pocopico Posted April 7, 2022 Author Share #2051 Posted April 7, 2022 11 hours ago, coint_cho said: /usr/lib/modules-load.d/70-cpufreq-kernel.conf had the original acpi-cpufreq commented out with #. Tried with both pocopico redpill.misc and jumkey redpill.misc, able to install pat on Proxmox VM, after restarting, still not able to access the setup page in any form or way. At a loss here, and if there's no solution, might just downgrade back to 7.0.1-42218 and stay there https://streamable.com/1i0xsl Demo of the current issue I'm facing after installation of PAT. This happens cuase a systemd prerequisite has fail to load you can check with : sudo systemctl list-units --failed ## OR ## sudo systemctl list-units --state failed Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 7, 2022 Author Share #2052 Posted April 7, 2022 2 hours ago, Dvalin21 said: @pocopico and @Peter Suh Its it possible to make tc use tg3 anyway? I tried the force_add and it just says that tg3 is already added. Is there a way disable the ext check for a short period of time? yes it was requested in the past ... assuming that you have loaded what ever extensions you need manually, you can use : ./rploader.sh build xxxxx manual 1 Quote Link to comment Share on other sites More sharing options...
RacerX Posted April 7, 2022 Share #2053 Posted April 7, 2022 What is your satamap and diskid again? "SataPortMap": "58", "DiskIdxMap": "0A00" https://imgur.com/a/rEHmoZo Quote Link to comment Share on other sites More sharing options...
coint_cho Posted April 7, 2022 Share #2054 Posted April 7, 2022 39 minutes ago, pocopico said: This happens cuase a systemd prerequisite has fail to load you can check with : sudo systemctl list-units --failed ## OR ## sudo systemctl list-units --state failed Ok, looks like my NIC is the issue here.. And looks like there’s some other issues as well, is there any solutions to any of these? If these are Ethernet based errors, maybe switching to vmxnet3 would help? Or virtio? Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 7, 2022 Author Share #2055 Posted April 7, 2022 7 minutes ago, coint_cho said: Ok, looks like my NIC is the issue here.. And looks like there’s some other issues as well, is there any solutions to any of these? If these are Ethernet based errors, maybe switching to vmxnet3 would help? Or virtio? The systemd-modules-load.service is a prerequisite for most systemd services. You can check details of systemd-modules-load.service : sudo systemctl status systemd-modules-load.service Quote Link to comment Share on other sites More sharing options...
coint_cho Posted April 7, 2022 Share #2056 Posted April 7, 2022 8 minutes ago, pocopico said: The systemd-modules-load.service is a prerequisite for most systemd services. You can check details of systemd-modules-load.service : sudo systemctl status systemd-modules-load.service Here’s the output to that. Quote Link to comment Share on other sites More sharing options...
alienman Posted April 7, 2022 Share #2057 Posted April 7, 2022 23 hours ago, Indio said: Hi, thank you once again for trying to help. I think the logs will be long. Hope you can find what I am doing wrong: I think the problem starts here: Here is the dmesg from tc: The Hdd in proxmox as scsi is: [ 572.815557] sd 14:0:0:0: [sdh] 488397168 512-byte logical blocks: (250 GB/233 GiB) dmesg from DSM: Same result: Hi @Indio, The module is running. It's sufficient to see in the dmesg log of the DSM the lines "... smart_shim.c:818> Handling ioctl ...". So until here, all is right installed. Regarding your problem, I see that all seems OK with the HD. What's the problem now? Remember that I'm using VMWARE ESXi and not PROMOX. So I don't know how to enable VIRTUAL SSD in the qemu configuration. However, I feel it can be enabled. Search in the documentation about how to mark a virtual harddisk as SSD. Regards. Quote Link to comment Share on other sites More sharing options...
RedwinX Posted April 7, 2022 Share #2058 Posted April 7, 2022 (edited) 1 hour ago, alienman said: Hi @Indio, The module is running. It's sufficient to see in the dmesg log of the DSM the lines "... smart_shim.c:818> Handling ioctl ...". So until here, all is right installed. Regarding your problem, I see that all seems OK with the HD. What's the problem now? Remember that I'm using VMWARE ESXi and not PROMOX. So I don't know how to enable VIRTUAL SSD in the qemu configuration. However, I feel it can be enabled. Search in the documentation about how to mark a virtual harddisk as SSD. Regards. VMware ESXi didn't work for me. The only worked version installed for me is 7.0.1-42218 (918+ but whatever version), and I didn't remember how I did... The only think I know/see is that it's mandatory to have 2 network interfaces to get 1 working (5 for 3622xs+). Current working version (7.0.1) has 2 network insterface and it work. BIOS mode and that's it... 1 vmdk (convert with v2v converter) in SATA 0:0 and 1 disk of DATA (4To thin provisioning) in SATA 0:1. Cannot reproduce a working VM with same configuration with current redpill-loader, 7.0.1 or 7.1. Try many platform, not working. No visible error at boot (serial console). First boot and install are ok. But said that the system is in repair state after first reboot. @pocopicoI'm wondering if the kernel has not change, because the RC version has disapear, but have the same build number. Do you think I have to regenerate the BSP ? Regenerating now, and compare the 2 files... I will let you know EDIT : same binary... And just for information, I'm on ESXi 7.0u2. @pocopicoCannot boot with your vmdk tinycore, it said that it's an incorrect format. The only way to get a working version is to convert the img to vmdk (v2v converter) Edited April 7, 2022 by RedwinX Quote Link to comment Share on other sites More sharing options...
igbs Posted April 7, 2022 Share #2059 Posted April 7, 2022 (edited) Hello pocopico, Please correct extention: https://github.com/pocopico/rp-ext/blob/main/atlantic/rpext-index.json I've got errors: [!] Failed to dump extension pocopico.atlantic for platform ds920p_42218 as its recipe file cannot be retrieved. Isn't the extension misspelled or not supported on that platform? [#] Verifying /home/tc/redpill-load/custom/extensions/pocopico.atlantic/ds920p_42218/check-atlantic.sh file... [OK] [-] Recipe file for extension pocopico.atlantic platform ds920p_42218 is logically invalid - recipe defines kmod crc-itu-t.ko *FILE* which doesn't exist after all files entries are processed. You SHOULD contact the extension packer to report that (see below) Thanks Edited April 7, 2022 by igbs Quote Link to comment Share on other sites More sharing options...
alirz1 Posted April 7, 2022 Share #2060 Posted April 7, 2022 On 4/6/2022 at 2:08 AM, pocopico said: You need to change the VMX file for the network interface to "e1000e" which works with most platforms (except the AMD ones). Another option would be to leave it as is and recreate the loader but add the e1000 or vmxnet3 extension before you build the loader (vmxnet3 is always the best option for vmware VMs in terms of speed etc) ./rploader.sh ext broadwellnk-7.1.0-42621 add https://github.com/pocopico/rp-ext/raw/main/e1000/rpext-index.json or ./rploader.sh ext broadwellnk-7.1.0-42621 add https://github.com/pocopico/rp-ext/raw/main/vmxnet3/rpext-index.json VGA output is missing from the syno kernel. I you are using VM workstation, you can create a serial port and putty to it. This way you will see all kernel boot messages and finally log into the VM. You can then use putty to connect to that serial \\.\pipe\ds920p_710 ok so i rebuilt the loader after adding the vmxnet3 NIC extension. I also setup the serial port connection so i could see what was going on the with teh VM after the loader's" Booting booting" mesage. So this is where my vm seems to be hanging as i see in the serial console, below are the last few lines. See attached txt file for the rest of the full log: [ 11.066021] NET: Registered protocol family 1 [ 11.067442] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 11.069501] pci 0000:00:0f.0: Boot video device [ 11.105811] PCI: CLS 32 bytes, default 64 [ 12.921287] Trying to unpack rootfs image as initramfs... [ 13.718257] Freeing initrd memory: 18992k freed [ 13.763415] redpill: module verification failed: signature and/or required key missing - tainting kernel log.txt Quote Link to comment Share on other sites More sharing options...
Bose321 Posted April 7, 2022 Share #2061 Posted April 7, 2022 (edited) Can someone help me with getting it to work on Unraid? After building it does seem to build. but it seems like there is no network attached. I only see lo when I do ifconfig on the cli. I've tried both virtio and virtio-net and br0 and virtual br0. Even tried adding two interfaces. The weird thing is that I do see the eth0 and eth1 interfaces when I am in the loader... But not after building in DSM. Also tried to add this, but not working: https://github.com/jumkey/redpill-load/raw/develop/redpill-virtio/rpext-index.json Edited April 7, 2022 by Bose321 Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 7, 2022 Author Share #2062 Posted April 7, 2022 4 hours ago, alirz1 said: ok so i rebuilt the loader after adding the vmxnet3 NIC extension. I also setup the serial port connection so i could see what was going on the with teh VM after the loader's" Booting booting" mesage. So this is where my vm seems to be hanging as i see in the serial console, below are the last few lines. See attached txt file for the rest of the full log: [ 11.066021] NET: Registered protocol family 1 [ 11.067442] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 11.069501] pci 0000:00:0f.0: Boot video device [ 11.105811] PCI: CLS 32 bytes, default 64 [ 12.921287] Trying to unpack rootfs image as initramfs... [ 13.718257] Freeing initrd memory: 18992k freed [ 13.763415] redpill: module verification failed: signature and/or required key missing - tainting kernel log.txt 47.4 kB · 2 downloads I only saw that on DVA3221. For some reason (that I didn’t have time to look up) the console stops there. Did you try any other version ? 1 Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 7, 2022 Author Share #2063 Posted April 7, 2022 5 hours ago, igbs said: Hello pocopico, Please correct extention: https://github.com/pocopico/rp-ext/blob/main/atlantic/rpext-index.json I've got errors: [!] Failed to dump extension pocopico.atlantic for platform ds920p_42218 as its recipe file cannot be retrieved. Isn't the extension misspelled or not supported on that platform? [#] Verifying /home/tc/redpill-load/custom/extensions/pocopico.atlantic/ds920p_42218/check-atlantic.sh file... [OK] [-] Recipe file for extension pocopico.atlantic platform ds920p_42218 is logically invalid - recipe defines kmod crc-itu-t.ko *FILE* which doesn't exist after all files entries are processed. You SHOULD contact the extension packer to report that (see below) Thanks Extensions will be rebuilt soon 2 Quote Link to comment Share on other sites More sharing options...
alirz1 Posted April 7, 2022 Share #2064 Posted April 7, 2022 50 minutes ago, pocopico said: I only saw that on DVA3221. For some reason (that I didn’t have time to look up) the console stops there. Did you try any other version ? I have only tried ds3615 for now. I can try building for another model. Quote Link to comment Share on other sites More sharing options...
Dvalin21 Posted April 7, 2022 Share #2065 Posted April 7, 2022 58 minutes ago, pocopico said: Extensions will be rebuilt soon Hey, just wanted to say thank you. No complaints, no errors, no issues, just thank you for all you do and all those who help you out. 2 Quote Link to comment Share on other sites More sharing options...
igbs Posted April 7, 2022 Share #2066 Posted April 7, 2022 4 minutes ago, Dvalin21 said: Hey, just wanted to say thank you. No complaints, no errors, no issues, just thank you for all you do and all those who help you out. Join as well... Big thank you! 1 Quote Link to comment Share on other sites More sharing options...
RacerX Posted April 8, 2022 Share #2067 Posted April 8, 2022 Regarding the Test LSI 9207 1000:0087 that I have been trying with DS3622 lspci -k 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3 Processor DRAM Controller (rev 06) Subsystem: Super Micro Computer Inc Device 0804 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) Kernel driver in use: pcieport 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B xHCI (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: xhci_hcd 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B EHCI #2 (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ehci-pci 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #1 (rev d5) Kernel driver in use: pcieport 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #3 (rev d5) Kernel driver in use: pcieport 00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #4 (rev d5) Kernel driver in use: pcieport 00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #5 (rev d5) Kernel driver in use: pcieport 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B EHCI #1 (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ehci-pci 00:1f.0 ISA bridge: Intel Corporation C222 Series Chipset Family Server Essentia l SKU LPC Controller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: lpc_ich 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6 -port SATA Controller 1 [AHCI mode] (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Contr oller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 00:1f.6 Signal processing controller: Intel Corporation 8 Series Chipset Family Thermal Management Controller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: intel_pch_thermal 01:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS2308 PCI-E xpress Fusion-MPT SAS-2 (rev 05) Subsystem: LSI Logic / Symbios Logic 9207-8i SAS2.1 HBA 02:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 03) 03:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Famil y (rev 30) Subsystem: Super Micro Computer Inc Device 0804 04:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection ( rev 03) Subsystem: Super Micro Computer Inc Device 1533 Kernel driver in use: igb 05:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection ( rev 03) Subsystem: Super Micro Computer Inc Device 1533 Kernel driver in use: igb 06:00.0 Ethernet controller: Intel Corporation 82599 10 Gigabit Network Connecti on (rev 01) Subsystem: Super Micro Computer Inc Device 0659 Kernel driver in use: ixgbe tc@box:~$ lspci -Q | grep -E '(AHCI|LSI)' 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 01:00.0 Serial Attached SCSI controller: Broadcom / LSI SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05) With DS3617, it loads the extension automatically for mpt2sas Found SAS Controller : pciid 1000d00000087 Required Extension : mpt2sas Searching for matching extension for mpt2sas Found matching extension : "https://raw.githubusercontent.com/pocopico/rp-ext/master/mpt2sas/rpext-index.json" However, when I test DS3617 ./rploader.sh build bromolow-7.0.1-42218 I get the same message as with DS3622 broadwellnk-7.0.1-42218 when it boots " no drives detected" The sata config So 6+8 = 14 I tried 6, 14, and the stock 58 I can still test ds918 However, if the extension needs an update I found this on the web that says the LSi 9207 card 1000:0087 works with kernels 4.4 - 5.17 http://linux-hardware.org/index.php?id=pci:1000-0087-1590-0041 mpt3sas_scsih.c Quote Link to comment Share on other sites More sharing options...
Dvalin21 Posted April 8, 2022 Share #2068 Posted April 8, 2022 (edited) 21 minutes ago, RacerX said: Regarding the Test LSI 9207 1000:0087 that I have been trying with DS3622 lspci -k 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3 Processor DRAM Controller (rev 06) Subsystem: Super Micro Computer Inc Device 0804 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) Kernel driver in use: pcieport 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B xHCI (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: xhci_hcd 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B EHCI #2 (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ehci-pci 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #1 (rev d5) Kernel driver in use: pcieport 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #3 (rev d5) Kernel driver in use: pcieport 00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #4 (rev d5) Kernel driver in use: pcieport 00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #5 (rev d5) Kernel driver in use: pcieport 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B EHCI #1 (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ehci-pci 00:1f.0 ISA bridge: Intel Corporation C222 Series Chipset Family Server Essentia l SKU LPC Controller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: lpc_ich 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6 -port SATA Controller 1 [AHCI mode] (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Contr oller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 00:1f.6 Signal processing controller: Intel Corporation 8 Series Chipset Family Thermal Management Controller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: intel_pch_thermal 01:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS2308 PCI-E xpress Fusion-MPT SAS-2 (rev 05) Subsystem: LSI Logic / Symbios Logic 9207-8i SAS2.1 HBA 02:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 03) 03:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Famil y (rev 30) Subsystem: Super Micro Computer Inc Device 0804 04:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection ( rev 03) Subsystem: Super Micro Computer Inc Device 1533 Kernel driver in use: igb 05:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection ( rev 03) Subsystem: Super Micro Computer Inc Device 1533 Kernel driver in use: igb 06:00.0 Ethernet controller: Intel Corporation 82599 10 Gigabit Network Connecti on (rev 01) Subsystem: Super Micro Computer Inc Device 0659 Kernel driver in use: ixgbe tc@box:~$ lspci -Q | grep -E '(AHCI|LSI)' 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 01:00.0 Serial Attached SCSI controller: Broadcom / LSI SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05) With DS3617, it loads the extension automatically for mpt2sas Found SAS Controller : pciid 1000d00000087 Required Extension : mpt2sas Searching for matching extension for mpt2sas Found matching extension : "https://raw.githubusercontent.com/pocopico/rp-ext/master/mpt2sas/rpext-index.json" However, when I test DS3617 ./rploader.sh build bromolow-7.0.1-42218 I get the same message as with DS3622 broadwellnk-7.0.1-42218 when it boots " no drives detected" The sata config So 6+8 = 14 I tried 6, 14, and the stock 58 I can still test ds918 However, if the extension needs an update I found this on the web that says the LSi 9207 card 1000:0087 works with kernels 4.4 - 5.17 http://linux-hardware.org/index.php?id=pci:1000-0087-1590-0041 mpt3sas_scsih.c Try SataMap 68 DiskIdxMap 0007 SasIdxMap 0 should place your lsi card drives in order. if that doesnt work remove 8, make disk 00 and keep SasIdxMap. Reason being, right now just using lsi card i have NO satamap or diskidxmap set and it works as should. Keep Sasidxmap to keep drives in order Edited April 8, 2022 by Dvalin21 Quote Link to comment Share on other sites More sharing options...
cferra Posted April 8, 2022 Share #2069 Posted April 8, 2022 (edited) 23 minutes ago, RacerX said: Regarding the Test LSI 9207 1000:0087 that I have been trying with DS3622 lspci -k 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3 Processor DRAM Controller (rev 06) Subsystem: Super Micro Computer Inc Device 0804 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) Kernel driver in use: pcieport 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B xHCI (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: xhci_hcd 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B EHCI #2 (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ehci-pci 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #1 (rev d5) Kernel driver in use: pcieport 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #3 (rev d5) Kernel driver in use: pcieport 00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #4 (rev d5) Kernel driver in use: pcieport 00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Ex press Root Port #5 (rev d5) Kernel driver in use: pcieport 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family US B EHCI #1 (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ehci-pci 00:1f.0 ISA bridge: Intel Corporation C222 Series Chipset Family Server Essentia l SKU LPC Controller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: lpc_ich 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6 -port SATA Controller 1 [AHCI mode] (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Contr oller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 00:1f.6 Signal processing controller: Intel Corporation 8 Series Chipset Family Thermal Management Controller (rev 05) Subsystem: Super Micro Computer Inc Device 0804 Kernel driver in use: intel_pch_thermal 01:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS2308 PCI-E xpress Fusion-MPT SAS-2 (rev 05) Subsystem: LSI Logic / Symbios Logic 9207-8i SAS2.1 HBA 02:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 03) 03:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Famil y (rev 30) Subsystem: Super Micro Computer Inc Device 0804 04:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection ( rev 03) Subsystem: Super Micro Computer Inc Device 1533 Kernel driver in use: igb 05:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection ( rev 03) Subsystem: Super Micro Computer Inc Device 1533 Kernel driver in use: igb 06:00.0 Ethernet controller: Intel Corporation 82599 10 Gigabit Network Connecti on (rev 01) Subsystem: Super Micro Computer Inc Device 0659 Kernel driver in use: ixgbe tc@box:~$ lspci -Q | grep -E '(AHCI|LSI)' 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 01:00.0 Serial Attached SCSI controller: Broadcom / LSI SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05) With DS3617, it loads the extension automatically for mpt2sas Found SAS Controller : pciid 1000d00000087 Required Extension : mpt2sas Searching for matching extension for mpt2sas Found matching extension : "https://raw.githubusercontent.com/pocopico/rp-ext/master/mpt2sas/rpext-index.json" However, when I test DS3617 ./rploader.sh build bromolow-7.0.1-42218 I get the same message as with DS3622 broadwellnk-7.0.1-42218 when it boots " no drives detected" The sata config So 6+8 = 14 I tried 6, 14, and the stock 58 I can still test ds918 However, if the extension needs an update I found this on the web that says the LSi 9207 card 1000:0087 works with kernels 4.4 - 5.17 http://linux-hardware.org/index.php?id=pci:1000-0087-1590-0041 mpt3sas_scsih.c For 3622, the mpt2sas driver is already incorporated into the mpt3sas driver / extension. if you need to manually add that, you can. is your HBA card in IT or RAID mode? It would be better for you if it were in IT mode. Edited April 8, 2022 by cferra Quote Link to comment Share on other sites More sharing options...
RacerX Posted April 8, 2022 Share #2070 Posted April 8, 2022 My card is HBA no raid. I tried with the extensions and mpt2sas an mpt3sas no luck but it it is the sata config then the test is bad.. My system only has drives on LSI sata is turned off in bios I don't think it matters. Because LSPCI knows all...... I'll test Dvalin21 fixes now be back in a bit Thank You Quote Link to comment Share on other sites More sharing options...
RacerX Posted April 8, 2022 Share #2071 Posted April 8, 2022 Well I tried all the combinations and upgraded wit the extension https://raw.githubusercontent.com/pocopico/rp-ext/master/mpt3sas/rpext-index.json It didn't work so I'll try DS 918 and update this thread later Thanks Quote Link to comment Share on other sites More sharing options...
Xenos Posted April 8, 2022 Share #2072 Posted April 8, 2022 (edited) Board ECS BAT-I2 V1.0 (J1800 w/Realtek Eth) Installing from a scratch. Empty tc homedir after boot - no .sh/.json. Apparently no redpill loaded. How to fix? Edited April 8, 2022 by Xenos Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted April 8, 2022 Share #2073 Posted April 8, 2022 2 hours ago, RacerX said: Well I tried all the combinations and upgraded wit the extension https://raw.githubusercontent.com/pocopico/rp-ext/master/mpt3sas/rpext-index.json It didn't work so I'll try DS 918 and update this thread later Thanks I tried three of the seven platforms, ds918, ds920, and ds3622 at BAREMETAL The only ds3622 and HBA were able to operate stably. The ds920 / ds1621 using dts does not recognize the HDD at all. @pocopico seems to be able to test mainly on VM. He must be very busy, but ds920 / ds1621 would like @pocopico to pre-test at BAREMETAL. Too much energy is consumed by users for testing. Quote Link to comment Share on other sites More sharing options...
RacerX Posted April 8, 2022 Share #2074 Posted April 8, 2022 Thanks Peter that's good to know.... Quote Link to comment Share on other sites More sharing options...
titoum Posted April 8, 2022 Share #2075 Posted April 8, 2022 49 minutes ago, Peter Suh said: He must be very busy, but ds920 / ds1621 would like @pocopico to pre-test at BAREMETAL. Too much energy is consumed by users for testing. i don't really share this point of view tbh... It might be better to have people that really want to have those version on a BareMetal testing it and reporting/fixing. As you mentioned, he should be quite overloaded already so asking for more from a person doing that during free time doesn't make sense. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.