ema

For a better result I will make the following change: - add a sata controller and connect hdd 1 (xpe.vmdk) to it on port sata0:0 - move hdd2 (xpe_1.vmdk) to scsi controller 0 port 0 and remove scsi controller 1 In this way you will see in DSM only data disk and not the boot disk with state "not initialised" Ciao ema

I agree with @hpk Microserver gen8 gt1610t baremetal fan 12-15% ciao ema

I installed it on esxi 6.5 just for testing... here there's not /dev/dri/card0 Ciao ema Execute the command: lsmod ash-4.3# lsmod | grep card ash-4.3# ash-4.3# lsmod Module Size Used by cifs 246536 2 udf 81376 0 isofs 32127 0 loop 17423 0 iscsi_target_mod 220762 1 target_core_ep 48756 2 target_core_file 29955 1 target_core_iblock 14240 1 target_core_mod 366535 13 target_core_iblock,iscsi_target_mod,target_core_ep,target_core_file syno_

I installed it on esxi 6.5 just for testing... here there's not /dev/dri/card0 Ciao ema

No... ciao ema

+1 ciao ema

Hi guys... Here's a version working on DSM 6.1 amsHelper >> no change, it's the same hpilo.ko >> recompiled for DSM 6.1 https://mega.nz/#!R8dUhDJb!dyYEVSsrWSohPfU5O7Uxo-GisuMKZPZbG4HbeiIeHk0 Ciao ema

Do you have any info on getting that to work? I tried it the other day and failed, so assumed it wasn't supported by XPE. Reboot your gen8 and enter bios (F9). If I remeber well you must disable BIOS serial console, because if you don't do it, when you launch VSP you will see gen8's bios console... Select "BIOS serial console & EMS" >> "BIOS Serial console port" and disable it. Now go to "System Options" >> "Serial Port Options" >> "Virtual Serial Port" >> I have enabled "COM1;IRQ4;3F8h-3FFh" Now exit Bios utility and reboot. Be sure to enable SSH access i

HP Gen8 with integrated dual nic Upgrade is working but no network after reboot... I connect to my Gen8 with iLO VSP (iLO Virtual Serial Port) and I found that there are 2 file missing from /lib/modules after upgrade: libphy.ko and tg3.ko I have found these two files under /lib/modules/update so I copied them under /lib/modules (don't forget to chmod 644 them) and reboot... now network is working again. I think, as Jun's said, there's something related to update script to fix... but, as other said, clean install work. Ciao ema

Io ho utilizzato 2 x 6tb wd red su un n36l... per cui penso che funzionino senza problemi anche sul tuo... ciao ema

ash-4.3# ps ax | grep amsHelper 14287 ? S 0:42 /sbin/amsHelper -I0 -M1 5 14 16 18 23 99 ash-4.3# lsmod | grep hpilo hpilo 6734 2 image share Ciao ema

Hi! I just updated my test gen8 to update 7 to check what you said, but I can confirm that everything works as with previous versions. So check in previous post what's the correct way to use the driver (hpilo.ko) and the bin (amsHelper). ciao ema

Hi quicknick, awesome work!!! There's any chance to see a DS916 version with hardware acceleration for video's transcoding? Ciao ema

Working AMS and iLO driver for dsm 6 are here http://xpenology.com/forum/viewtopic.php?f=2&t=7640&start=10#p78810 Ciao ema

Look here for how to fake the fan signal, etc.. http://homeservershow.com/forums/index.php?/topic/7294-faking-the-fan-signal/page-1 Ciao ema