Jizar Stoffel Posted April 21, 2022 Share #2926 Posted April 21, 2022 1 minute ago, phone guy said: You did read what I said about your 8 port sata card right? yes, funny thing is that this card was running fine on DSM 6.2, do you know of any 8port card I can use? 1 Quote Link to comment Share on other sites More sharing options...
phone guy Posted April 21, 2022 Share #2927 Posted April 21, 2022 (edited) 9 minutes ago, Jizar Stoffel said: yes, funny thing is that this card was running fine on DSM 6.2, do you know of any 8port card I can use? I had a 2nd nic port that worked in dsm623 with jun104b loader, that I had to talk dirty to in order to make it work too! I had to install a modified driver for that 2nd nic because it was on the usb bus not the pci bus, but it worked in dsm6, not in dsm7. 🤪 The jmb575 sata card work, no switch but 5 ports. I dont know of any 8 port sata, that why I ordered the sas card. 8 sata ports, and the 3622 is supposed to work great with those since the real 3622 uses similar or same type of interface. You need a sas HBA IT MODE card, recommendations are Dell H200/H310, IBM 1015, LSI 9211 8i. These are all over ebay with cables for about $50 USD. Once flashed to it mode, they are all the same... there are other models with pci3.0 x8 if your mobo has that (it probably does), but unless your running ssd drives, pci2.0 x8 is enough for 8 spinning HDD. The advantage to ahci sata is no additional drivers, but I dont know of 1 with 8 ports and no switch/multiplexer - that doesnt mean it doesnt exist, you'd have to research your choice of sata card and verify NO SWITCH Edited April 21, 2022 by phone guy Quote Link to comment Share on other sites More sharing options...
scoobdriver Posted April 21, 2022 Share #2928 Posted April 21, 2022 So I have ran DS918+ in a VM , starting at7.0.1-42218 and updating to 7.0.1-42218 U3 no problem . (and further to 7.1) I tried DS3622xs+ on bare metal , it installs 7.0.1-42218 no problem but if I manual install the update 3 pat file from the gui it just puts me in a recover loop . Is there any way to update to U3 on DS3622xs+ , or do I need to stay on 7.0.1 U1 , (I don't want to install 7.1 due to the complications with Advanced Media Extension, and Synology surveillance Station ) Is there a way out the recovery loop ? Quote Link to comment Share on other sites More sharing options...
Jizar Stoffel Posted April 21, 2022 Share #2929 Posted April 21, 2022 14 minutes ago, phone guy said: I had a 2nd nic port that worked in dsm623 with jun104b loader, that I had to talk dirty to in order to make it work too! I had to install a modified driver for that 2nd nic because it was on the usb bus not the pci bus, but it worked in dsm6, not in dsm7. 🤪 The jmb575 sata card work, no switch but 5 ports. I dont know of any 8 port sata, that why I ordered the sas card. 8 sata ports, and the 3622 is supposed to work great with those since the real 3622 uses similar or same type of interface. You need a sas HBA IT MODE card, recommendations are Dell H200/H310, IBM 1015, LSI 9211 8i. These are all over ebay with cables for about $50 USD. Once flashed to it mode, they are all the same... there are other models with pci3.0 x8 if your mobo has that (it probably does), but unless your running ssd drives, pci2.0 x8 is enough for 8 spinning HDD. The advantage to ahci sata is no additional drivers, but I dont know of 1 with 8 ports and no switch/multiplexer - that doesnt mean it doesnt exist, you'd have to research your choice of sata card and verify NO SWITCH I need to do some research on this. my MB only has 2 pci slots. It seems it would be cheaper for me to buy another MB with more slots, since I already have about 3 4port PCI cards laying around somewhere. Quote Link to comment Share on other sites More sharing options...
Jizar Stoffel Posted April 21, 2022 Share #2930 Posted April 21, 2022 no go on the new installation procedure, still getting: Quote Link to comment Share on other sites More sharing options...
Jizar Stoffel Posted April 21, 2022 Share #2931 Posted April 21, 2022 changed mapping to 2/00 on loader boot menu. and got installation loop... next, ill try to do the same thing I did in the beguining, Ill install 7.0, and try to upgrade aftewards Quote Link to comment Share on other sites More sharing options...
RacerX Posted April 21, 2022 Share #2932 Posted April 21, 2022 (edited) I have encountered that "something went wrong message" before at the end of install. To get around it I shutdown the pc and put in a different nic and when i started it up it let me continue the install. Edited April 21, 2022 by RacerX Quote Link to comment Share on other sites More sharing options...
Jizar Stoffel Posted April 21, 2022 Share #2933 Posted April 21, 2022 ok, I got it installed by seting to 2/00 now... What is the proper way of changing satamap setting (perssistently) without having to rebuild loader? Quote Link to comment Share on other sites More sharing options...
nadiva Posted April 21, 2022 Share #2934 Posted April 21, 2022 14 hours ago, pocopico said: use gh repo // have to look into /var/log/junior_reason.log and /var/log/linuxrc* // use http://<yourip>:7681 (included in redpill-misc extension) thanks, will try again to see the logs. My old sata setup was 41 (4xRAID mvsas, 1xSATA on internal controller, 1xNVME on PCI card), is this output looking good to you? Quote HBA: 00:11.0 Disks : 1 HBA: 00:02.2 Disks : 8 ls: cannot access '/sys/devices/pci0000:00/0000:00:03.1/0000:04:00.0/port*': No such file or directory HBA: 00:03.1 Disks : 0 ls: cannot access '/sys/devices/pci0000:00/0000:00:03.1/0000:04:00.0/port*': No such file or directory SataPortMap=180 DiskIdxMap=000809 Quote Link to comment Share on other sites More sharing options...
phone guy Posted April 22, 2022 Share #2935 Posted April 22, 2022 Is there a tutorial for proxmox anyone? redpill dsm 7.1 proxmox 7.1-7 1 Quote Link to comment Share on other sites More sharing options...
Brunox Posted April 22, 2022 Share #2936 Posted April 22, 2022 9 hours ago, scoobdriver said: So I have ran DS918+ in a VM , starting at7.0.1-42218 and updating to 7.0.1-42218 U3 no problem . (and further to 7.1) I tried DS3622xs+ on bare metal , it installs 7.0.1-42218 no problem but if I manual install the update 3 pat file from the gui it just puts me in a recover loop . Is there any way to update to U3 on DS3622xs+ , or do I need to stay on 7.0.1 U1 , (I don't want to install 7.1 due to the complications with Advanced Media Extension, and Synology surveillance Station ) Is there a way out the recovery loop ? Hey, maybe this is a solution for you......read what buggy25200 write https://xpenology.com/forum/topic/45795-redpill-the-new-loader-for-624-discussion/?do=findComment&comment=260226 https://xpenology.com/forum/topic/45795-redpill-the-new-loader-for-624-discussion/?do=findComment&comment=261805 1 Quote Link to comment Share on other sites More sharing options...
scoobdriver Posted April 22, 2022 Share #2937 Posted April 22, 2022 (edited) 11 minutes ago, Brunox said: Hey, maybe this is a solution for you......read what buggy25200 write Thanks for the reply. It was actually 7.0.1 update 3 on Ds3622xs I was trying to run. buggy25200 seems to refer to 6.2.4 on DS918 Edited April 22, 2022 by scoobdriver Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 22, 2022 Share #2938 Posted April 22, 2022 (edited) On 4/21/2022 at 9:46 PM, phone guy said: The jmb575 sata card work slight but important mistake, jmb575 is a multiplier chip and cards with that one will not bring the results as it will end up in the amount of usable ports of the real sata controller on that card, worst case might be a 2 port sata chips and two jmb575 (each on every real sata port) looks like a 10 port card but will onlyx have 2 ports working with dsm (because synology prevents sata multiplexer except there own used in external units) the JMB one is JMB585 and beside one port more over the ancient marvell controllers it also has pcie 3.0, doubling the possible speed of over all data transfer (keep in mind the cip has only two pcie lanes usable) same as jmb585 is the asm1166 but has 6 ports (also two pcie lanes and up to pcie 3.0 speed) there are at least two 8 port ahci controllers but as they only based on pcie 2.0 chips there performance is not very good (especially when used with ssd's its a waste of money) - i wrote about these and also had a break down about the chips used and the max. performance that is to expect from the architecture the old pcie 2.0 lsi sas controllers are still a good choice when it comes to performance as the can use up to 8 pcie lanes (depending on the slot, they also work with less lanes, even with one but the performance will be less too) - as long as i dont have tested the lsi sas myself i would only use them with platforms where synology uses them too and use the original driver (that scenario limits possible choice to "older" varieties and the latest tri-mode might not be usable but that one might be to expansive anyway compared with the old trusty sas2008 based ones that need extra firmware flashing to have hba aka IT mode) tc loader has a newer mpt3sas driver but as long as i have not tested it thoroughly i'm not going to use it on a productive hardware, i have seen to much trouble with added drivers in 6.2, especially with 918+ Edited April 22, 2022 by IG-88 1 Quote Link to comment Share on other sites More sharing options...
Brunox Posted April 22, 2022 Share #2939 Posted April 22, 2022 (edited) 30 minutes ago, scoobdriver said: Thanks for the reply. It was actually 7.0.1 update 3 on Ds3622xs I was trying to run. buggy25200 seems to refer to 6.2.4 on DS918 No, this is definitely for the update from 7.0.1-42218 to 7.0.1-42218U3, I did it and it works fine with DS3617 Edited April 22, 2022 by Brunox Quote Link to comment Share on other sites More sharing options...
use-nas Posted April 22, 2022 Share #2940 Posted April 22, 2022 920+ MB: ASRock J3455-ITX SATA controller: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) Problem: one by one both controllers work, but together it doesn't work :(( When both work, then only internal_slot@1 and internal_slot@2 are visible in the system, internal_slot@3 and 4 are not present in the system and it does not depend on which controller the slots are configured on. Synology protection? Quote Link to comment Share on other sites More sharing options...
Bose321 Posted April 22, 2022 Share #2941 Posted April 22, 2022 After some messing around I finally got it working myself with the SATA settings. I was wondering, is it possible for my Unraid to send the shutdown command? Right now it does not listen to that. Am I missing extensions? Quote Link to comment Share on other sites More sharing options...
hendry Posted April 22, 2022 Share #2942 Posted April 22, 2022 after load ext v9fs, got some errors xpe | Loading kmod #0 "9pnet.ko" for pocopico.v9fs (args: ) xpe | [ 5.727074] 9pnet: module has bad taint, not creating trace events xpe | [ 5.728270] 9pnet: Installing 9P2000 support xpe | Loading kmod #1 "9pnet_virtio.ko" for pocopico.v9fs (args: ) xpe | [ 5.743823] 9pnet_virtio: Unknown symbol register_virtio_driver (err 0) xpe | [ 5.745222] 9pnet_virtio: Unknown symbol unregister_virtio_driver (err 0) xpe | [ 5.746617] 9pnet_virtio: Unknown symbol virtqueue_add_sgs (err 0) xpe | [ 5.747804] 9pnet_virtio: Unknown symbol virtqueue_get_buf (err 0) xpe | [ 5.748948] 9pnet_virtio: Unknown symbol virtqueue_kick (err 0) xpe | [ 5.750042] 9pnet_virtio: Unknown symbol virtio_check_driver_offered_feature (err 0) xpe | [ 5.751655] 9pnet_virtio: Unknown symbol register_virtio_driver (err 0) xpe | [ 5.752913] 9pnet_virtio: Unknown symbol unregister_virtio_driver (err 0) xpe | [ 5.754170] 9pnet_virtio: Unknown symbol virtqueue_add_sgs (err 0) xpe | [ 5.755298] 9pnet_virtio: Unknown symbol virtqueue_get_buf (err 0) xpe | [ 5.756439] 9pnet_virtio: Unknown symbol virtqueue_kick (err 0) xpe | [ 5.757533] 9pnet_virtio: Unknown symbol virtio_check_driver_offered_feature (err 0) xpe | insmod: can't insert '9pnet_virtio.ko': unknown symbol in module, or unknown parameter xpe | ERROR: kernel extensions "9pnet_virtio.ko" from pocopico.v9fs failed to load seems, the v9fs drivers cannot load on the new kernel. is it true ? i add ext from https://raw.githubusercontent.com/pocopico/rp-ext/master/v9fs/rpext-index.json if i didn't add it and just add https://raw.githubusercontent.com/pocopico/redpill-load/master/redpill-virtio/rpext-index.json, it's okay.. the network interfaces is available, but if i add v9fs ext, the network interface not available. @pocopicoplease kindly your help.. Quote Link to comment Share on other sites More sharing options...
mydownload Posted April 22, 2022 Share #2943 Posted April 22, 2022 On 4/18/2022 at 9:19 AM, mydownload said: Hi team ! Succeded to install DSM6.2 with redpill.v0.4.6. BUT, it seems configuration is not backuped, every time i reboot it, i need to reinstall Surveillance station and cracked it again. Does someone have an idea about reason ? thanks, Hi, no one else with this issue ? thanks, Quote Link to comment Share on other sites More sharing options...
romich7 Posted April 22, 2022 Share #2944 Posted April 22, 2022 I keep trying to build red-pill under Xen-Server. In rploader.sh, corrected the definition of disks in the expression $(mount | grep -i optional | grep cde | awk -F / '{print $3}' | uniq | cut -c 1-4) increased the length by one character (cut -c 1-3) was in the original version, made (cut -c 1-4). If it is possible to write an expression like (cut -c length($)-1) into the script, then tell me how to do it. As a result, when the script reaches the place where the .pat file is copied and unzipped, I get the error "cp: failed to preserve ownership for '/mnt/xvda3/auxfiles/ds3622xsp_42661.pat': Operation not permitted". What am I doing wrong? Quote Link to comment Share on other sites More sharing options...
scoobdriver Posted April 22, 2022 Share #2945 Posted April 22, 2022 2 hours ago, Brunox said: No, this is definitely for the update from 7.0.1-42218 to 7.0.1-42218U3, I did it and it works fine with DS3617 Apologies you're correct , the links were not taking me to the correct sections on mobile browser. I do see a process for DS3617 , I don't see anything for DS3622 , I'll investigate a bit further . Quote Link to comment Share on other sites More sharing options...
hendry Posted April 22, 2022 Share #2946 Posted April 22, 2022 1 hour ago, hendry said: after load ext v9fs, got some errors xpe | Loading kmod #0 "9pnet.ko" for pocopico.v9fs (args: ) xpe | [ 5.727074] 9pnet: module has bad taint, not creating trace events xpe | [ 5.728270] 9pnet: Installing 9P2000 support xpe | Loading kmod #1 "9pnet_virtio.ko" for pocopico.v9fs (args: ) xpe | [ 5.743823] 9pnet_virtio: Unknown symbol register_virtio_driver (err 0) xpe | [ 5.745222] 9pnet_virtio: Unknown symbol unregister_virtio_driver (err 0) xpe | [ 5.746617] 9pnet_virtio: Unknown symbol virtqueue_add_sgs (err 0) xpe | [ 5.747804] 9pnet_virtio: Unknown symbol virtqueue_get_buf (err 0) xpe | [ 5.748948] 9pnet_virtio: Unknown symbol virtqueue_kick (err 0) xpe | [ 5.750042] 9pnet_virtio: Unknown symbol virtio_check_driver_offered_feature (err 0) xpe | [ 5.751655] 9pnet_virtio: Unknown symbol register_virtio_driver (err 0) xpe | [ 5.752913] 9pnet_virtio: Unknown symbol unregister_virtio_driver (err 0) xpe | [ 5.754170] 9pnet_virtio: Unknown symbol virtqueue_add_sgs (err 0) xpe | [ 5.755298] 9pnet_virtio: Unknown symbol virtqueue_get_buf (err 0) xpe | [ 5.756439] 9pnet_virtio: Unknown symbol virtqueue_kick (err 0) xpe | [ 5.757533] 9pnet_virtio: Unknown symbol virtio_check_driver_offered_feature (err 0) xpe | insmod: can't insert '9pnet_virtio.ko': unknown symbol in module, or unknown parameter xpe | ERROR: kernel extensions "9pnet_virtio.ko" from pocopico.v9fs failed to load seems, the v9fs drivers cannot load on the new kernel. is it true ? i add ext from https://raw.githubusercontent.com/pocopico/rp-ext/master/v9fs/rpext-index.json if i didn't add it and just add https://raw.githubusercontent.com/pocopico/redpill-load/master/redpill-virtio/rpext-index.json, it's okay.. the network interfaces is available, but if i add v9fs ext, the network interface not available. @pocopicoplease kindly your help.. no one can solve this issue ? Quote Link to comment Share on other sites More sharing options...
likeme Posted April 22, 2022 Share #2947 Posted April 22, 2022 How to modify my ds920p.dts ? lrwxrwxrwx 1 root root 0 Apr 22 2022 sata1 -> ../devices/pci0000:00/0000:00:11.0/0000:02:03.0/ata1/host0/target0:0:0/0:0:0:0/block/sata1 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata2 -> ../devices/pci0000:00/0000:00:11.0/0000:02:03.0/ata2/host1/target1:0:0/1:0:0:0/block/sata2 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata3 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata32/host31/target31:0:0/31:0:0:0/block/sata3 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata4 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata33/host32/target32:0:0/32:0:0:0/block/sata4 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata5 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata34/host33/target33:0:0/33:0:0:0/block/sata5 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata6 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata35/host34/target34:0:0/34:0:0:0/block/sata6 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata7 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata36/host35/target35:0:0/35:0:0:0/block/sata7 tc@box:~$ lspci -tvnnq -[0000:00]-+-00.0 Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] +-01.0-[01]-- +-07.0 Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] +-07.1 Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] +-07.3 Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] +-07.7 VMware Virtual Machine Communication Interface [15ad:0740] +-0f.0 VMware SVGA II Adapter [15ad:0405] +-11.0-[02]--+-00.0 VMware USB1.1 UHCI Controller [15ad:0774] | +-01.0 VMware USB2 EHCI Controller [15ad:0770] | +-03.0 VMware SATA AHCI controller [15ad:07e0] | \-04.0 VMware SATA AHCI controller [15ad:07e0] +-15.0-[03]----00.0 Intel Corporation 82574L Gigabit Network Connection [8086:10d3] +-15.1-[04]-- pcie_root = "00:11.0,04.0"; ata_port = <0x31>; and pcie_root = "00:11.0,02:04.0"; ata_port = <0x31>; all not worked Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 22, 2022 Author Share #2948 Posted April 22, 2022 15 minutes ago, likeme said: How to modify my ds920p.dts ? lrwxrwxrwx 1 root root 0 Apr 22 2022 sata1 -> ../devices/pci0000:00/0000:00:11.0/0000:02:03.0/ata1/host0/target0:0:0/0:0:0:0/block/sata1 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata2 -> ../devices/pci0000:00/0000:00:11.0/0000:02:03.0/ata2/host1/target1:0:0/1:0:0:0/block/sata2 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata3 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata32/host31/target31:0:0/31:0:0:0/block/sata3 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata4 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata33/host32/target32:0:0/32:0:0:0/block/sata4 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata5 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata34/host33/target33:0:0/33:0:0:0/block/sata5 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata6 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata35/host34/target34:0:0/34:0:0:0/block/sata6 lrwxrwxrwx 1 root root 0 Apr 22 2022 sata7 -> ../devices/pci0000:00/0000:00:11.0/0000:02:04.0/ata36/host35/target35:0:0/35:0:0:0/block/sata7 tc@box:~$ lspci -tvnnq -[0000:00]-+-00.0 Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] +-01.0-[01]-- +-07.0 Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] +-07.1 Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] +-07.3 Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] +-07.7 VMware Virtual Machine Communication Interface [15ad:0740] +-0f.0 VMware SVGA II Adapter [15ad:0405] +-11.0-[02]--+-00.0 VMware USB1.1 UHCI Controller [15ad:0774] | +-01.0 VMware USB2 EHCI Controller [15ad:0770] | +-03.0 VMware SATA AHCI controller [15ad:07e0] | \-04.0 VMware SATA AHCI controller [15ad:07e0] +-15.0-[03]----00.0 Intel Corporation 82574L Gigabit Network Connection [8086:10d3] +-15.1-[04]-- pcie_root = "00:11.0,04.0"; ata_port = <0x31>; and pcie_root = "00:11.0,02:04.0"; ata_port = <0x31>; all not worked Safest way would always be to boot into DSM and check /sys/block/sata1/device/syno_block_info Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 22, 2022 Author Share #2949 Posted April 22, 2022 2 hours ago, romich7 said: I keep trying to build red-pill under Xen-Server. In rploader.sh, corrected the definition of disks in the expression $(mount | grep -i optional | grep cde | awk -F / '{print $3}' | uniq | cut -c 1-4) increased the length by one character (cut -c 1-3) was in the original version, made (cut -c 1-4). If it is possible to write an expression like (cut -c length($)-1) into the script, then tell me how to do it. As a result, when the script reaches the place where the .pat file is copied and unzipped, I get the error "cp: failed to preserve ownership for '/mnt/xvda3/auxfiles/ds3622xsp_42661.pat': Operation not permitted". What am I doing wrong? Not an issue. FAT file system does not support permission preservation. It’s just a warning that you can safely ignore 1 Quote Link to comment Share on other sites More sharing options...
cbacsro Posted April 22, 2022 Share #2950 Posted April 22, 2022 (edited) Hi guys, I'm a beginner. I downloaded tinycore-redpill.v0.4.6.img and write the img wiht rufus. I made 2 sticks. I made 2 sticks. For first time in my life I install and use PROXMOX. I try the obtion to passtrough the USB stick ( just for testing ) On March 10th I successfully generated, for test , RPTC bootloader DSM 7.0.1-42218, for DS DS1621 + and I applied patchdtc and it recognized all hdd (3 virtualVM Proxmox). Yesterday I tried to generate DSM 7.1.0-42621. I did not succeed. Error: [#] Checking runtime for required tools... [-] Couldn't find bspatch in your $PATH [#] Checking runtime for required tools... [ERR] [!] Some tools weren't available - install them first *** Process will exit *** FAILED : Loader creation failed check the output for any errors Today I write on USB stick again the img with Rufus. I tried to generate DSM 7.0.1 and DSM 7.1.0 bootloader for: DS3615xs, DS3622xs +, DS1621 +, but to no successl: tc@box:~$ ./rploader.sh build v1000-7.0.1-42218 ln: failed to create symbolic link '/home/tc/custom-module/auxfiles': Operation not permitted Rploader Version : 0.7.0.5 Loader source : https://github.com/jumkey/redpill-load.git Loader Branch : develop Redpill module source : https://github.com/jumkey/redpill-lkm.git : Redpill module branch : develop Extensions : redpill-dtb Extensions URL : "https://github.com/pocopico/redpill-load/raw/master/redpill-dtb/rpext-index.json" TOOLKIT_URL : https://sourceforge.net/projects/dsgpl/files/toolkit/DSM7.0/ds.v1000-7.0.dev.txz/download TOOLKIT_SHA : 6108f9f7b7f0a13ee985314aef9419303375ab7ded4112be991590339b66ecd1 SYNOKERNEL_URL : https://sourceforge.net/projects/dsgpl/files/Synology NAS GPL Source/25426branch/v1000-source/linux-4.4.x.txz/download SYNOKERNEL_SHA : d3e85eb80f16a83244fcae6016ab6783cd8ac55e3af2b4240455261396e1e1be COMPILE_METHOD : toolkit_dev TARGET_PLATFORM : v1000 TARGET_VERSION : 7.0.1 TARGET_REVISION : 42218 REDPILL_LKM_MAKE_TARGET : dev-v7 KERNEL_MAJOR : 4 MODULE_ALIAS_FILE : modules.alias.4.json SYNOMODEL : ds1621p_42218 MODEL : DS1621+ Local Cache Folder : /mnt/sdb3/auxfiles Checking Internet Access -> OK Checking if a newer version exists on the repo -> Version is current Redpill sources already downloaded, pulling latest Already up to date. Loader sources already downloaded, pulling latest Already up to date. No extra build option specified, using default <static> Using static compiled redpill extension Removing any old redpill.ko modules Looking for redpill for : ds1621p_42218 Getting file https://raw.githubusercontent.com/pocopico/rp-ext/master/redpill/releases/redpill-4.4.180plus-v1000.tgz Extracting module tar: redpill.ko: time stamp 2022-04-10 09:00:24 is 1770356.899771827 s in the future Getting file https://raw.githubusercontent.com/pocopico/rp-ext/master/redpill/src/check-redpill.sh Got redpill-linux-v4.4.180+.ko Testing modules.alias.4.json -> File OK ------------------------------------------------------------------------------------------------ It looks that you will need the following modules : parse error: Expected another key-value pair at line 1209, column 3 Found VGA Controller : pciid 1234d00001111 Required Extension : bochs_drm bochs_drm Searching for matching extension for bochs_drm parse error: Expected another key-value pair at line 1209, column 3 Found SATA Controller : pciid 8086d00002922 Required Extension : ahci Searching for matching extension for ahci parse error: Expected another key-value pair at line 1209, column 3 Found SATA Controller : pciid 8086d00002922 Required Extension : ahci Searching for matching extension for ahci Found Ethernet Interface : pciid 1af4d00001000 Required Extension : No matching extension ------------------------------------------------------------------------------------------------ Starting loader creation Found tinycore cache folder, linking to home/tc/custom-module Checking user_config.json : Done Entering redpill-load directory Removing bundled exts directories bsdiff binary was not downloaded Cache directory OK Want to use firmware files from /home/tc/custom-module/*.pat ? [yY/nN] : n Processing add_extensions entries found on custom_config.json file : redpill-dtb Adding extension "https://github.com/pocopico/redpill-load/raw/master/redpill-dtb/rpext-index.json" [#] Checking runtime for required tools... [OK] [#] Adding new extension from https://github.com/pocopico/redpill-load/raw/master/redpill-dtb/rpext-index.json... [#] Downloading remote file https://github.com/pocopico/redpill-load/raw/master/redpill-dtb/rpext-index.json to /home/tc/redpill-load/custom/extensions/_new_ext_index.tmp_json ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [OK] [#] ========================================== redpill-dtb ========================================== [#] Extension name: Device tree binary [#] Description: Create your own device tree binary [#] To get help visit: https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb [#] Extension preparer/packer: https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb [#] Software author: https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb [#] Update URL: https://github.com/pocopico/redpill-load/raw/master/redpill-dtb/rpext-index.json [#] Platforms supported: ds1621p_42218 ds920p_42661 ds1621p_42661 ds2422p_42661 ds2422p_42218 ds920p_42218 ds920p_42621 ds920p_42550 ds2422p_42621 ds1621p_42621 [#] ======================================================================================= Updating extension : redpill-dtb contents for model : ds1621p_42218 [#] Checking runtime for required tools... [OK] [#] Updating ds1621p_42218 platforms extensions... [#] Downloading remote file https://github.com/pocopico/redpill-load/raw/develop/redpill-dtb/recipes/universal.json to /home/tc/redpill-load/custom/extensions/_ext_new_rcp.tmp_json ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Filling-in newly downloaded recipe for extension redpill-dtb platform ds1621p_42218 [#] Downloading remote file https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb/releases/install_rd.sh to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/install_rd.sh ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/install_rd.sh file... [OK] [#] Downloading remote file https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb/releases/install.sh to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/install.sh ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/install.sh file... [OK] [#] Downloading remote file https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb/releases/model_ds920p.dtb to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds920p.dtb ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds920p.dtb file... [OK] [#] Downloading remote file https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb/releases/model_ds1621p.dtb to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds1621p.dtb ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds1621p.dtb file... [OK] [#] Downloading remote file https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb/releases/model_ds2422p.dtb to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds2422p.dtb ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds2422p.dtb file... [OK] [#] Downloading remote file https://github.com/jumkey/redpill-load/raw/develop/redpill-dtb/releases/dtc to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/dtc ###################################################################################################################################################################################### 100.0%###################################################################################################################################################################################### 100.0% [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/dtc file... [OK] [#] Successfully processed recipe for extension redpill-dtb platform ds1621p_42218 [#] Verifying /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/dtc file... [OK] Protocol spec without prior Class and Subclass spec at line 23281 Downloading dtc binary ###################################################################################################################################################################################### 100.0% dts file for ds1621p not found, trying to download ###################################################################################################################################################################################### 100.0% Found 1 disks and 0 nvme Collecting disk paths Found local disk sda with path 00:1e.0,01.0, adding into internal_slot 1 with portnumber 6 NO NVME disks found, returning Patching USB to include your loader. Loader found in 9-2 port Converting dts file : ds1621p.dts to dtb file : >ds1621p.dtb Copying patched dtb file ds1621p.dtb to /home/tc/redpill-load/custom/extensions/redpill-dtb/ds1621p_42218/model_ds1621p.dtb -> OK ! File copied and verified ! [#] Checking runtime for required tools... [-] Couldn't find bspatch in your $PATH [#] Checking runtime for required tools... [ERR] [!] Some tools weren't available - install them first *** Process will exit *** FAILED : Loader creation failed check the output for any errors Please help me! Thank you very much! Please try to write the image to USB stick and generate one DSM loader. Maybe I'm a little unskilled. Edited April 22, 2022 by cbacsro Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.