1450 Posted October 16, 2016 Share #576 Posted October 16, 2016 I can't post a log as there is no SSH access however the N54L appears to freeze during/after PCI enumeration which would explain why nobody can find the device on Synology Assistant or on their network. I was looking for a core dump or something to pinpoint where it was failing but nothing obvious stood out, the below is all I found out. Last messages in the boot process are similar to the below: [ 0.193677] NET: Registered protocol family 2 [ 0.194016] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.194303] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.194726] TCP: Hash tables configured (established 65536 bind 65536) [ 0.194791] TCP: reno registered [ 0.194799] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.194869] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.194985] NET: Registered protocol family 1 Prints a couple lines like: [ 0.193611] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff] [ 0.193612] pci_bus 0000:02: resource 1 [mem 0xfe600000-0xfe7fffff] [ 0.193613] pci_bus 0000:02: resource 2 [mem 0xfe000000-0xfe1fffff 64bit pref] then freezes The synology kernel do not have AMD CPU support compiled in, so it is expected that AMD box can not run properly. Adding support requires a full recompilation from source or some non-trivial patch to the synology kernel, both solution has its own difficulties. I personally does not have the hardware, so It may be a long wait before something positive happens. Might be worth putting a big notice in the original thread so N54L/AMD users know this as originally people suspected that it was just due to missing network card drivers as opposed to the system not booting, Quote Link to comment Share on other sites More sharing options...
jun Posted October 16, 2016 Author Share #577 Posted October 16, 2016 Might be worth putting a big notice in the original thread so N54L/AMD users know this as originally people suspected that it was just due to missing network card drivers as opposed to the system not booting, To my surprise, I've seen report that AMD E-350 box works. Quote Link to comment Share on other sites More sharing options...
redskies Posted October 16, 2016 Share #578 Posted October 16, 2016 I have Xpenology running on Esxi6 DSM 5.2-5644 update 5. I have a 16 gb vmdisk for apps (Scsi1 controller) seen as Volume 1 and PCI SATA controller ASM1062 with 1TB hard drive for data seen as Volume 2. I have tried a test with the DSM6 on ESxi6 and it works. How do I upgrade from the previous bootloader to this new one ? Can some help me with configuration details for the volume 1 and volume 2. TIA Quote Link to comment Share on other sites More sharing options...
viumden Posted October 17, 2016 Share #579 Posted October 17, 2016 Anybody find way to make the loader adapted to run DSM6 in Hyper V? Quote Link to comment Share on other sites More sharing options...
stuhad Posted October 17, 2016 Share #580 Posted October 17, 2016 Hi I've managed to edit the S/N and MAC in grub.cfg, the changes seem to keep after a reboot, however when trying to set up quickconnect I still get error: the system failed to perform the requested operation, there is an unknown error login Have I done something wrong? Quote Link to comment Share on other sites More sharing options...
Ticariocman Posted October 17, 2016 Share #581 Posted October 17, 2016 Looks like people still abuse QC... Quote Link to comment Share on other sites More sharing options...
dynax Posted October 17, 2016 Share #582 Posted October 17, 2016 Looks like people still abuse QC... I agree. This is away to shoot ourselves in the foot. Synology can tell the fake S/N and MAC combination and where those come from (while using QC). When they realize the "market lost", they'll encrypt the DSM better. There are many free DNS services that works faster than QC. Quote Link to comment Share on other sites More sharing options...
tdutrieux Posted October 17, 2016 Share #583 Posted October 17, 2016 Hello, Anyone managed to install DSM6 in ESXi with a LSI8211 configured in pci passthrough ? I tried myself but the disks connected to the LSI are not detected. Best regards, TitiD Quote Link to comment Share on other sites More sharing options...
quicknick Posted October 17, 2016 Share #584 Posted October 17, 2016 Hello, Anyone managed to install DSM6 in ESXi with a LSI8211 configured in pci passthrough ? I tried myself but the disks connected to the LSI are not detected. Best regards, TitiD @everyone on this thread, No. No LSI 2008 based controllers will work with this loader. This will not be possible until patched kernel and loader is released. I have diverted my time making a configuration tool for everyone (because I got sick of cleaning up the kernel), but will resume working on the kernel soon. Quote Link to comment Share on other sites More sharing options...
Polanskiman Posted October 18, 2016 Share #585 Posted October 18, 2016 (edited) Hi I've managed to edit the S/N and MAC in grub.cfg, the changes seem to keep after a reboot, however when trying to set up quickconnect I still get error:the system failed to perform the requested operation, there is an unknown error login Have I done something wrong? Looks like people still abuse QC... I agree. This is away to shoot ourselves in the foot. Synology can tell the fake S/N and MAC combination and where those come from (while using QC). When they realize the "market lost", they'll encrypt the DSM better. There are many free DNS services that works faster than QC. I am not sure what is so hard to comprehend about QC and why some people are desperately trying to abuse Synology and their services. I think some people who are trying to do that don't even understand what QC is for and why they are trying to do it. That's the only explanation I can find. Using Xpenology loaders to circumvent Synology's hardware restrictions leads to some features not being 100% functional. QC is one of them but there is a very simple way to get around it. As said above: use a DDNS. It is part of Synology features and you can even use custom ddns configs. It's really not that complicated and it is located just below the QuickConnect tab and it's called External Access. Both have the same functions. One being a service provided by Synology. That's about it. See below: Edited October 18, 2016 by Guest Quote Link to comment Share on other sites More sharing options...
CtrlAltDel Posted October 18, 2016 Share #586 Posted October 18, 2016 (edited) Please, is there any way to make a loader that uses a version that supports SHR natively?Maybe DS1815+ or something like that? I am absolutely willing to test/work on to help, but I am no big linux-whiz I'm afraid... You dont need a DS1815+ for SHR support just edit /etc.defaults/synoinfo.conf comment out/delete supportraidgroup="yes" then add support_syno_hybrid_raid="yes" press F5 on you web browser Thanks Jun, I can confirm this works for a fresh bearmetal installation on a Gen8 with a raw drive. The disk group created as shr raid with a btrfs file system and the system is now busy verifying the drive. I cocked up on my first run at it...I made the mistake of editing the file in etc when I should have been in etc.defaults. Edit: Update, added a new disk and expanded the disk group successfully (it's still busy expanding and checking parity right now). The disk group/volume is running in shr with btrfs on 2 x WD 4TB drives. Edited October 18, 2016 by Guest Quote Link to comment Share on other sites More sharing options...
bdby99 Posted October 18, 2016 Share #587 Posted October 18, 2016 Hi I am quite new to this. Have a Hp Gen8 Microserver with xpenoboot running dsm 5.2 5967 (baremetal no VM). There were mixed informations so I ask you guys. Is it possible to install baremetal DSM 6 to my microserver using the boot image the first page? Some suggests its not possible because lack of UEFI support. Thanks for your answer. Quote Link to comment Share on other sites More sharing options...
Polanskiman Posted October 18, 2016 Share #588 Posted October 18, 2016 (edited) Hi I am quite new to this. Have a Hp Gen8 Microserver with xpenoboot running dsm 5.2 5967 (baremetal no VM). There were mixed informations so I ask you guys. Is it possible to install baremetal DSM 6 to my microserver using the boot image the first page? Some suggests its not possible because lack of UEFI support. Thanks for your answer. I think you need to read the thread carefully. Your answer is there. Edited October 18, 2016 by Guest Quote Link to comment Share on other sites More sharing options...
stuhad Posted October 18, 2016 Share #589 Posted October 18, 2016 uh sorry guys I was actually just using qc as a test to see if I got the serial number and mac address working using the guides on this forum, as I assumed that was the whole reason for doing it (as most other things seem to work without altering the serial number or mac) I actually already run another DDNS service with a cname setup on my own domain, I didn't meant to "shoot anyone in the foot" Is it just to get wake on lan working that you edit the serial and mac address? Quote Link to comment Share on other sites More sharing options...
meimeiriver Posted October 18, 2016 Share #590 Posted October 18, 2016 Is anyone using the latest DSM Hyper Backup with Amazon Drive?! All I'm getting is a blank screen when I initiate the Hyper Backup and connect to the cloud. Quote Link to comment Share on other sites More sharing options...
Hostilian Posted October 18, 2016 Share #591 Posted October 18, 2016 Looks like people still abuse QC... Totally agree.. Use QC without a real Synology and Synology will be sure to make tweaks to their code that will close down (or severely limit) this little project.. ie.. Don't do it.. There are plenty of alternatives that won't screw this up for everyone.. #H Quote Link to comment Share on other sites More sharing options...
Ziomalski Posted October 18, 2016 Share #592 Posted October 18, 2016 @everyone on this thread, No. No LSI 2008 based controllers will work with this loader. This will not be possible until patched kernel and loader is released. I have diverted my time making a configuration tool for everyone (because I got sick of cleaning up the kernel), but will resume working on the kernel soon. Thanks quicknick for the update and your hard work. I think there are many of us patiently awaiting the LSI 2008 kernel patch. I installed xpeno5.2 for the time being while i'm waiting. Quote Link to comment Share on other sites More sharing options...
tigs Posted October 18, 2016 Share #593 Posted October 18, 2016 To clarify, I started trying out the xpenology only a few months back and only started to play with qc in this dsm6, in the last week or two. I never needed the service. I don't really know what this is all about, until I found out that it could be useful for Ds cloud to back up iphone. I have yet to sort it out how. I is not working as I expected it to ( I would want it backup my iphone, but not necessarily sync, I want the files stay in the NAS even after they are being deleted from the phone). That is not the case, therefore it really has no use for me. However, this is not the reason I am stopping using it. Thank those who made me become aware that this is a mis-use of Synology service. I have no intention to harm the community, the project and Synology. However, I don like the rheteric of how thi mesage is being conveyed to people like me. I f offended and mis-characterised. It would be more constructive if the messages are less person-oriented. This does not mean I am condoning myself. A couple of technical questions. I am not a computer guy at all. 1, I have difficulty configuring the "external access" function as someone pointed out. I have a pfsense box with VPN service running. When I try to set up t router through "external access", it always tells me something like "I have two routers in the network". If I turn off the VPN, it seems to work. Anyway I can set it up with VPN running? 2, if I use the serial and mac address from an old Synology box, would that be okay? Thanks Quote Link to comment Share on other sites More sharing options...
dynax Posted October 18, 2016 Share #594 Posted October 18, 2016 To clarify, I started trying out the xpenology only a few months back and only started to play with qc in this dsm6, in the last week or two. I never needed the service. I don't really know what this is all about, until I found out that it could be useful for Ds cloud to back up iphone. I have yet to sort it out how. I is not working as I expected it to ( I would want it backup my iphone, but not necessarily sync, I want the files stay in the NAS even after they are being deleted from the phone). That is not the case, therefore it really has no use for me. However, this is not the reason I am stopping using it. Thank those who made me become aware that this is a mis-use of Synology service. I have no intention to harm the community, the project and Synology. However, I don like the rheteric of how thi mesage is being conveyed to people like me. I f offended and mis-characterised. It would be more constructive if the messages are less person-oriented. This does not mean I am condoning myself. A couple of technical questions. I am not a computer guy at all. 1, I have difficulty configuring the "external access" function as someone pointed out. I have a pfsense box with VPN service running. When I try to set up t router through "external access", it always tells me something like "I have two routers in the network". If I turn off the VPN, it seems to work. Anyway I can set it up with VPN running? 2, if I use the serial and mac address from an old Synology box, would that be okay? Thanks You can definitely do what you want with DS cloud app on iPhone w/o QC. DS Cloud listens to port 6690. On your router, you need to open this port to your Xpenology IP address. You can then just use many of the free DDNS service to link you DS Cloud App back to Xpenology. On your iPhone DS cloud app, click on the first ICON "Cloud Station". You should see the folder that you picked for "sync". Click on the (!) on the right of that folder name. Under Sync direction, select "Upload only". Now, after upload your photo to your Xpenology, you can delete those on the iPhone and stuffs on the Xpenology remain. Technically speaking, there's nothing illegal/wrong with Xpenology project since it's based on opened source codes. Synology can't stop Xpenology if they wanted to. Quick Connect is a Synology service licensed only for their hardware's. Synology can easily make the apps (not DSM itself but the apps within it) stop working if detected a non-genuine MAC/SN from their data base. All they need to do is delay their release of the source code for a few years and the project will die eventually (or they can just encrypt it better). For (1), I don't quite understand your question. You have pfsense box that provides VPN server and you also have VPN server turned on in Xpenology? The option for "Router Configuration" in External Access is just a fancy way to open port in your router, it won't work if it sees 2 routers on your network. You can open port manually. When people talk about "External access" they typically mean the first tab "DDNS" setup. That's where you do your setup to replace QC. For (2) if you have a genuine Synology box, you can use its MAC/SN. in fact, a few years ago (before the xls file became public), many ppl bought broken Synology boxes just for the valid MAC/SN. Quote Link to comment Share on other sites More sharing options...
tigs Posted October 18, 2016 Share #595 Posted October 18, 2016 You can definitely do what you want with DS cloud app on iPhone w/o QC. DS Cloud listens to port 6690. On your router, you need to open this port to your Xpenology IP address. You can then just use many of the free DDNS service to link you DS Cloud App back to Xpenology. On your iPhone DS cloud app, click on the first ICON "Cloud Station". You should see the folder that you picked for "sync". Click on the (!) on the right of that folder name. Under Sync direction, select "Upload only". Now, after upload your photo to your Xpenology, you can delete those on the iPhone and stuffs on the Xpenology remain. Technically speaking, there's nothing illegal/wrong with Xpenology project since it's based on opened source codes. Synology can't stop Xpenology if they wanted to. Quick Connect is a Synology service licensed only for their hardware's. Synology can easily make the apps (not DSM itself but the apps within it) stop working if detected a non-genuine MAC/SN from their data base. All they need to do is delay their release of the source code for a few years and the project will die eventually (or they can just encrypt it better). For (1), I don't quite understand your question. You have pfsense box that provides VPN server and you also have VPN server turned on in Xpenology? The option for "Router Configuration" in External Access is just a fancy way to open port in your router, it won't work if it sees 2 routers on your network. You can open port manually. When people talk about "External access" they typically mean the first tab "DDNS" setup. That's where you do your setup to replace QC. For (2) if you have a genuine Synology box, you can use its MAC/SN. in fact, a few years ago (before the xls file became public), many ppl bought broken Synology boxes just for the valid MAC/SN. Thanks for the quick reply. I mistated. I was trying to setup my wife's iphone. It has not worked yet. the DS cloud app for iphone does not sync with DSM at all. I tried my blackberry, it worked but it deletes the files on the NAS whenever i deleted from my phone. This is not what I wanted. I dont need the back up at all> I was just trying to experiment if i can get this to work first. I have not tried the DS photo on blackberry. The ds photo on iphone does not sync either. I basically gave up the experiment. Sorry for the confusion. My pfsense box was setup to use an VPN service provider, like airvpn, etc. It is not a vpn server, it is a client. No VPN was setup in the synology box. the NO-IP ddns service was set up in the pfsense router, not in the NAS. There is also an entry of DDNS under synology automatically generated when I setup the QC. i guess I can safely delete that. I would like the router to handle the DDNS. by the way, I don't see the (!) as you indicated. I am using a lame version of android ds cloud, because it is blackbery. Quote Link to comment Share on other sites More sharing options...
meimeiriver Posted October 18, 2016 Share #596 Posted October 18, 2016 Is anyone using the latest DSM Hyper Backup with Amazon Drive?! All I'm getting is a blank screen when I initiate the Hyper Backup and connect to the cloud. Anyone have an answer to this, btw? Quote Link to comment Share on other sites More sharing options...
dynax Posted October 19, 2016 Share #597 Posted October 19, 2016 Is anyone using the latest DSM Hyper Backup with Amazon Drive?! All I'm getting is a blank screen when I initiate the Hyper Backup and connect to the cloud. Anyone have an answer to this, btw? At which step do you have a blank screen? If I click on Hyper Backup, it launches backup Wizard. I then can select S3 then [Next] and a backup destination settings opened up. I don't have the keys needed to go further. Up until that point, it seems to work fine on my end. Quote Link to comment Share on other sites More sharing options...
Polanskiman Posted October 19, 2016 Share #598 Posted October 19, 2016 Is anyone using the latest DSM Hyper Backup with Amazon Drive?! All I'm getting is a blank screen when I initiate the Hyper Backup and connect to the cloud. Anyone have an answer to this, btw? At which step do you have a blank screen? If I click on Hyper Backup, it launches backup Wizard. I then can select S3 then [Next] and a backup destination settings opened up. I don't have the keys needed to go further. Up until that point, it seems to work fine on my end. I believe he said Amazone Drive and not S3 Storage. I also encountered a blank page. I simply went back and tried again and it worked. This has nothing to do with DSM. It's either the web browser or Amazone website. Quote Link to comment Share on other sites More sharing options...
meimeiriver Posted October 19, 2016 Share #599 Posted October 19, 2016 Is anyone using the latest DSM Hyper Backup with Amazon Drive?! All I'm getting is a blank screen when I initiate the Hyper Backup and connect to the cloud. Anyone have an answer to this, btw? At which step do you have a blank screen? If I click on Hyper Backup, it launches backup Wizard. I then can select S3 then [Next] and a backup destination settings opened up. I don't have the keys needed to go further. Up until that point, it seems to work fine on my end. Thanks for your reply. I get the backup wizard. I log in, and then get to a page (synoauth.synology.com) that says: Redirect your personal information back to http://192.168.14.10:5000, please make sure http://192.168.14.10:5000 is your DS domain. After I confirm and click 'Next', it's just an empty page. Quote Link to comment Share on other sites More sharing options...
meimeiriver Posted October 19, 2016 Share #600 Posted October 19, 2016 Thanks for your reply. I get the backup wizard. I log in, and then get to a page (synoauth.synology.com) that says: Redirect your personal information back to http://192.168.14.10:5000, please make sure http://192.168.14.10:5000 is your DS domain. After I confirm and click 'Next', it's just an empty page. P.S. If Hyper Backup requires the use of Synology services (does it?) then never mind: like others, I don't mind using Xpenology, but don't feel like defrauding Synology by using fake serials, etc. Otherwise I'd still like to know. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.