frank_zero

[SOLVED] Install on vmware ESXI

Recommended Posts

I'm still running 4.2-3202 on ESXi 5.1U2 and it seems like my Synology VM utilizes all my CPU, even when idle. Has anyone else seen this? I'm using RDM for my drives, and really haven't installed anything else. Is there a way to see what's running currently and what's taking up the CPU?

 

EDIT: Let me clarify - the CPU usage is high in the VMWare Console, but when I log into the Synology itself, CPU is low and it doesn't appear that anything is running. Something has to be, perhaps something that's not tracked by the internal monitors.

 

You might have been hacked.

 

Update to a higher version

Share this post


Link to post
Share on other sites
I'm still running 4.2-3202 on ESXi 5.1U2 and it seems like my Synology VM utilizes all my CPU, even when idle. Has anyone else seen this? I'm using RDM for my drives, and really haven't installed anything else. Is there a way to see what's running currently and what's taking up the CPU?

 

EDIT: Let me clarify - the CPU usage is high in the VMWare Console, but when I log into the Synology itself, CPU is low and it doesn't appear that anything is running. Something has to be, perhaps something that's not tracked by the internal monitors.

 

You might have been hacked.

 

Update to a higher version

I didn't think 4.2-3202 was susceptible to the hack that plagued 4.3? I can't upgrade at the moment so is there a way to find out what's running and shut it down?

Share this post


Link to post
Share on other sites

i got 5.0 with update 2 installed in esxi 5.5 using gnoboot-alpha10.3-custom-ESXi-vfat-flat.vmdk

But i cant locate menu_alpha.lst so i can give it a serial.

i have tried searching with winscp. but i cant finde it.

 

anyone got a idea how to locate and edit this file?

Share this post


Link to post
Share on other sites
i got 5.0 with update 2 installed in esxi 5.5 using gnoboot-alpha10.3-custom-ESXi-vfat-flat.vmdk

But i cant locate menu_alpha.lst so i can give it a serial.

i have tried searching with winscp. but i cant finde it.

 

anyone got a idea how to locate and edit this file?

It's in usbshare1/boot/grub folder. :mrgreen:

Share this post


Link to post
Share on other sites
i got 5.0 with update 2 installed in esxi 5.5 using gnoboot-alpha10.3-custom-ESXi-vfat-flat.vmdk

But i cant locate menu_alpha.lst so i can give it a serial.

i have tried searching with winscp. but i cant finde it.

 

anyone got a idea how to locate and edit this file?

It's in usbshare1/boot/grub folder. :mrgreen:

 

There are no usbshare1 for gnoboot when using the esxi image.

usbshare1 is mounted as my external usb drive.

 

The solution was to convert the vmdk file to img and mount it using OSFMount and then edit the file.

after this, it is easy to convert back to vmdk and it works perfectly.

 

dos anyone know why the PDMs are mounted as SSD in DSM?

Share this post


Link to post
Share on other sites

I tried multiple times on ESXI 5.5 and when it boots up, it doesn't recognize the data hard drive.

I've tried mapping, SCSI and IDE... never sees a drive.. Trying to run the "install" from the helper gives an error 38, and the web UI says no drives.

What's the root password for an uninitialized synology?

Anyone have recommendations?

Thanks in advance.. if i find the error, I'll post a reply.

Share this post


Link to post
Share on other sites

Hi,

 

i want to install xpenology on Vmware workstation. I did this :

-create a new virtual machine

-install knoppix, copy gnoboot-alpha10.5-ext2.img

-reset the VM, select gnoboot.me

-choose gnoboot 5.0 - 4458

- Gnoboot has an Ip address, i started Synology Assistant and send DSM_DS3612xs_4458.pat

- and when installation begins i have error 38 with telnet that not redirect to my host, but i have redirect the port 23 from my router to my VM.

 

What's wrong ?

 

Thank's for your answear.

Share this post


Link to post
Share on other sites

Hi

 

The easyest way i found was to create a floppy drive booting plpbt.img (which is plop boot manager : http://www.plop.at/en/bootmanager/plpbt.bin.html ). Then you can make your VM boot from USB ...

you'll just have to plug an usb key containing whatever Xpenology / gnoboot version.

But for your current setup , i have no idea ... sorry.

Share this post


Link to post
Share on other sites

My easiest way (gnoboot) is:

- Use StarWind V2V converter.

- Convert *vfat.img to "VMware ESX server image". You get two *.vmdk files.

- In vSphere client create new custom VM.

- Guest operating system Linux CentOS 64-bit works for me.

- NIC e1000.

- Default SCSI controller LSI logic parallel. VMware Paravirtual works too.

- Create new disk (8 GB is sufficient for testing).

- Select SCSI (0:1) because this is not the boot disk.

- Finish, Edit settings, remove CD/Floppy (probably not necessary but I like to have things simple).

- Open datastore / location of you VM.

- Upload the two vmdk files created by V2V.

- Edit VM settings, add hard disk, existing, browse to datastore / location of your VM, select 32 MB gnoboot vmdk.

- Select SCSI (0:0) because this is the boot disk.

- Edit VM settings, options, set Power On Boot Delay to e.g. 9000.

- Power on VM, open console.

- In grub select gnoboot.me then 4458.

- VM console tells you the IP, point browser to that IP, install DSM_DS3612xs_4458.pat from computer.

- Let VM reboot with gnoboot/grub defaults. Done. Enjoy.

Share this post


Link to post
Share on other sites

Hi here is my post on DSM 4.3.

 

I;m running on VMware ESX 5.5 with an Adaptec 5805 I created 8 JBOD disks and presented them to ESX. Once the XPEnology guest was created I added the 8 disks to XPE. and enabled SHR. Config is as advised 2 sockets with each 1 core and 2 GB memory.

 

All is working good but looking for some reference for reade/write:

 

I did some tests and here are my results:

READ 50 MB/s

WRITE 80-100 MB/s

 

Not sure why this is I would expect a higher read speed in this setup?

 

What are your rates in ESX, i'm curious.

 

Cheers,

 

Hemant

Share this post


Link to post
Share on other sites

What is the recommended configuration for ESXi (5.5)?

I'm going to use GNOboot. Just tried it but before I'm building a "production" build I would like to know the best config.

 

I created the following:

Other 2.6.x Linux x64

LSI Logic Parallel controller

2GB ram

 

But what do I need to change/add to my config?

1 or 2 virtual cpu sockets

1 or 2 cores per socket

Does the 2GB need to be reserved (edit VM settings -> resources)?

 

Any other tips?

Share this post


Link to post
Share on other sites
What is the recommended configuration for ESXi (5.5)?

I'm going to use GNOboot. Just tried it but before I'm building a "production" build I would like to know the best config.

 

I created the following:

Other 2.6.x Linux x64

LSI Logic Parallel controller

2GB ram

 

But what do I need to change/add to my config?

1 or 2 virtual cpu sockets

1 or 2 cores per socket

Does the 2GB need to be reserved (edit VM settings -> resources)?

 

Any other tips?

 

my suggestion wud be using my guide here, - http://cyanlabs.co.uk/news/how-to-insta ... gy-on-esxi

Share this post


Link to post
Share on other sites

Hello,

 

how i can Change my mac address for DSM 4.1 (trantor) in VMware ESXi?

 

Thanks!

 

Many greets, iceget

Share this post


Link to post
Share on other sites

VMware ESX and ESXi are VMware's enterprise software Type 1 hypervisors for guest virtual servers they run on host server hardware without an underlying operating system.

Share this post


Link to post
Share on other sites

hi! How i can change mac to correct to work quick connect. when i try change mac at VM - mac is not correct

Share this post


Link to post
Share on other sites
I'm still running 4.2-3202 on ESXi 5.1U2 and it seems like my Synology VM utilizes all my CPU, even when idle. Has anyone else seen this? I'm using RDM for my drives, and really haven't installed anything else. Is there a way to see what's running currently and what's taking up the CPU?

 

EDIT: Let me clarify - the CPU usage is high in the VMWare Console, but when I log into the Synology itself, CPU is low and it doesn't appear that anything is running. Something has to be, perhaps something that's not tracked by the internal monitors.

 

It may be IPMI. In my configuration with asrock E3C226D2I m/b, ESXi pulls CPU all the time till I switch off IPMI sensors.

 

Quotation from amazon review:

VMWARE ESXi STABILITY NOTE: ESXi has an issue with many motherboards that have IPMI sensors on board where a runaway process will consume most of the CPU timeslices even without any guest OS running. A workaround for this problem is to go into Configuration -> Software -> Advanced Settings -> VMkernel -> VMkernel.Boot.ipmiEnabled and uncheck the box. Unfortunately you lose the ability to monitor temperatures, fan speeds, etc. with VMware (vSphere Client among others) software. Fortunately you can go into the web-interface for the IPMI and see the same information.

Share this post


Link to post
Share on other sites

Hi,

 

I now have XPEnology 5.0-4528 running under ESXI (NL54 Microsever), everything seems fine but both NZBGET and/or SABNZB seem to download very slowly I just can't seem to work out why!!!

 

Downloads work but I never seem to get a download above 800 kbps (should be getting about 2 mbps).

 

Not sure where to look, any help appreciated.

 

Thanks

 

HEADRAT

Share this post


Link to post
Share on other sites

LOL, I worked out why, had a powercut last night and it borked my broadband, reset router and everything is fine !!

Share this post


Link to post
Share on other sites

Hi all,

 

I'm actually looking for a solution.

 

I have server machine from OVH in france, because i'm french and I want to put a xpenology on it. Its system is ESXI 5.0, and my problem with the xpenology is that I can't make a correct network configuration for Failover IP of the xpenology. I launch the xpenology VM by a Nanoboot for ESXI.

 

If you can help me...

 

Thanks a lot for you future response !

Share this post


Link to post
Share on other sites

vSphere ESXi logs all user activity from both the Shell and the Direct Console User Interface under the user's account. This logging ensures user accountability and makes it easy to audit user activity.

Share this post


Link to post
Share on other sites

Hello,

 

I have got 5.2 installed on a VM and it was working really well, I rdm the raid drives etc, but I have just upped the 50GB vm hdd to 100GB and now all i get is stuck at starting services ! anything I can do here as it has taken me a while to get this to this point

 

 

thanks

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now