Spats Posted July 27, 2022 Share #201 Posted July 27, 2022 1 minute ago, pocopico said: What is the issue ? Sorry for got to add "No drives detected in DVA1622" Quote Link to comment Share on other sites More sharing options...
pocopico Posted July 27, 2022 Author Share #202 Posted July 27, 2022 (edited) 2 minutes ago, Spats said: Sorry for got to add "No drives detected in DVA1622" OK i see the problem .. please change your BIOS disk settings to SATA AHCI if thats possible. IDE is not supported. Edited July 27, 2022 by pocopico 1 Quote Link to comment Share on other sites More sharing options...
Spats Posted July 27, 2022 Share #203 Posted July 27, 2022 19 minutes ago, pocopico said: OK i see the problem .. please change your BIOS disk settings to SATA AHCI if thats possible. IDE is not supported. Thanks mate, changed all settings to AHCI that works ok, now i have another problem is that it "fails to install file. The file is probably corrupted" @57%. Dowloaded .Pat file from syno itself. Any ideas as to why this is happening?. Cheers Quote Link to comment Share on other sites More sharing options...
Orphée Posted July 27, 2022 Share #204 Posted July 27, 2022 Thanks mate, changed all settings to AHCI that works ok, now i have another problem is that it "fails to install file. The file is probably corrupted" @57%. Dowloaded .Pat file from syno itself. Any ideas as to why this is happening?. Cheers Serial logs, or it did not happen. 1 Quote Link to comment Share on other sites More sharing options...
Spats Posted July 27, 2022 Share #205 Posted July 27, 2022 @Orphée I don't understand bud, your quote Serial logs, or it did not happen. Unquote Please explain cheers Quote Link to comment Share on other sites More sharing options...
phone guy Posted July 27, 2022 Share #206 Posted July 27, 2022 He wants the serial output log 1 Quote Link to comment Share on other sites More sharing options...
Spats Posted July 27, 2022 Share #207 Posted July 27, 2022 Thanks @phone guy I thought that but how to give serial logs, running BareMetal but don't have means to give serial output tho. Quote Link to comment Share on other sites More sharing options...
phone guy Posted July 27, 2022 Share #208 Posted July 27, 2022 (edited) 13 minutes ago, Spats said: Thanks @phone guy I thought that but how to give serial logs, running BareMetal but don't have means to give serial output tho. Make sure you run ./rploader.sh identifyusb now to make sure usb is hidden. if you are doing bare metal you are most likely booting from usb. boot back to tinycore and either clean and start fresh by whatever means makes you comforable - rewrite usb, clean, whatever, be sure to run that command and build again. Theres a way to login in telnet to get the serial logs, but I have never done it... its <ip>:7681 user is root no pw if I remember right. or you can search for the directions, theyve been posted a bunch of times. otherwise clean and start again, the basic starter commands ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh serialgen <your platform here> ./rploader.sh identifyusb now ./rploader.sh satamap now ./rploader.sh ext <your platform here> add <pick ext/drivers from https://github.com/pocopico/rp-ext> ./rploader.sh build <your platform here> Good luck (sorry I cant be more help) Edited July 27, 2022 by phone guy 1 Quote Link to comment Share on other sites More sharing options...
Orphée Posted July 27, 2022 Share #209 Posted July 27, 2022 14 minutes ago, Spats said: Thanks @phone guy I thought that but how to give serial logs, running BareMetal but don't have means to give serial output tho. It is in french, but quite easy to understand/translate. 1 Quote Link to comment Share on other sites More sharing options...
sandro_66 Posted July 27, 2022 Share #210 Posted July 27, 2022 4 часа назад, Orphée сказал: 4 часа назад, sandro_66 сказал: Excuse me, do I understand you correctly that you managed to connect 16 sata hdd to dva1622? Physically, only 2 sata hdd can be connected to this device (if it were not Xpenology, but a real device). The storage manager also shows only 2 hdd bays. Or have I misunderstood you? There is nothing new here. Loaders are able to handle more than official Syno's since ... always ? A friend tried to install another additional disk (the third in a row), but it was not detected in DSM (you can see two disks that were before). The new hdd is working, before that it was installed on a Windows PC. I have arpl loader version 0.3a1. True, I did not rebuild the bootloader after adding a new disk. But as far as I know, satamap is not necessary in DVA1622, and arpl satamap is not used in the arpl bootloader itself. Quote Link to comment Share on other sites More sharing options...
Spats Posted July 27, 2022 Share #211 Posted July 27, 2022 1 hour ago, Orphée said: It is in french, but quite easy to understand/translate. Thanks @Orphée I dont have space in my pc, for a card but i am connected via <ip>:7681. So what commands do i need please, thanks Quote Link to comment Share on other sites More sharing options...
Spats Posted July 27, 2022 Share #212 Posted July 27, 2022 Anyone guys..... Quote Link to comment Share on other sites More sharing options...
dimammx Posted July 27, 2022 Share #213 Posted July 27, 2022 @SpatsOne of the suggested adapters in the article is USB, do you have a USB port available? Quote Link to comment Share on other sites More sharing options...
D_G_B Posted July 28, 2022 Share #214 Posted July 28, 2022 15 hours ago, sandro_66 said: I did not rebuild the bootloader after adding a new disk. But as far as I know, satamap is not necessary in DVA1622, and arpl satamap is not used in the arpl bootloader itself. Yes, satamap is not used for DVA1622... But the DeviceTree is built when the loader is built... Reboot your machine into "configure loader"... run .menu.sh, rebuild the loader and then boot the loader. This will rebuild your DeviceTree file and allow your additional drive to be visible to DSM... You are experiencing this because, unless your BIOS supports hotswap and it is enabled for all SATA ports, the DeviceTree builder will only see SATA ports that have a drive connected. If your motherboard supports hotswap and it is enabled when you build the loader, you will then not need to rebuild the loader when you add a drive. Quote Link to comment Share on other sites More sharing options...
spv4u1975 Posted July 28, 2022 Share #215 Posted July 28, 2022 Just some feedback on my trials. All bare metal and using the simple loader builder from the other thread, I've built before but this just makes it much so simple and is great work. All Bare Metal builds with 2 x 3GB drives set in SHR config, 6 x 1080p cameras on dual feed and 2 x DVA running. J3455-ITX with 8GB ram built and ran fine but slower to respond to commands but not so bad if your just leaving it in a corner to do the work on SSS HP Prodesk MT G4 i5 8GB ram - Ram much better built using a migration 2 DVA running and about 50% CPU being consumed HP Prodesk MT G4 i7-7700 12GB Ram - Like lightening and using 15% ram and CPU - Literally just swapped disks and USB and the thing booted but HW is almost identical to i5 model. So the i7-7000 obviously is more powerful but has the same graphics as the actual model but for £100 on eBay it has made life very simple, as a MT model (micro tower) it has plenty of space for 2 disks. NOTE: for the HP models the device works much better with a monitor attached or dummy connector, I remember some time ago in a Plex forum that for HW transcoding to work you had to have a screen attached otherwise the intel graphics would not work, but not sure if Synology have fixed that or an issue in DVA1622 Quote Link to comment Share on other sites More sharing options...
sandro_66 Posted July 28, 2022 Share #216 Posted July 28, 2022 Hello boys! Can you please tell me if it is possible to enable hardware video transcoding in Videostation or Emby on Xpenology assembly for dva1622? I have a motherboard with a J4125 processor and an integrated Intel UHD600 graphics card. Thank you! Quote Link to comment Share on other sites More sharing options...
SixthTangerine Posted July 28, 2022 Share #217 Posted July 28, 2022 2 hours ago, sandro_66 said: Hello boys! Can you please tell me if it is possible to enable hardware video transcoding in Videostation or Emby on Xpenology assembly for dva1622? I have a motherboard with a J4125 processor and an integrated Intel UHD600 graphics card. Thank you! Sure, the real dva1622 uses j4125 1 Quote Link to comment Share on other sites More sharing options...
merve04 Posted July 29, 2022 Share #218 Posted July 29, 2022 7 hours ago, SixthTangerine said: Sure, the real dva1622 uses j4125 Maybe it needs legit SN/Mac for it to work with video station? Not sure, I use plex and hw transcoding is working properly fine. 1 Quote Link to comment Share on other sites More sharing options...
Bullseye Posted July 29, 2022 Share #219 Posted July 29, 2022 Im playing with DVA1622 on VM with 4x 16GB HDDs and SHR1 i have just 16GB space ? what heppend ? Quote Link to comment Share on other sites More sharing options...
dimakv2014 Posted July 29, 2022 Share #220 Posted July 29, 2022 (edited) 2 часа назад, Bullseye сказал: Im playing with DVA1622 on VM with 4x 16GB HDDs and SHR1 i have just 16GB space ? what heppend ? Well if you have 4 hdd with 16gb I guess you created Raid1 pr 10, all 4 hdds act as a one. Go to hdd settings and choose raid0 if you want them 4 be available as separate drives Edited July 29, 2022 by dimakv2014 Quote Link to comment Share on other sites More sharing options...
SixthTangerine Posted July 29, 2022 Share #221 Posted July 29, 2022 (edited) On 7/28/2022 at 3:56 PM, spv4u1975 said: Just some feedback on my trials. All bare metal and using the simple loader builder from the other thread, I've built before but this just makes it much so simple and is great work. All Bare Metal builds with 2 x 3GB drives set in SHR config, 6 x 1080p cameras on dual feed and 2 x DVA running. J3455-ITX with 8GB ram built and ran fine but slower to respond to commands but not so bad if your just leaving it in a corner to do the work on SSS HP Prodesk MT G4 i5 8GB ram - Ram much better built using a migration 2 DVA running and about 50% CPU being consumed HP Prodesk MT G4 i7-7700 12GB Ram - Like lightening and using 15% ram and CPU - Literally just swapped disks and USB and the thing booted but HW is almost identical to i5 model. So the i7-7000 obviously is more powerful but has the same graphics as the actual model but for £100 on eBay it has made life very simple, as a MT model (micro tower) it has plenty of space for 2 disks. NOTE: for the HP models the device works much better with a monitor attached or dummy connector, I remember some time ago in a Plex forum that for HW transcoding to work you had to have a screen attached otherwise the intel graphics would not work, but not sure if Synology have fixed that or an issue in DVA1622 Are these 3 HW of yours worked well with monitor under dva1622? Edited July 29, 2022 by SixthTangerine Quote Link to comment Share on other sites More sharing options...
Bullseye Posted August 2, 2022 Share #222 Posted August 2, 2022 The most common error that i have in console is: [ 375.353260] EXT4-fs (md0): couldn't mount as ext3 due to feature incompatibilities [ 379.375233] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) (drives are clear, without any partition) Quote Link to comment Share on other sites More sharing options...
spv4u1975 Posted August 2, 2022 Share #223 Posted August 2, 2022 (edited) On 7/29/2022 at 10:17 AM, SixthTangerine said: Are these 3 HW of yours worked well with monitor under dva1622? I never have local monitor, on all of them I inserted a dummy monitor plug so the PC thinks a monitor is attached and then placed it away on top of a cupboard, I connect over IP and installed the SSS application on my local desktop and laptop for video viewing. Edited August 2, 2022 by spv4u1975 Quote Link to comment Share on other sites More sharing options...
spv4u1975 Posted August 2, 2022 Share #224 Posted August 2, 2022 (edited) On 7/27/2022 at 8:33 AM, dimammx said: Do we know what are requirements for AI to work? We know Intel® UHD Graphics 600 works, but how about HD 600, UHD620 or HD620. Trying to find some affordable surplus desktops to support AI Get yourself on eBay and look for HP Prodesk G4 or G5 models (they do a desktop and and MT (MicroTower), I just bagged a MT with a i7-7700, 12GB RAM and 1TB HDD for £100 (i got a good deal) and this model flies on it, has same graphics as well I believe. Edited August 2, 2022 by spv4u1975 2 Quote Link to comment Share on other sites More sharing options...
majk10 Posted August 2, 2022 Share #225 Posted August 2, 2022 Do you have a problem with enabling push notifications in Ds cam dva1622? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.