chickey Posted January 30, 2022 Share #651 Posted January 30, 2022 On 1/28/2022 at 11:21 PM, cris_t said: hi. first of all thanks @pocopico for this great tool. finally i managed to create a uefi bootable flash drive. the steps are very easy but it took me about the whole day to figure out. after writing redpill tc loader image to your flash drive, you need a linux machine to add the uefi boot. in my case, i have a notebook with linux mint installed (latest edge edition). assuming that my flash drive was /dev/sdb, this is what i've done: Mount the filesystem: sudo mount -o umask=000 /dev/sdb1 /mnt Write the MBR and install the grub files required for legacy BIOS boot on the drive: (i don't know if this step is really needed but anyway it works) sudo grub-install --no-floppy --boot-directory=/mnt/boot --target=i386-pc /dev/sdb Install /EFI/BOOT/BOOTX64.EFI and other grub files required to load grub from a 64-bit UEFI firmware: sudo grub-install --removable --boot-directory=/mnt/boot --efi-directory=/mnt --target=x86_64-efi /dev/sdb Unmount the filesystem: sudo umount /dev/sdb1 after that, remove the flash drive and try it. for me, it worked at first try. no need to edit any other file. credits go to https://github.com/ndeineko/grub2-bios-uefi-usb for this helpful page without which I would never have succeeded. Worked great thank you! Quote Link to comment Share on other sites More sharing options...
adamadam Posted January 30, 2022 Share #652 Posted January 30, 2022 what pci-e card instead of Dell perc h310 to run apollolake redpill 918+? Dell perc h310 runs on ds3615xs but keeps my network crashing. a few days worked fine but the problem comes back. on ds918 + network works fine but I can not run Dell perc h310 so I would like to replace it with something else Quote Link to comment Share on other sites More sharing options...
chickey Posted January 30, 2022 Share #653 Posted January 30, 2022 (edited) Anyone had this error? cat: satamap.x: No such file or directory cat: diskmap.x: No such file or directory Edited January 30, 2022 by chickey Quote Link to comment Share on other sites More sharing options...
chickey Posted January 30, 2022 Share #654 Posted January 30, 2022 38 minutes ago, chickey said: Anyone had this error? cat: satamap.x: No such file or directory cat: diskmap.x: No such file or directory To answer my own question this is a thin client and the internal flash disk shows up as mmcblk0 which is why no drives are showing up so satamap is failing Quote Link to comment Share on other sites More sharing options...
Isaiah33 Posted January 30, 2022 Share #655 Posted January 30, 2022 (edited) Hello All, I was hoping someone could assist me with resolving my issue with drives missing from my install. The on-board sata drives show but not the 8 from my AvagoSAS controller. When running satamap it does not detect the drives either. However, I can tell tinybox does detect the SAS controller. I have tried various satamap configurations but have not had any luck. Thank you in advanced. tc@box:~$ lspci -k | grep -EiA2 'SATA|SCSI' 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) Subsystem: ASRock Incorporation Device 8c02 Kernel driver in use: ahci -- 02:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] (rev 03) Subsystem: LSI Logic / Symbios Logic Device 3020 04:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 11) Subsystem: ASRock Incorporation Device 9172 Kernel driver in use: ahci tc@box:~$ sudo lspci -k | grep -EiA2 'SATA|SCSI' 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) Subsystem: ASRock Incorporation Device 8c02 Kernel driver in use: ahci -- 02:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] (rev 03) Subsystem: LSI Logic / Symbios Logic Device 3020 04:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 11) Subsystem: ASRock Incorporation Device 9172 Kernel driver in use: ahci tc@box:~$ sudo cat /proc/scsi/sg/devices 0 0 0 0 0 1 32 0 1 1 0 0 0 0 1 32 0 1 2 0 0 0 0 1 32 0 1 3 0 0 0 0 1 32 0 1 8 0 0 0 0 1 1 0 1 tc@box:~$ sudo lspci -nnq 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v3 Processor DRAM Controller [8086:0c08] (rev 06) 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [8086:0c01] (rev 06) 00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller [8086:0c05] (rev 06) 00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI [8086:8c31] (rev 05) 00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 [8086:8c3a] (rev 04) 00:16.1 Communication controller [0780]: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #2 [8086:8c3b] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 [8086:8c2d] (rev 05) 00:1c.0 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 [8086:8c10] (rev d5) 00:1c.1 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 [8086:8c12] (rev d5) 00:1c.4 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 [8086:8c18] (rev d5) 00:1c.5 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #6 [8086:8c1a] (rev d5) 00:1c.7 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #8 [8086:8c1e] (rev d5) 00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 [8086:8c26] (rev 05) 00:1f.0 ISA bridge [0601]: Intel Corporation C224 Series Chipset Family Server Standard SKU LPC Controller [8086:8c54] (rev 05) 00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c02] (rev 05) 00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller [8086:8c22] (rev 05) 01:00.0 Ethernet controller [0200]: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] [15b3:6750] (rev b0) 02:00.0 Serial Attached SCSI controller [0107]: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:0072] (rev 03) 04:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller [1b4b:9172] (rev 11) 05:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03) 06:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03) 07:00.0 PCI bridge [0604]: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge [1a03:1150] (rev 02) 08:00.0 VGA compatible controller [0300]: ASPEED Technology, Inc. ASPEED Graphics Family [1a03:2000] (rev 21) tc@box:~$ Edited January 30, 2022 by Isaiah33 Added screenshot of error. Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 30, 2022 Share #656 Posted January 30, 2022 Proxmox SATA HDD Passthrough to DSM 7. Anyone able to achieve this? I just added a few SATA Disks manually to the DSM VM with id 100: qm set 100 -sata1 /dev/disk/by-id/<id> but they're showing on DSM Storage Manager as QEMU Harddisks missing SMART info. @haydibe @pocopico Quote Link to comment Share on other sites More sharing options...
NoFate Posted January 31, 2022 Share #657 Posted January 31, 2022 guys, if i want to change the SN by the generator, i edit the user_config.json if i then boot up, its still te old one, what do i need todo more? Quote Link to comment Share on other sites More sharing options...
chickey Posted January 31, 2022 Share #658 Posted January 31, 2022 55 minutes ago, NoFate said: guys, if i want to change the SN by the generator, i edit the user_config.json if i then boot up, its still te old one, what do i need todo more? are you building again after you make the change? Quote Link to comment Share on other sites More sharing options...
NoFate Posted January 31, 2022 Share #659 Posted January 31, 2022 6 minutes ago, chickey said: are you building again after you make the change? no, but that was indeed the trick 1 Quote Link to comment Share on other sites More sharing options...
85kedob Posted January 31, 2022 Share #660 Posted January 31, 2022 Hello. I have successfully installed redpill. Is there any way the system can lower the reserved RAM? Currently, a clean install takes 1.7GB of memory. Quote Link to comment Share on other sites More sharing options...
Smartpol Posted January 31, 2022 Share #661 Posted January 31, 2022 18 часов назад, synoxpe сказал: Proxmox SATA HDD Passthrough to DSM 7. Anyone able to achieve this? I just added a few SATA Disks manually to the DSM VM with id 100: qm set 100 -sata1 /dev/disk/by-id/<id> but they're showing on DSM Storage Manager as QEMU Harddisks missing SMART info. I does the same in my Proxmox install - Redpill is not passtrough SMART to DSM, I think I read about it in some of Tor Group posts. But in Proxmox it is not a problem, because it monitors disk health with smartctl daemon. Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #662 Posted January 31, 2022 1 hour ago, Smartpol said: Redpill is not passtrough SMART to DSM Good to know. Also I’ve allocated 4 cores DSM is showing 2 with wrong processor type (Intel i7 on host being shown as i3) Quote Link to comment Share on other sites More sharing options...
Invaliduser Posted January 31, 2022 Share #663 Posted January 31, 2022 2 minutes ago, synoxpe said: Good to know. Also I’ve allocated 4 cores DSM is showing 2 with wrong processor type (Intel i7 on host being shown as i3) Which build did you use? Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #664 Posted January 31, 2022 Just now, Invaliduser said: Which build did you use? Bromolow 7.0.1 ds3615xs Quote Link to comment Share on other sites More sharing options...
Invaliduser Posted January 31, 2022 Share #665 Posted January 31, 2022 Just now, synoxpe said: Bromolow 7.0.1 ds3615xs That uses a dual core architecture. You need broadwell-7.0.1-42218 that the DS3617 uses Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #666 Posted January 31, 2022 2 minutes ago, Invaliduser said: That uses a dual core architecture. You need broadwell-7.0.1-42218 that the DS3617 uses Oh ok! I’ll need to rebuild then. Thanks for the tip. Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #667 Posted January 31, 2022 34 minutes ago, synoxpe said: You need broadwell-7.0.1-42218 that the DS3617 uses @Invaliduser Oops build fails: [!] There doesn't seem to be a config for DS3617xs platform running 7.0.1-42218 (checked /home/tc/redpill-load/config/DS3617xs/7.0.1-42218/config.json) *** Process will exit *** Perhaps I'm missing something? Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #668 Posted January 31, 2022 31 minutes ago, synoxpe said: @Invaliduser Oops build fails: [!] There doesn't seem to be a config for DS3617xs platform running 7.0.1-42218 (checked /home/tc/redpill-load/config/DS3617xs/7.0.1-42218/config.json) *** Process will exit *** Perhaps I'm missing something? Ok had to clean the cache. Build went fine! Got stuck in the migration loop (from 3615 to 3617. Guess I need to provide fresh disks. Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #669 Posted January 31, 2022 1 hour ago, synoxpe said: Got stuck in the migration loop Did anyone succeed in installing broadwell? DSM installation gets stuck 10 min countdown timer. @Invaliduser Quote Link to comment Share on other sites More sharing options...
plarkass Posted January 31, 2022 Share #670 Posted January 31, 2022 (edited) Le 14/01/2022 à 21:36, rok1 a dit : That board has UEFI only boot capabilities. I will tell you I've been able to boot that board fine with the older TTG 7.0.1 boot images I have built. I have not tried with the tinycore stuff yet Check my reply on thi link i got a j5005 too and it works like a charm network take time to start but except that, its ok: https://github.com/pocopico/tinycore-redpill/issues/8 finally i managed to create a uefi bootable flash drive. the steps are very easy but it took me about the whole day to figure out. after writing redpill tc loader image to your flash drive, you need a linux machine to add the uefi boot. in my case, i have a notebook with linux mint installed (latest edge edition). assuming that my flash drive was /dev/sdb, this is what i've done: Mount the filesystem: sudo mount -o umask=000 /dev/sdb1 /mnt Write the MBR and install the grub files required for legacy BIOS boot on the drive: (i don't know if this step is really needed but anyway it works) sudo grub-install --no-floppy --boot-directory=/mnt/boot --target=i386-pc /dev/sdb Install /EFI/BOOT/BOOTX64.EFI and other grub files required to load grub from a 64-bit UEFI firmware: sudo grub-install --removable --boot-directory=/mnt/boot --efi-directory=/mnt --target=x86_64-efi /dev/sdb Unmount the filesystem: sudo umount /dev/sdb1 Edited January 31, 2022 by plarkass Quote Link to comment Share on other sites More sharing options...
Invaliduser Posted January 31, 2022 Share #671 Posted January 31, 2022 Yes, I was successful. But a stuck install seems to be fairly common right now. I might build another and see if anything has changed. Quote Link to comment Share on other sites More sharing options...
synoxpe Posted January 31, 2022 Share #672 Posted January 31, 2022 6 minutes ago, Invaliduser said: But a stuck install seems to be fairly common right now Ouch. That sounds concerning ☹️ Quote Link to comment Share on other sites More sharing options...
ngsupb Posted January 31, 2022 Share #673 Posted January 31, 2022 53 minutes ago, synoxpe said: Did anyone succeed in installing broadwell? DSM installation gets stuck 10 min countdown timer. @Invaliduser Had same, so I did a fresh install but turned off internet access, it does some updates during the first run to update 2 version which seems breaks the install Quote Link to comment Share on other sites More sharing options...
mttr76 Posted January 31, 2022 Share #674 Posted January 31, 2022 Hello, i am new to this forum Today, i started to install my first "NAS", but i ran into some problems. Because i am very new to the topic, i decided to follow a YouTube Tutorial. But when i tried to search my usb stick and select it, this weird errow message comes up: So my loader is definitely on the SanDisk and i also tried a different USB Stick as well. And of course, i tried a USB 2.0 port, but always the same error code. And the second option "Realtek" should by my second network card, since my pc got two. And i don´t know what to do, since the system obviously saw the usb stick, but could not select it. If i skip this part of the tutorial, the "Synology" boots in the screen where you have to put your .pat file in, but stops the installation at about 60%. Could anybody please help me? Thank you This would be the tutorial i followed. I tried to install the DSM on Bare Metal and not on a VM, but i think that both are very similiar, and that was the best tutorial i could find. 1 1 Quote Link to comment Share on other sites More sharing options...
plarkass Posted January 31, 2022 Share #675 Posted January 31, 2022 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.