apriliars3 Posted August 24, 2022 Share #426 Posted August 24, 2022 4 minutes ago, dimakv2014 said: Did you do passthrough igpu? Did you try AI on j3455? Thanks. I have not tried as I do not have any ip camera. Quote Link to comment Share on other sites More sharing options...
dimakv2014 Posted August 24, 2022 Share #427 Posted August 24, 2022 (edited) 9 минут назад, apriliars3 сказал: I have not tried as I do not have any ip camera. You dont need ip camera to test face rec or dva, you can upload .mp4 video file with people or vehicles and simulate ip camera Edited August 24, 2022 by dimakv2014 1 Quote Link to comment Share on other sites More sharing options...
bugsbugs1 Posted August 25, 2022 Share #428 Posted August 25, 2022 good afternoon. I can't run face recognition on 1622. The built-in graphics card works. There is also a 1060 gddr5, I tried to connect it through risers, but the system does not see it. And 3221 doesn't work for me. biostar j1800nh3 Quote Link to comment Share on other sites More sharing options...
Deninyk Posted August 26, 2022 Share #429 Posted August 26, 2022 Hi, this error is because the built-in graphics are not supported. I have HD Graphics 530 and it works. Below if graphics, this error will pop up. You need a j4000+ or intel CPU with HD Graphics 530 or higher (i5 6400+) 1 Quote Link to comment Share on other sites More sharing options...
medric Posted August 26, 2022 Share #430 Posted August 26, 2022 @Peter Suh I am still working on My build. All 8 of my drives died HGST 10TB circa 2018 Not sure how but the will not power on at all. I am going to take the L shrug it off and Rebuild.. 🧯🔥 Quote Link to comment Share on other sites More sharing options...
utya Posted August 30, 2022 Share #431 Posted August 30, 2022 On 8/26/2022 at 11:14 AM, Deninyk said: Hi, this error is because the built-in graphics are not supported. I have HD Graphics 530 and it works. Below if graphics, this error will pop up. You need a j4000+ or intel CPU with HD Graphics 530 or higher (i5 6400+) so if the cpu doensn't have graphic cores, there are not ai features? Quote Link to comment Share on other sites More sharing options...
pocopico Posted August 30, 2022 Author Share #432 Posted August 30, 2022 On 8/26/2022 at 4:53 PM, medric said: @Peter Suh I am still working on My build. All 8 of my drives died HGST 10TB circa 2018 Not sure how but the will not power on at all. I am going to take the L shrug it off and Rebuild.. 🧯🔥 Thats strange and never saw 8 drives dying simultaneously. Could be the power supply. Quote Link to comment Share on other sites More sharing options...
dvuv Posted August 30, 2022 Share #433 Posted August 30, 2022 Hello, I'm little puzzled and looking for a hint from community. I have 2 Intel NUCs of different generations. Tried both automatic redpill and tinycore. 1) based on i3-7100u CPU. Installed 1622 baremetal, everything (AI tasks) works fine, no issues. Decided to install through proxmox to not waste entire NUC for a single task, specified host CPU, and PCI passthrough for GPU (HD 620). Result – AI processes constantly crash and tasks do not work. One small detail if it matters – when enabling Local Screen, or right before shut down, attached monitor goes garbage. All other time I see Syno 1622 logo. 2) I pulled HDD from this NUC and installed it as-is (proxmox setup) into 8-gen with i3-8109U CPU (HD 655 gpu). Booted without making any changes, and boom, everything works! So at this point i'm certain that I followed all steps for setting up passthrough in proxmox according to instructions and it works. I have no idea why 1622 works on baremetal, doesn't work in proxmox, but works in proxmox on a next-gen CPU. Logic says to me that it should work in the first case, but it doesn't. I'm out of clues on where to look or what else to try, any suggestions? 1 Quote Link to comment Share on other sites More sharing options...
pocopico Posted August 30, 2022 Author Share #434 Posted August 30, 2022 31 minutes ago, dvuv said: Hello, I'm little puzzled and looking for a hint from community. I have 2 Intel NUCs of different generations. Tried both automatic redpill and tinycore. 1) based on i3-7100u CPU. Installed 1622 baremetal, everything (AI tasks) works fine, no issues. Decided to install through proxmox to not waste entire NUC for a single task, specified host CPU, and PCI passthrough for GPU (HD 620). Result – AI processes constantly crash and tasks do not work. One small detail if it matters – when enabling Local Screen, or right before shut down, attached monitor goes garbage. All other time I see Syno 1622 logo. 2) I pulled HDD from this NUC and installed it as-is (proxmox setup) into 8-gen with i3-8109U CPU (HD 655 gpu). Booted without making any changes, and boom, everything works! So at this point i'm certain that I followed all steps for setting up passthrough in proxmox according to instructions and it works. I have no idea why 1622 works on baremetal, doesn't work in proxmox, but works in proxmox on a next-gen CPU. Logic says to me that it should work in the first case, but it doesn't. I'm out of clues on where to look or what else to try, any suggestions? do a bios settings check, upgrade if available, reset to default settings and try again Quote Link to comment Share on other sites More sharing options...
dvuv Posted August 30, 2022 Share #435 Posted August 30, 2022 36 минут назад, pocopico сказал: do a bios settings check, upgrade if available, reset to default settings and try again Thanks for your response. What i need to be looking at in the bios (of the host pc?) that affects proxmox setup? Bios is the latest and default (never changed) Quote Link to comment Share on other sites More sharing options...
apriliars3 Posted August 30, 2022 Share #436 Posted August 30, 2022 (edited) On 8/24/2022 at 8:39 PM, dimakv2014 said: You dont need ip camera to test face rec or dva, you can upload .mp4 video file with people or vehicles and simulate ip camera I test it with Intel G2030 on baremetal. Need to active transcoding or some codecs like AME? I can´t detect persons and vehicules. Edited August 30, 2022 by apriliars3 Quote Link to comment Share on other sites More sharing options...
dimakv2014 Posted August 30, 2022 Share #437 Posted August 30, 2022 52 минуты назад, apriliars3 сказал: I test it with Intel G2030 on baremetal. Need to active transcoding or some codecs like AME? I can´t detect persons and vehicules. You said you had a j3455, you should try it on this one. No AME needed. G2030 is Ivy bridge and doesnt support AI. Quote Link to comment Share on other sites More sharing options...
pocopico Posted August 31, 2022 Author Share #438 Posted August 31, 2022 9 hours ago, dvuv said: Thanks for your response. What i need to be looking at in the bios (of the host pc?) that affects proxmox setup? Bios is the latest and default (never changed) Clearly passthrough is not working properly. You can use the i3-7100u as a baremetal and use syno VMM to host additional VMs Quote Link to comment Share on other sites More sharing options...
apriliars3 Posted August 31, 2022 Share #439 Posted August 31, 2022 (edited) 11 hours ago, dimakv2014 said: You said you had a j3455, you should try it on this one. No AME needed. G2030 is Ivy bridge and doesnt support AI. Well, I try with J3455 on virtual, baremetal haven´t hdd free for testing. J3455 with VMWare and DVA1622 not works, or I don´t know how use SS with AI. No account, detect people or vehicles, etc. Edited August 31, 2022 by apriliars3 Quote Link to comment Share on other sites More sharing options...
marigo Posted August 31, 2022 Share #440 Posted August 31, 2022 (edited) On 8/30/2022 at 9:19 PM, dvuv said: Hello, I'm little puzzled and looking for a hint from community. I have 2 Intel NUCs of different generations. Tried both automatic redpill and tinycore. 1) based on i3-7100u CPU. Installed 1622 baremetal, everything (AI tasks) works fine, no issues. Decided to install through proxmox to not waste entire NUC for a single task, specified host CPU, and PCI passthrough for GPU (HD 620). Result – AI processes constantly crash and tasks do not work. One small detail if it matters – when enabling Local Screen, or right before shut down, attached monitor goes garbage. All other time I see Syno 1622 logo. 2) I pulled HDD from this NUC and installed it as-is (proxmox setup) into 8-gen with i3-8109U CPU (HD 655 gpu). Booted without making any changes, and boom, everything works! So at this point i'm certain that I followed all steps for setting up passthrough in proxmox according to instructions and it works. I have no idea why 1622 works on baremetal, doesn't work in proxmox, but works in proxmox on a next-gen CPU. Logic says to me that it should work in the first case, but it doesn't. I'm out of clues on where to look or what else to try, any suggestions? Great to see that you have it working in Proxmox. I had also selected the "host" CPU, but AI also not working. But now I red that I have to use PCI (GPU) passthrough. I am on a Intel i5 12th gen, so it should work as soon I have the passthrough enabled. (will do that asap) On thing I noticed that the CPU is fluctuating and I see some spikes sometimes to 15-20%. Also the used RAM is also increasing in time... Edited August 31, 2022 by marigo Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 1, 2022 Share #441 Posted September 1, 2022 Hello all and thank you for all of the effort everyone has put into this project. This is my first time setting up an XPenology system. I have a VMWare ESXi 7.0u3 system running an E3-1270 v3 Haswell I am following the steps included on the first page but I get the error Platform not found. I am guessing I am running the wrong command for my system but with all the research I have done, I am not sure what I should be doing. Any help in the right direction would be great. I am also hoping to be able to passthrough the GPU for the AI. Thank you Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 1, 2022 Share #442 Posted September 1, 2022 (edited) I believe I have been able to make some progress. I am running it with the command ./rploader.sh /build geminilake-7.1.0-42661 which is giving me a different error but is actually trying to load. After starting loader creation that is where it starts to go wrong. I have attached a screenshot of my output. Edited September 1, 2022 by jeffestewart Quote Link to comment Share on other sites More sharing options...
pocopico Posted September 1, 2022 Author Share #443 Posted September 1, 2022 2 hours ago, jeffestewart said: I believe I have been able to make some progress. I am running it with the command ./rploader.sh /build geminilake-7.1.0-42661 which is giving me a different error but is actually trying to load. After starting loader creation that is where it starts to go wrong. I have attached a screenshot of my output. Yes, you've been caught in the middle of something new. Sorry, i've fixed that, please update and run build again. 1 Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 2, 2022 Share #444 Posted September 2, 2022 Thank you. Am I running the correct command for my platform? I ran the command again and it now boots but shows as a DS920+. Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 2, 2022 Share #445 Posted September 2, 2022 Nevermind, it is working now. I had the command wrong. Thank you again for your help. Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 2, 2022 Share #446 Posted September 2, 2022 Almost made it. It boots now and it appears to be detecting the drive I have connected. I downloaded the latest version of DSM for the dva1622 42661. It is failing during the install of the .pat file. Sometimes it gets to 41% (Uploading DSM Installation Pack) or it gets to 55% (Installing DiskStation Manager) Thank you. Quote Link to comment Share on other sites More sharing options...
dimakv2014 Posted September 2, 2022 Share #447 Posted September 2, 2022 (edited) 10 минут назад, jeffestewart сказал: Almost made it. It boots now and it appears to be detecting the drive I have connected. I downloaded the latest version of DSM for the dva1622 42661. It is failing during the install of the .pat file. Sometimes it gets to 41% (Uploading DSM Installation Pack) or it gets to 55% (Installing DiskStation Manager) Thank you. Did you read forums at all?) Is it so hard?) Just download 7.1-42661 (with Update 1) about 295mb file size, while latest update is 33mb in size, which obviously not enough for full OS install. After that you can do post update to latest version if needed, and yes all information how to do it in this thread. Edited September 2, 2022 by dimakv2014 Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 2, 2022 Share #448 Posted September 2, 2022 2 hours ago, dimakv2014 said: Did you read forums at all?) Is it so hard?) Just download 7.1-42661 (with Update 1) about 295mb file size, while latest update is 33mb in size, which obviously not enough for full OS install. After that you can do post update to latest version if needed, and yes all information how to do it in this thread. Thank you for the response. I have been reading the forum. I have been downloading 7.1-42661 (with Update 1). Maybe I am downloading the incorrect file. This is the files I am downloading and it shows as 342.55MB Quote Link to comment Share on other sites More sharing options...
dimakv2014 Posted September 2, 2022 Share #449 Posted September 2, 2022 (edited) 44 минуты назад, jeffestewart сказал: Thank you for the response. I have been reading the forum. I have been downloading 7.1-42661 (with Update 1). Maybe I am downloading the incorrect file. This is the files I am downloading and it shows as 342.55MB Yes, this is correct one. P.S. If you will run into same error with this .pat file please tell all commands you are using, last time you had / symbol before Build command, maybe you have some other mistakes as well, so we can correct it. Edited September 3, 2022 by dimakv2014 Quote Link to comment Share on other sites More sharing options...
jeffestewart Posted September 3, 2022 Share #450 Posted September 3, 2022 5 hours ago, dimakv2014 said: Yes, this is correct one. P.S. If you will run into same error with this .pat file please tell all commands you are using, last time you had / symbol before Build command, maybe you have some other mistakes as well, so we can correct it. Thank you The error you saw above was a typo when writing the post. Not part of the command I entered. Also the above command wasn't working. When I ran that command it installed as a DS920+ My system is as follows Xeon E3-1270v3 ESXi 7.0u3 Virtual Machine specs CPU 4 Memory 6GB Hard Disk 1 TinyCore RedPill 0.9.0.2 vmdk (IDE interface) Hard Disk 2 8TB drive for storage Commands i ran ./rploader.sh update ./rploader.sh fullupgrade ./rploader.sh satamap ./rploader.sh serialgen DVA1622 realmac ./rploader.sh build DVA1622-7.1.0-42661 auto Pat file I am using was downloaded with the same url found in the ./rploader.sh build DVA1622-7.1.0-42661 auto process https://global.download.synology.com/download/DSM/release/7.1/42661-1/DSM_DVA1622_42661.pat Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.