Jseinfeld Posted June 21, 2020 Share #151 Posted June 21, 2020 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.1-23824 Update 6 - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: Yes, v0.13.3 for 6.2.3 by IG-88 - https://xpenology.com/forum/topic/28321-driver-extension-jun-103b104b-for-dsm623-for-918-3615xs-3617xs/ - Installation type: BAREMETAL - J4105-ITX + 8GB RAM - Notes Updated the "extra.lzma & extra2.lzma" by SSH'ing in and mounting /dev/synoboot2. Replaced the old ones with the new "extra.lzma & extra2.lzma" files and unmounted the USB from DSM. After that it was just a manual install by uploading the .PAT file. Rebooted normally and the "/dev/dri/" was working the first time. Edited June 21, 2020 by Jseinfeld Quote Link to comment Share on other sites More sharing options...
BanterBay Posted June 21, 2020 Share #152 Posted June 21, 2020 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2 24922 Update 4 - Loader version and model: Jun's v1.04b - DS918+ - Using custom extra.lzma: No - Installation type: BAREMETAL - BAREMETAL - DELL POWEREDGE T20 Xeon E3-1225V3 (32GB RAM) - Additional Comment: Everything works OK. Reboot required. Edited June 21, 2020 by BanterBay Quote Link to comment Share on other sites More sharing options...
SaugPirat Posted June 22, 2020 Share #153 Posted June 22, 2020 (edited) - Neue Installation DS3617xs auf VMware Workstation 15.5.6 (System ESXI 6.5): ERFOLGREICH - DSM-Version: DSM 6.2.3-25426 - Version und Modell des Laders: JUN'S LOADER v1.03b - DS3617xs - besteht von custom extra.lzma: NEIN - Installationsart: VMware Workstation - ASUS RAMPAGE IV BLACK EDITION | Intel i7 3930k (16 GB RAM) - Bedenken Kommentare: Keine Probleme! Alles funktioniert! Edited June 22, 2020 by SaugPirat Quote Link to comment Share on other sites More sharing options...
Moby_Dick Posted June 23, 2020 Share #154 Posted June 23, 2020 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2-23739 Update 2 - Loader version and model: Jun's v1.03b - DS3617xs - Using custom extra.lzma: No - Installation type: BAREMETAL - BAREMETAL - Supermicro X9SRi-F Xeon E5-2680v2 (128GB ECC RAM) - Additional Comment: Everything works OK. Reboot required and i had to run Synoboot.sh to disable automount of the usb-boot drive. Edited June 23, 2020 by Moby_Dick Quote Link to comment Share on other sites More sharing options...
cga20 Posted June 24, 2020 Share #155 Posted June 24, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922- update 4 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - HP Microserver Gen8 - Additional comment: reboot required | additional HP Intel network card Quote Link to comment Share on other sites More sharing options...
meduardp Posted June 26, 2020 Share #156 Posted June 26, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2-23739 Update 2 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - ASUS PRIME H270-PLUS | Intel G4620 (8 GB RAM) - Additional comments: REBOOT REQUIRED Everything works OK Quote Link to comment Share on other sites More sharing options...
Synple guy Posted June 29, 2020 Share #157 Posted June 29, 2020 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: new install - Loader version and model: JUN'S LOADER v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL HPE Proliant MicroServer Gen 10 Plus (config P16006-421) w/ Xeon E-2224, 16Gb RAM, NIC: Intel i350 AM41Gb - Additional comments: I put in the 4 disks from a bricked DS415+. After installing DSM 6.2.3-25426 , Synology ran migration from DS415+ > DS918+. It all works without issues, nice and fast. Edited June 29, 2020 by Synple guy Quote Link to comment Share on other sites More sharing options...
Paars Posted July 3, 2020 Share #158 Posted July 3, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922-update 4 - Loader version and model: Jun's Loader v1.03B - 3615XS - Using custom extra.lzma: No - Installation type: VM - ESXi 6.7.0 update 2 Build 13006603 (on HP Microserver Gen8) - Additional comment : FixSynoboot.sh & Update grub.cfg to have "DiskIdxMap=0C00" Quote Link to comment Share on other sites More sharing options...
Guest Posted July 3, 2020 Share #159 Posted July 3, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 - Loader version and model: Jun's v1.03b - DS3615xs - Using custom extra.lzma: No - Installation type: BAREMETAL - HP ProLiant Microserver Gen8 (Celeron G1610T) - Additional comment: Custom NIC: HP NC360T (built-in does NOT work); updated from web ui (it took ~6-7 min to reboot afterwards) Quote Link to comment Share on other sites More sharing options...
bullyparade Posted July 7, 2020 Share #160 Posted July 7, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 - Loader version and model: Jun's v1.03b - DS3615xs - Using custom extra.lzma: No - Installation type: BAREMETAL - HP ProLiant Microserver Gen8 (Celeron G1610T) - Additional comment: No Quote Link to comment Share on other sites More sharing options...
azhur Posted July 8, 2020 Share #161 Posted July 8, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.1.3-15152 - Loader version and model: JUN'S LOADER v1.02b - DS3615xs - Using custom extra.lzma: before upgrade - unknown (got used server with pre-installed xpenology)/after upgrade - No - Installation type: BAREMETAL - HP MicroServer Gen7 N54L, using built-in NIC - Additional comments: shutdown, replace USB stick with new one (standard Jun's Loader v1.03b), startup, upgrade|migration wizard, done. Quote Link to comment Share on other sites More sharing options...
ilovepancakes Posted July 9, 2020 Share #162 Posted July 9, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922-update 4 - Loader version and model: Jun's Loader v1.04 - 918+ - Using custom extra.lzma: No - Installation type: VM - ESXi 7.0.0 - Additional comment : Reboot required. "FixSynoboot.sh" implemented after update. Quote Link to comment Share on other sites More sharing options...
nat189 Posted July 11, 2020 Share #163 Posted July 11, 2020 (edited) Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: Jun's v1.04b - DS918+ - Using custom extra.lzma: YES - extra918plus_v0.13.3 - Installation type: BAREMETAL - ASRock J355M - Additional Comments: Reboot Required; Reboot Slow 5 min Edited July 11, 2020 by nat189 Quote Link to comment Share on other sites More sharing options...
blackmanga Posted July 12, 2020 Share #164 Posted July 12, 2020 (edited) Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922-update 5 - Loader version and model: Jun's v1.04b - DS918+ - Using custom extra.lzma: YES - extra918plus_v0.13.3 - Installation type: BAREMETAL - MB: Gigabyte H97N WiFi, CPU: Intel Xeon E3 1245 v3, onboard Intel and Atheros NIC, 10 GB Mellanox connectx-3 dual card - Additional Comments: Reboot required; Everything worked except the issue with eth2/eth3 (solution below) ~ Added Fixsynoboot.sh to be safe; ~ /dev/dri exists - i.e. HW transcoding is working; ~ changes for extra LAN ports maxlanport="4" in /etc.defaults/synoinfo.conf and /etc/synoinfo.conf; In grub.cfg set netif_num=4 ~ Although the 4 NICs are working, i had a situation where eth2 and eth3 were not able to get a proper IP address. I found out that there were some issues in creating the bridge due to VMM. I had to update ifcfg-eth2/ifcfg-eth3 files located under /etc/sysconfig/network-scripts/ and add the following 2 lines (could be unique to my situation, but hopefully it helps others) IPV6INIT=off BRIDGE=ovs_eth2 #eth3 for ifcfg-eth3 file Edited July 12, 2020 by blackmanga Highligting NICs Quote Link to comment Share on other sites More sharing options...
shadowmedicis Posted July 13, 2020 Share #165 Posted July 13, 2020 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922-6 - Loader version and model: Jun's Loader v1.04b - DS918+ - Using custom extra.lzma: No - Volume Cache SSD Active: Yes - Installation type: BREMETAL - UEFI Only - HP Proliant Microserver Gen10 X3216 + 8GB RAM - Additional comments: DSM was fully running but bootloader partition was considered as eSATA device. Applying FixSynoboot.sh fix this issue. Edited July 13, 2020 by shadowmedicis Quote Link to comment Share on other sites More sharing options...
stanky Posted July 13, 2020 Share #166 Posted July 13, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.1-23824 UPDATE 6 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - ASRock Q1900 / NIC INTEL PRO/1000 CT Desktop Adapter , PCI Express Quote Link to comment Share on other sites More sharing options...
Chili Posted July 15, 2020 Share #167 Posted July 15, 2020 (edited) Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 (latest) - Loader version and model: JUN'S LOADER v1.04b - DS819+ - Using custom extra.lzma: NO - Installation type: Migration from RS814 to - Gigabyte GA-H110M-HD3 with Celeron G3900 and 8 GB DDR3L - NIC: Intel Gigabit Ethernet - Additional comments: CPU Celeron G3900 is in DSM displayed as Celeron J3455 migration works very fine with all settings, but "Hyper BackUp" needed to deinstall/install - (BackUp Job to external USB3.0 drive remained) Edited July 15, 2020 by Chili Quote Link to comment Share on other sites More sharing options...
Ermite Posted July 16, 2020 Share #168 Posted July 16, 2020 Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: HP N54L, Intel 82576 Dual RJ45 PCIe 2.0 x1, Enermax 2.5" x1, 3.5" x1 HDD Bay, PM-MSATA22GT-R (mSATA x2, SATA Gen3 x2) PCIe SATA Expansion Card - Additional comments: 1. Update with DSM GUI to DSM 6.2.3-25426 Update 2 : All is work. Quote Link to comment Share on other sites More sharing options...
mick44 Posted July 20, 2020 Share #169 Posted July 20, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: 6.2.3-25426 - Loader version and model: JUN'S LOADER v1.0b - DS3615 - Using custom extra.lzma: NO - Installation type: BAREMETAL - DELL Optiplex 990 | i3-4130 | 8 GB RAM - Additional comments: Reboot required Quote Link to comment Share on other sites More sharing options...
andrei7radu Posted July 21, 2020 Share #170 Posted July 21, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 Update 4 - Loader version and model: Jun's Loader v1.03b for DS3615XS - Using custom extra.lzma: Yes + original zImage and rd.gz (extracted from Synology's 24922 PAT) - Installation type: BAREMETAL - ASUS H81M-K (with onboard Realtek 8111G controller) - Additional comment: Reboot required ... after that, the machine was "lost" (though booted fine, no network issue). I had to fresh remake the same USB Flash Drive, this time as "stock" (without custom extra.lzma, zImage and rd.gz). Recovered with Synology Assistant, rebooted once more and now it works like a charm (nothing modified or lost). Quote Link to comment Share on other sites More sharing options...
satdream Posted July 21, 2020 Share #171 Posted July 21, 2020 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 Update 4 - Loader version and model: JUN'S LOADER v1.03b - DS3617xs - Using custom extra.lzma: Yes - Installation type: BAREMETAL - HP Microserver Gen8 - Additional comments: 1) Manual Update 2) Once update finished, the Gen8 start to reboot automatically = switch off quickly (during the "long" boot test process of the Gen8=without issue) 3) Update extra.lzma (simple copy/paste under W10) on the SDCard from which the Gen8 boot 4) Boot Gen8 with updated SDCard => no issue with integrated NiC, the Gen8 is fine visible on network ! 5) Log via SSH then update /etc.default/synoinfo.conf if specific (eg. more HDDs etc.) the update reseted values, supposed to be restored to - esataportcfg to 0x00000 (instead default 0xff000), - usbportcfg to 0x7C000 (instead default 0x300000) = 5 USB on the Gen8 - internalportcfg to 0xFFFFFF (instead of default 0xfff) = 21 Disks support in my case Edited July 21, 2020 by satdream Quote Link to comment Share on other sites More sharing options...
OsiMood Posted July 23, 2020 Share #172 Posted July 23, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior to update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: Asrock J5005-ITX - Additional comments: Shutdown and restart do not work Quote Link to comment Share on other sites More sharing options...
krestty Posted July 25, 2020 Share #173 Posted July 25, 2020 - Outcome of the update: FAILED - DSM version prior update: DSM 6.1.7-15284 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: See addittional comments - Installation type: BAREMETAL - Nuc7i5BNB (J3144-303) | Intel i5-7260U | 16 GB RAM | Ehternet Intel I219V Gigabit - Additional comments: Tried with the extra.lzma on Jun 1.03b and with the extra3615_v0.11_test. I installed the 6.2.3 using the own Synology assistant and reboot with the USB/loader but I cannot see nothing started, even nothing in the LAN using find.synology.com. Quote Link to comment Share on other sites More sharing options...
IceBoosteR Posted July 26, 2020 Share #174 Posted July 26, 2020 (edited) - Outcome of the update: SUCCESFULL - DSM version prior update: DSM 6.2.2-24922- update 6 - Loader version and model: JUN'S LOADER v1.03b DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - Supermicro X10SLL-F, 32GB ECC RAM, Xeon E3-1270v3, 10GBit NIC Mellanox ConnectX-3, LSI SAS2008 IT-Mode - Additional comment: Reboot required, custom synoinfo, RAID degraded. I have 14 disks, all in SHR2. When rebooted after upgrade, default was back to 12 so my array was degraded! Be cautious! Had to change synoinfo and use fixsynology.sh Edited July 26, 2020 by IceBoosteR Quote Link to comment Share on other sites More sharing options...
s3urat Posted July 29, 2020 Share #175 Posted July 29, 2020 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 Update 4 - Loader version and model: Jun's Loader v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: Baremetal - HP Microserver GEN10 - Additional comments: DSM 6.2.2-24922U4 used a custom extra.lzma with Jun's Loader 1.03b (internal NICs weren't working without it) uploaded the stock extra.lzma, rd.gz and zImage from Jun's Loader 1.03b to the server via SCP SSH to the server mount /dev/synoboot2 copy the stock extra.lzma rd.gz and zImage to /dev/synoboot2, replacing the custom files unmount /dev/synoboot2 performed a manual DSM update via the Control Panel and reboot 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.