Elpee Posted November 1, 2016 Share #926 Posted November 1, 2016 Hey guys, For those who are asking about the setting for "SataPortMap=" I many times have asked about how to set the value for SataPortMap, but I received no responses and I understand it's hard to tell. After a couple days with several experiments, here is the experience I want to share. I built my new DSM 6.0 Nas on the mobo Asrock QC5000-itx that has 4 onboard sata ports. I also attached anothe Syba sata card that has 4 ports. So, totally I will have 8 sata ports to have 8 HDDs connected. And as a normal thinking, I would set SataPortMap=44, right? Wrong! My first experience is before you ask please watch, watch, and watch. When I check 4 sata ports on the mobo, I found it says SATA3_A0, SATA3_A1, SATA3_1, and SATA3_A2 see the picture (instead of SATA1, 2, 3, and 4 as usual) that drew my attention with a question why? Searched around I quickly found out 2 ports are controlled by AMD onboard chipset and the other two are controlled by ASMedia ASM1061. The next experience is but which chipset controls SATA3_A0, SATA3_A1, and which one controls SATA3_1, and SATA3_A2 I had no idea either. And therefore what would I set for SataPortMap? SataPortMap=224, SataPortMap=242, or SataPortMap=422? To save your time, please write down the serial number of each your HDDs with located port number. First, let's set SataPortMap=224, of course log on bios and make sure it recognizes all your HDDs there. Then once log on DSM, check S.M.A.R.T for serial numbers to find out which HDDs are seen together with port numbers. Trust me, now you understand your system and can set value for the grub parameter SataPortMap= correctly. Good luck. Quote Link to comment Share on other sites More sharing options...
rzimin Posted November 1, 2016 Share #927 Posted November 1, 2016 Trying latest v1.0 image burned with disk32imager and unable to boot on baremetal non uefi bios at all. Just showing me the blank screen with blinking underscore. Though loads fine on uefi one. Any ideas? Quote Link to comment Share on other sites More sharing options...
Lionel0676 Posted November 1, 2016 Share #928 Posted November 1, 2016 Thanks for the team. I have migrate my N54L, and all is look good. Quote Link to comment Share on other sites More sharing options...
Moonlight Posted November 1, 2016 Share #929 Posted November 1, 2016 Everything works with new V1 loader... Except for 2 nic's. I to am experiencing this issue. If you set just mac1=, everything is fine and dsm reports both nics (although the second one is obviously inaccessible remotely), but as soon as set mac2= is added, both connections quit. That's a pretty big problem. Any thoughts? I want my 10G connection, pls hlp When you added the mac2= did you also try editing the synoinfo.conf file to manually set it as active? It should then show under Hardware and Power with a check box for WOL. Maybe you can use that to see if the card is accessible on the network? The network card shows up in Network, and it shows LAN2. I don't see anything in synoinfo.conf that says it's disabled. I can't change anything in synoinfo after adding mac2 because as soon as I add mac2 I lose access to everything. Quote Link to comment Share on other sites More sharing options...
billa786165 Posted November 1, 2016 Share #930 Posted November 1, 2016 hello everyone but i am facing an error at boot it is show me serial is'nt foung. press any key to continue. i am trying to run it on my surface pro 3. please help me. Quote Link to comment Share on other sites More sharing options...
quicknick Posted November 1, 2016 Share #931 Posted November 1, 2016 hello everyone but i am facing an error at boot it is show me serial is'nt foung. press any key to continue. i am trying to run it on my surface pro 3. please help me. This is because you don't have a serial port, so serial is disabled. You have to use http://find.synology.com or find the IP on your router. Sent from my SM-N920T using Tapatalk Quote Link to comment Share on other sites More sharing options...
billa786165 Posted November 1, 2016 Share #932 Posted November 1, 2016 Do I have to connect through eathernet? Sent from my SM-G925F using Tapatalk Quote Link to comment Share on other sites More sharing options...
trublu Posted November 2, 2016 Share #933 Posted November 2, 2016 I get to this screen but can't connect to or find dsm using synology assistant. Any pointers from anyone? http://imgur.com/a/c8Ysx Quote Link to comment Share on other sites More sharing options...
djelusion Posted November 2, 2016 Share #934 Posted November 2, 2016 i got the same response but I cant re test as its going on 1 week repairing 1tb which is currently @ 45%.. maybe by xmas or thanksgiving will I be able to test this out and try the find.synology.com but like i said before i got to the booting the kernel part i didnt attempt to find.syno.com I assumed it was *broken* but through the response of others I have hope it might work if this fucking repair disk ever finishes... Quote Link to comment Share on other sites More sharing options...
trublu Posted November 2, 2016 Share #935 Posted November 2, 2016 i got the same response but I cant re test as its going on 1 week repairing 1tb which is currently @ 45%.. maybe by xmas or thanksgiving will I be able to test this out and try the find.synology.com but like i said before i got to the booting the kernel part i didnt attempt to find.syno.com I assumed it was *broken* but through the response of others I have hope it might work if this fucking repair disk ever finishes... How can you tell if it's repairing or doing anything at all? Quote Link to comment Share on other sites More sharing options...
sbafs Posted November 2, 2016 Share #936 Posted November 2, 2016 You have managed to use the 6 disks on HP n36l, N40L or n54l? With sataportmap =? Thank Quote Link to comment Share on other sites More sharing options...
romain081 Posted November 2, 2016 Share #937 Posted November 2, 2016 Hello everyone ! (I'm sorry if my english speaking is very bad >< I'm a french guy ^^") Another problem that i encounter ><" DHCP on my NAS. At the beginning I want to make a VM with PHPVirtualBox but it's not supported at this time. After that I try to get a docker with isc-dhcp-server and bind9. But i can't redirect the container port 67 (DHCP port) to the port 67 of my NAS, because there is already a service using this port. So I try to use the DHCP server already come with DSM, I manage to make all parameters correct. But when I click on "Activate DHCP server" it doesn't do anything. It seems that it doesn't want to start Thanks, Romain Quote Link to comment Share on other sites More sharing options...
ema Posted November 2, 2016 Share #938 Posted November 2, 2016 11/2: as I promised, here is v1.01, download link is the same as v1.0 This update contains nothing fancy, mainly for inner peace, Plus, I revert megaraid_sas mpt3sas to old version. Hi jun, many thanks for this great release. It works (again) without problem on my n36l (3x2tb). Any plans to release a 916+ version? I've a N3150 board, it will be nice to test hw acceleration with videostation or plex. Thanks! ema Quote Link to comment Share on other sites More sharing options...
rzimin Posted November 2, 2016 Share #939 Posted November 2, 2016 Greetings, I've tried updated 1.1 version and still unable to boot on non UEFI motherboards, baremetal. Can anyone help with this? Quote Link to comment Share on other sites More sharing options...
jcdln Posted November 2, 2016 Share #940 Posted November 2, 2016 Greetings, I've tried updated 1.1 version and still unable to boot on non UEFI motherboards, baremetal. Can anyone help with this? Same problem whereas arcao's loader works on my mobo. Quote Link to comment Share on other sites More sharing options...
F5BJR Posted November 2, 2016 Share #941 Posted November 2, 2016 With old boot versions no problem ( RTL8201 ) same motherboard GA-M61PME-S2P This motherboard run also with DS214Play 32 bits boot With new dsm 6 loader no nic card, why no driver ? Quote Link to comment Share on other sites More sharing options...
trublu Posted November 2, 2016 Share #942 Posted November 2, 2016 I'm still stuck on the "Booting the kernel ..." with no DSM access screen after leaving it over night. I've checked my router/switch and the server doesn't have an assigned ip address. The steps I took were to modify the VID and PID. I also added one of my mac actual addresses and updated the SN number (not a matched pair since I don't need QC). Hardware: SUPERMICRO MBD-A1SAi-2750F-O and LSI SAS 9211-8i Can anyone tell me if i got something wrong or missed something. Quote Link to comment Share on other sites More sharing options...
jjLDN Posted November 2, 2016 Share #943 Posted November 2, 2016 Hello everybody, Big thanks to @jun, @Trantor and @arcao for their hard work. Just the quick one Did anyone managed to install DSM 6.1 Beta successfully using this patcher? Cheers Quote Link to comment Share on other sites More sharing options...
Martino Posted November 2, 2016 Share #944 Posted November 2, 2016 So i tried to boot on my server with C2750D4I here my report it boots but nic seems to not work (nothing appear on my network) Is Intel® i210 driver in ? if yes, seems to not work Quote Link to comment Share on other sites More sharing options...
rzimin Posted November 2, 2016 Share #945 Posted November 2, 2016 Greetings, I've tried updated 1.1 version and still unable to boot on non UEFI motherboards, baremetal. Can anyone help with this? Same problem whereas arcao's loader works on my mobo. Do you mean jun-intel-baremetal-hybrid-uefibios-arcao-v2.zip from v2 (deprecated) folder? Because unable to run even with this case. I hope jun can take a look... Quote Link to comment Share on other sites More sharing options...
Guest Posted November 2, 2016 Share #946 Posted November 2, 2016 I tried to import the .ovf from DS3615xs 6.0.2 Jun's Mod V1.01 to my ESXi 6u2 server, but i got a 'Failed to deploy' message (IOError). I have downloaded the .zip again (maybe it was corrupt), but i got the same error. How can i get it working ? Quote Link to comment Share on other sites More sharing options...
Eduardo Posted November 2, 2016 Share #947 Posted November 2, 2016 Hey guys, For those who are asking about the setting for "SataPortMap=" I many times have asked about how to set the value for SataPortMap, but I received no responses and I understand it's hard to tell. After a couple days with several experiments, here is the experience I want to share. I built my new DSM 6.0 Nas on the mobo Asrock QC5000-itx that has 4 onboard sata ports. I also attached anothe Syba sata card that has 4 ports. So, totally I will have 8 sata ports to have 8 HDDs connected. And as a normal thinking, I would set SataPortMap=44, right? Wrong! My first experience is before you ask please watch, watch, and watch. When I check 4 sata ports on the mobo, I found it says SATA3_A0, SATA3_A1, SATA3_1, and SATA3_A2 see the picture (instead of SATA1, 2, 3, and 4 as usual) that drew my attention with a question why? Searched around I quickly found out 2 ports are controlled by AMD onboard chipset and the other two are controlled by ASMedia ASM1061. Watch, watch and watch or simply read the f***** manual ftp://europe.asrock.com/Manual/QC5000-ITXPH.pdf. Pages 3,6,7, 42. Please, report your conclusion. I have this mobo too. Not running XPEnology though. Quote Link to comment Share on other sites More sharing options...
Elpee Posted November 2, 2016 Share #948 Posted November 2, 2016 Watch, watch and watch or simply read the f***** manual ftp://europe.asrock.com/Manual/QC5000-ITXPH.pdf. Pages 3,6,7, 42. Please, report your conclusion. I have this mobo too. Not running XPEnology though. Good catch, but most people they're lazy to read f**** manual. Can you check manual and help people who currently get stuck on HP n54l with 6HDDS? My final setting is 242. Quote Link to comment Share on other sites More sharing options...
sbafs Posted November 2, 2016 Share #949 Posted November 2, 2016 Watch, watch and watch or simply read the f***** manual ftp://europe.asrock.com/Manual/QC5000-ITXPH.pdf. Pages 3,6,7, 42. Please, report your conclusion. I have this mobo too. Not running XPEnology though. Good catch, but most people they're lazy to read f**** manual. Can you check manual and help people who currently get stuck on HP n54l with 6HDDS? My final setting is 242. "sataportmap=242" is ok with n54l with 6 disks? Quote Link to comment Share on other sites More sharing options...
NeoID Posted November 2, 2016 Share #950 Posted November 2, 2016 I tried to import the .ovf from DS3615xs 6.0.2 Jun's Mod V1.01 to my ESXi 6u2 server, but i got a 'Failed to deploy' message (IOError). I have downloaded the .zip again (maybe it was corrupt), but i got the same error.How can i get it working ? Same issue here. Also can't hide the synoboot image from the list of disks if I create the VM manually. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.