I can confirm the mainboard and NIC are operating on 6.1 update 2 (using jun's 1.02A loader with the 3615xs files not3617xs). The changes I had to make in 1.01 to get the NIC to function properly (relatingto the igbe driver interestingly even though the xgbe is for 10GBit?) are not required with the image structure in 1.02A EDIT 2: Now running 1.02-2A with the latest version of DSM and DS3617XS image and all appears to be detected and functioning as normal. I'd like to move some of this to the compatible hardware thread - do I just post and it gets folded into the overall thread? Link to comment Share on other sites More sharing options...
Unr3al2 Posted April 17, 2017 Share #1014 Posted April 17, 2017 Is possible add VGA drivers like Intel HD Graphics? I need it to enable VGA Hardware Accelaration to transcode video. Was it accelerated? Let me know how it will work. Link to comment Share on other sites More sharing options...
audiophile20 Posted April 18, 2017 Share #1015 Posted April 18, 2017 I have checked the Supported Devices list for 12G HBA card SAS Drivers and did not see these on the list. I am now running two builds with a 16x and 24x port SAS cards in two separate builds. I wcan use greatly appreciate the addition of the drivers. Please eat me know if that would be possible. Hopefully I did not make a mistake and duplicate the request. If this is a duplicate request, my apologies. Please do let me know. Thanks in advance for your asssitance. Oops! Details of build, one system running on DSM 5.2 and the other on DSM 6.1. Both are stable. CPU Xeon, mobo Supermicro X10 series, LSI SAS controller and Intel 5xx 10G copper. Link to comment Share on other sites More sharing options...
zaadstra Posted April 18, 2017 Share #1016 Posted April 18, 2017 Hi, I am running an AMD box with 780G chipset and SB700 southbridge. All appears to be working, drives are recognized and I have a working volume. So far so good. It is running XPEnology 5.2-5967 and DSM 5.2-5967-1. Directly installed, no ESX or HyperV. Mainboard Gigabyte GA-MA78GM-S2H. Only the SMART values are not read by DSM. I am especially missing the drive temperatures. Is this a setting or a driver issue? On the console of the pc, smartctl command reports drive serial but states that SMART is not enabled. Edit: I ran a Gparted live linux on this box and SMART was working fine. Smartctl returned correct smart values including drive temperature. Can this be fixed by inserting a (newer) .ko ? From Dmesg: [ 2.300410] ahci 0000:00:11.0: version 3.0 [ 2.300708] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 2.300712] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 2.331879] scsi0 : ahci [ 2.335894] scsi1 : ahci [ 2.338813] scsi2 : ahci [ 2.342621] scsi3 : ahci [ 2.346217] scsi4 : ahci [ 2.348225] scsi5 : ahci [ 2.351519] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22 [ 2.351526] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22 [ 2.351529] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22 [ 2.351533] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22 [ 2.351536] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f300 irq 22 [ 2.351539] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f380 irq 22 .. [ 2.966027] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ... [ 2.967768] ata1.00: ATA-8: Hitachi HUA722020ALA330, JKAOA25C, max UDMA/133 [ 2.967771] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA [ 2.969085] ata6.00: ATA-8: SAMSUNG HD501LJ, CR100-13, max UDMA7 [ 2.969087] ata6.00: 976771055 sectors, multi 0: LBA48 NCQ (depth 31/32), AA ... [ 2.969673] ata1.00: configured for UDMA/133 ... [ 2.971176] scsi 0:0:0:0: Direct-Access Hitachi HUA722020ALA330 JKAO PQ: 0 ANSI: 5 [ 2.972128] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 2.972204] sd 0:0:0:0: [sda] Write Protect is off [ 2.972208] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.972232] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FU From lsmod: ata_piix 24664 0 sata_uli 3004 0 sata_svw 4453 0 sata_qstor 5612 0 sata_sis 3884 0 pata_sis 10858 1 sata_sis stex 15005 0 sata_sx4 9284 0 sata_promise 10799 0 sata_nv 20623 0 sata_via 7803 0 sata_sil 7783 0 pata_amd 11054 0 pdc_adma 5868 0 pata_via 8827 0 pata_jmicron 2395 0 i did not do proper benchmarks, but transfers feel a bit slow... Thanks! Link to comment Share on other sites More sharing options...
b0g0m0l Posted April 27, 2017 Share #1017 Posted April 27, 2017 Add driver for Atheros ar8131. Thank you Link to comment Share on other sites More sharing options...
IG-88 Posted April 27, 2017 Share #1018 Posted April 27, 2017 Is possible add VGA drivers like Intel HD Graphics? I need it to enable VGA Hardware Accelaration to transcode video. Was it accelerated? Let me know how it will work. its about Intel® Quick Sync Video aka Intel QSV its mentioned here: https://xpenology.com/forum/viewtopic.php?f=2&t=32651 for usage of ffmpeg 2.8.0 and newer it needs something that synology dsm 6.0 does'nt support the coder of the serviio plugin explained it here https://pcloadletter.co.uk/2012/01/25/s ... o-package/ Link to comment Share on other sites More sharing options...
snoopy78 Posted May 3, 2017 Share #1019 Posted May 3, 2017 I have checked the Supported Devices list for 12G HBA card SAS Drivers and did not see these on the list. I am now running two builds with a 16x and 24x port SAS cards in two separate builds. I wcan use greatly appreciate the addition of the drivers. Please eat me know if that would be possible. Hopefully I did not make a mistake and duplicate the request. If this is a duplicate request, my apologies. Please do let me know. Thanks in advance for your asssitance. Oops! Details of build, one system running on DSM 5.2 and the other on DSM 6.1. Both are stable. CPU Xeon, mobo Supermicro X10 series, LSI SAS controller and Intel 5xx 10G copper. here a short DMESG output of my baremetal system running DSM 6.0 (previous 5.2) with following HW - SM X9 MoBo - Xeon E5 - 32GB RAM - LSI 9300-16i (16 Port 12G SAS3 HBA) - QLE 10G NIC 0.000000] DMI: Supermicro X9SRL-F/X9SRL-F, BIOS 3.2 01/16/2015 0.042034] smpboot: CPU0: Intel(R) Xeon(R) CPU E5-2603 v2 @ 1.80GHz (fam: 06, model: 3e, stepping: 04 5.556541] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) 5.561392] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) 5.575972] Fusion MPT base driver 3.04.20 5.748373] mpt3sas0: Allocated physical memory: size(16686 kB) 5.748377] mpt3sas0: Current Controller Queue Depth(9979),Max Controller Queue Depth(10240) 5.748378] mpt3sas0: Scatter Gather Elements per IO(128) 5.794182] mpt3sas0: LSISAS3008: FWVersion(11.00.00.00), ChipRevision(0x02), BiosVersion(08.27.00.00) 15.806292] qlcnic 0000:03:00.0: 2048KB memory map 16.284039] qlcnic 0000:03:00.0: Supports FW dump capability 16.284043] qlcnic 0000:03:00.0: Driver v5.2.42, firmware v4.14.26 16.298144] qlcnic: xx:xx:xx:xx:xx:xx: NC523SFP 10Gb 2-port Server Adapter Board Chip rev 0x54 so only your NIC is in question to work.. Link to comment Share on other sites More sharing options...
junho76 Posted May 7, 2017 Share #1020 Posted May 7, 2017 Could you make Reaktek 8111 ehternet driver for DSM 6.1? I'm using J3455 M/B... I tried to compile drivers myself...it's too complicated making develop environment Link to comment Share on other sites More sharing options...
NeoID Posted May 15, 2017 Share #1021 Posted May 15, 2017 I think there's something wrong with the current mpt2sas-driver. My card (SAS9201-16i) is supposed to be supported, but I get the following error right after boot finished: 2017-04-25T13:27:14-07:00 DiskStation root: == DSM 6.0 8451-0 finished boot up ==2017-04-25T13:27:14-07:00 DiskStation synoenc: enclosure_direct_host_model_id_get.c:38 Unknown SAS controller at host4, board name: SAS9201-16i 2017-04-25T13:27:14-07:00 DiskStation synoenc: enclosure_list_enum.c:190 failed to get enclosure head, please check enclosure firmware/hardware While I can see the drives in DSM (even the SN and temp), I get a lot of error in the logs like this: 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_parse_xml_kernel_err_ct.c:37 Error: /var/log/disk_overview.xml file not exist.2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_current_health_get.c:26 SYNODiskXmlErrCtGet failed on /dev/sda 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_is_below_life_thr.c:29 Failed to get health attribute 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_parse_xml_kernel_err_ct.c:37 Error: /var/log/disk_overview.xml file not exist. 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_current_health_get.c:26 SYNODiskXmlErrCtGet failed on /dev/sdb 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_is_below_life_thr.c:29 Failed to get health attribute 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: SmartDataRead(102) open device /dev/sdc fail 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_temperature_get.c:75 read value /dev/sdc fail 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: SmartFirmAndSerialRead(146) open device /dev/sdc fail 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_parse_xml_kernel_err_ct.c:33 Error: Failed to get firmware and SN of /dev/sdc 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_current_health_get.c:26 SYNODiskXmlErrCtGet failed on /dev/sdc 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_is_below_life_thr.c:29 Failed to get health attribute 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_parse_xml_kernel_err_ct.c:37 Error: /var/log/disk_overview.xml file not exist. 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_current_health_get.c:26 SYNODiskXmlErrCtGet failed on /dev/sdd 2017-04-25T22:28:15+02:00 moto SystemInfo.cgi: disk/disk_is_below_life_thr.c:29 Failed to get health attribute And as mentiond in other threads. Kernel panics if I try to turn on SNMP which only happens with this LSI card. Link to comment Share on other sites More sharing options...
thefrenchdexter Posted May 19, 2017 Share #1022 Posted May 19, 2017 Hello ! I'm using a MB Gigabyte EP45-DS3R (6 SATAII ports), a E8400 processor, 8GO of DDR2 ram and 2 x Realtek 8111C for the network wich is normally supported ... but i have this problem : When i tranfer files or folder int his way : PC==>NAS no problem, my speed i about 100 and 120 MO/s (really MO not Mb ) for big files of course ! When i tranfer files or folder int his way NAS==> PC ... the speed is about à 8MO/S, or 10 MO/s in the best case ! Do you think there is a problem with the driver ? A little more about my config : - My NAS is made with a MB Gigabyte EP45-DS3R (6 SATAII ports), a E8400 processor, 8GO of DDR2 ram and 2 x Realtek 8111C for the netwok - I have 5 HD in RAID SHR - The NAS have the DSM 6.0.2-8451 installed(but it was the same with DSM 5.2-5967) and XPEnoboot_DS3615 xs 6.0.2 Jun's Mod in a USB 2.0 32GO key - The ethernet port is in 1000Mbps full duplex. - The NAS and the PC are connected in the same switch SMC GS16 wich is in 1000 MBps - The PC is really fast : I7 4770K with 32 GO of memory and a Samsung 850 EVO SSD P.S : i've tested transfer with, FTP (Filezilla), windows explorer and Filestation and the result is the same P.S 2 : when i remove all the HD and install Win7 (instead of RAID5 + DSM)in a test HD, there is no problem, my speed is good (about 100Mo/s). P.S 3 : when i remove all the HD and install Xpenology (instead of RAID5 + DSM)in a test HD, the problem is the same Sorry for my poor english ... but i'm french and i've don't find an answer in the french section Link to comment Share on other sites More sharing options...
nunurs Posted May 20, 2017 Share #1023 Posted May 20, 2017 Hi, It's possible to add "Atheros PCI-E GbLAN controller AR8131M" please? Thx Link to comment Share on other sites More sharing options...
ordimans Posted May 21, 2017 Share #1024 Posted May 21, 2017 Hello ! I'm using a MB Gigabyte EP45-DS3R (6 SATAII ports), a E8400 processor, 8GO of DDR2 ram and 2 x Realtek 8111C for the network wich is normally supported ... but i have this problem : When i tranfer files or folder int his way : PC==>NAS no problem, my speed i about 100 and 120 MO/s (really MO not Mb ) for big files of course ! When i tranfer files or folder int his way NAS==> PC ... the speed is about à 8MO/S, or 10 MO/s in the best case ! Do you think there is a problem with the driver ? A little more about my config : - My NAS is made with a MB Gigabyte EP45-DS3R (6 SATAII ports), a E8400 processor, 8GO of DDR2 ram and 2 x Realtek 8111C for the netwok - I have 5 HD in RAID SHR - The NAS have the DSM 6.0.2-8451 installed(but it was the same with DSM 5.2-5967) and XPEnoboot_DS3615 xs 6.0.2 Jun's Mod in a USB 2.0 32GO key - The ethernet port is in 1000Mbps full duplex. - The NAS and the PC are connected in the same switch SMC GS16 wich is in 1000 MBps - The PC is really fast : I7 4770K with 32 GO of memory and a Samsung 850 EVO SSD P.S : i've tested transfer with, FTP (Filezilla), windows explorer and Filestation and the result is the same P.S 2 : when i remove all the HD and install Win7 (instead of RAID5 + DSM)in a test HD, there is no problem, my speed is good (about 100Mo/s). P.S 3 : when i remove all the HD and install Xpenology (instead of RAID5 + DSM)in a test HD, the problem is the same Sorry for my poor english ... but i'm french and i've don't find an answer in the french section Not sure.... I have a problem with Hyperbackup when i copy from DSM to another DSM. If i copy same file on NAs from PC, no problem... Link to comment Share on other sites More sharing options...
Alpha-Linux Posted May 23, 2017 Share #1025 Posted May 23, 2017 Mellanox ConnectX-3 VPI Adapter / MCX354A-FCBT Would love to see Mellanox ConnectX-3 VPI driver support. It just needs to support 40Gig Ethernet Mode (no Infiniband) On CentOS 7 I'm using Mellanox Linux Driver 4.0-2.0.0.1 which works perfectly thanks ! Link to comment Share on other sites More sharing options...
Recommended Posts