shibby Posted March 18 Share #1151 Posted March 18 On 3/17/2024 at 7:03 AM, Peter Suh said: Perhaps you want to take the loader.img file that was created in the middle. Yep, this is exacly what i need At the moment i`m running DSM 6.2.3 for DS3615xs using Jun`s loader 1.3b. I am able to boot loader from USB drive by pressing "backup" button for 30 seconds on boot. This is a temporary solution. After all i want to flash loader permamently to ReadyNAS flash by "dd" command. I tried to boot your TCRP from USB drive and it works. I`ll try to compile redpill using M-Shell tools BUT after all i will not able to flash loader to internal flash memory 😕 Each time when i will restart ReadyNAS i will have to push "backup" button to start NAS from USB drive. Quote Link to comment Share on other sites More sharing options...
shibby Posted March 18 Share #1152 Posted March 18 Nevermind All works fine Works even with Exos 14TB 1 Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted March 23 Author Share #1153 Posted March 23 [NOTICE] TCRP-mshell NMVe / MMC type media bootloader available function distribution This function has already been implemented in rr a long time ago. It was reflected a little late in mshell. It was difficult to obtain mmc and I didn't know how to create emmc by emulating it, so I put it on hold and then added the NMVe / MMC bootloader function. NVMe has been sufficiently tested and verified. MMC has asked Korean users to test it. Like the picture below This is an example of NVMe, but the information for the nvme0n1 device will be displayed instead, as shown below. Below that, in Friend, Loader BUS: nvme If you see , it is normal. 1 Quote Link to comment Share on other sites More sharing options...
djvas335 Posted April 1 Share #1154 Posted April 1 Hi, Peter, how can we pass parameters for kernel modules, I tried using modprobe.d however this did not work, I need to set some parameters for mlx4_core driver to be applied at boottime Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted April 2 Author Share #1155 Posted April 2 15 hours ago, djvas335 said: Hi, Peter, how can we pass parameters for kernel modules, I tried using modprobe.d however this did not work, I need to set some parameters for mlx4_core driver to be applied at boottime Quote Link to comment Share on other sites More sharing options...
djvas335 Posted April 2 Share #1156 Posted April 2 Thanks for replying, I checked the link however I did not find the relevant information, can you please point the relevant section ? What I need is to add some options to the mlx4_core driver like this, I am not sure how to do this, is this to be done at loader creation ? Or this can be done directly from DSM ? options mlx4_core roce_mode=2 5 hours ago, Peter Suh said: Quote Link to comment Share on other sites More sharing options...
Captainfingerbang Posted April 5 Share #1157 Posted April 5 (edited) On 3/23/2024 at 10:50 AM, Peter Suh said: [NOTICE] TCRP-mshell NMVe / MMC type media bootloader available function distribution This function has already been implemented in rr a long time ago. It was reflected a little late in mshell. It was difficult to obtain mmc and I didn't know how to create emmc by emulating it, so I put it on hold and then added the NMVe / MMC bootloader function. NVMe has been sufficiently tested and verified. MMC has asked Korean users to test it. Like the picture below This is an example of NVMe, but the information for the nvme0n1 device will be displayed instead, as shown below. Below that, in Friend, Loader BUS: nvme If you see , it is normal. Hi peter, sorry off topic but i know you dont like pm's I have a friend who needs a solution for a loader that will allow 40 or so drives plus LSI 9x00 HBA card. Do you have something like HD6500 with ability for HBA? Or at least know of something like this? possibly in RR? OR ANY loader in fact, that will allow 40 drives + HBA card? Edited April 5 by Captainfingerbang Quote Link to comment Share on other sites More sharing options...
ULSY Posted April 6 Share #1158 Posted April 6 Hey @Peter Suh I have Kernel issues, Network is no longer reachable. How can I solve this issue ? Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted April 7 Author Share #1159 Posted April 7 14 hours ago, ULSY said: Hey @Peter Suh I have Kernel issues, Network is no longer reachable. How can I solve this issue ? Wait a minute, but I don't think you should do this. There is one more thing that needs to be modified. Sorry Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted April 7 Author Share #1160 Posted April 7 vi my :295 #curl -skL# https://raw.githubusercontent.com/PeterSuh-Q3/redpill-load/master/bundled-exts.json -o /home/tc/redpill-load/bundled-exts.json :wq! Edit the *load/b*.json file once again You need to take one more action as shown below. Otherwise, the changes made above will disappear and be restored. Quote Link to comment Share on other sites More sharing options...
midiman007 Posted April 24 Share #1161 Posted April 24 On 5/2/2023 at 11:16 AM, Peter Suh said: [NOTICE] Official distribution of DSM 7.2-64551 RC version to M SHELL for TCRP has been completed. During the DSM 7.2 RC installation process, the automatic installation of the latest version of DSM still has problems, so a file corruption message appears. If you download and install DSM manually, there is no problem. Thanks @wjz304 I just installed bare metal THis was a bare metal box with spare parts I had from my old pc Thanks so much for this I just built a DS1823xs+ with 7.2.1 DSM update 5 on a MSI Z97-GD65 Gaming LGA 1150 Intel Z97 HDMI SATA 6Gb/s USB 3.0 ATX Intel Motherboard and Intel Core i7-4790K with 32 gigs of ram with version v0.9.5.0. Now for set it was 1,2,3. The only issue I can see is if I try and set the power schedule it is giving me a network error. Say please check you network setting. Now the case has 6 bays for HD, the mother board has 8 HD dId I over do my install by installing a DS1823xs+? Right now I have 5 HD installed. Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted April 26 Author Share #1162 Posted April 26 On 4/25/2024 at 4:42 AM, midiman007 said: I just installed bare metal THis was a bare metal box with spare parts I had from my old pc Thanks so much for this I just built a DS1823xs+ with 7.2.1 DSM update 5 on a MSI Z97-GD65 Gaming LGA 1150 Intel Z97 HDMI SATA 6Gb/s USB 3.0 ATX Intel Motherboard and Intel Core i7-4790K with 32 gigs of ram with version v0.9.5.0. Now for set it was 1,2,3. The only issue I can see is if I try and set the power schedule it is giving me a network error. Say please check you network setting. Now the case has 6 bays for HD, the mother board has 8 HD dId I over do my install by installing a DS1823xs+? Right now I have 5 HD installed. The above error message appears not only here but also in other places. However, it does not affect the actual operation of the scheduler. The last changed settings will remain the same. Please try out StartUp and Shutdown in action. However, I'm not sure if it's a Synology bug or a REDPILL bug, but there is a problem with the schedule operating because weekdays and weekends are differentiated. Maybe your weekend doesn't work out the way you want it to. I experienced this phenomenon a long time ago and was not using the weekend setting. Didn't this problem occur with the genuine product? Quote Link to comment Share on other sites More sharing options...
midiman007 Posted April 26 Share #1163 Posted April 26 16 minutes ago, Peter Suh said: The above error message appears not only here but also in other places. However, it does not affect the actual operation of the scheduler. The last changed settings will remain the same. Please try out StartUp and Shutdown in action. However, I'm not sure if it's a Synology bug or a REDPILL bug, but there is a problem with the schedule operating because weekdays and weekends are differentiated. Maybe your weekend doesn't work out the way you want it to. I experienced this phenomenon a long time ago and was not using the weekend setting. Didn't this problem occur with the genuine product? Peter thanks for your reply. Again thank you for your hard work on the loader. After a complete rebuild the PC will shut down and not power on. Really strange. Yes I did notice that even though the error appeared the boxes were checked and the PC shutdown at night but will not power on in the morning. I will try removing the weekend task and just use the weekday and see if that is the issue. I don't know about a true Sysology NAS since all of my OEM NAS's are QNaps. Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted April 27 Author Share #1164 Posted April 27 13 hours ago, midiman007 said: Peter thanks for your reply. Again thank you for your hard work on the loader. After a complete rebuild the PC will shut down and not power on. Really strange. Yes I did notice that even though the error appeared the boxes were checked and the PC shutdown at night but will not power on in the morning. I will try removing the weekend task and just use the weekday and see if that is the issue. I don't know about a true Sysology NAS since all of my OEM NAS's are QNaps. There was one thing I didn't mention. The point is that not all MOBOs work with this power reservation setting. (I understand that S5 in the CMOS BIOS is involved.) In particular, there are reports from users that MSI's products are incompatible with REDPILL. (The NIC does not respond for no particular reason, etc.) Quote Link to comment Share on other sites More sharing options...
midiman007 Posted April 27 Share #1165 Posted April 27 12 hours ago, Peter Suh said: There was one thing I didn't mention. The point is that not all MOBOs work with this power reservation setting. (I understand that S5 in the CMOS BIOS is involved.) In particular, there are reports from users that MSI's products are incompatible with REDPILL. (The NIC does not respond for no particular reason, etc.) Thanks for the reply. This is why I was asking before I started pulling my hair out and spending hours trying to resolve it but only to find out that the MSI board my no support it. The only thing I found strange is that I had a ds2422+ with @fbelavenuto REDPILL it powered off but not on then I used your REDPlILL to update to a ds1823xs+ and it worked for a few days. Then I was getting that network error so I used your REDPILL wiped the drives and rebuilt it to a clean ds1823xs+ now it only shuts down. Strange yes I know. I am not saying it's anything you are anyone did just that it is intermittent. Quote Link to comment Share on other sites More sharing options...
lev22885 Posted April 29 Share #1166 Posted April 29 (edited) Good afternoon, I’m thinking of returning to your bootloader again, but I have two main questions: 1) Has m2 started working correctly on many boards compared to mid-2023? (I have Huananzhi QD4) 2) And is there a driver for NCT6793D (nct6793)? Or do you have to assemble it yourself and integrate it into your bootloader? (I ask because I want a working fan control function) I apologize if these questions have already been discussed in the Xpenology forum threads regarding your loader Edited April 29 by lev22885 Quote Link to comment Share on other sites More sharing options...
gericb Posted April 29 Share #1167 Posted April 29 (edited) On 4/26/2024 at 11:53 PM, Peter Suh said: There was one thing I didn't mention. The point is that not all MOBOs work with this power reservation setting. (I understand that S5 in the CMOS BIOS is involved.) In particular, there are reports from users that MSI's products are incompatible with REDPILL. (The NIC does not respond for no particular reason, etc.) Indeed! Thanks @Peter Suh for the mental ping, regarding the Power Schedule & S5. I had not been able to get that working reliably, and this mention was all it took! I have an XPS 8950 12th Gen i7, running the SA6400 with your latest bootloader/Friend. There is a "Deep Sleep Control" in the BIOS. I had it disabled, so I could enable "WOL". Could not get Shutdown/Startup working correctly, but as soon as I enabled "Deep Sleep Control" Enabled in S4 and S5, it automatically disabled the BIOS WOL feature, but the Power Schedule works perfectly, even with multiple Startup/Shutdown configured for a 24HR period. So you are right, it does seem to rely on S4/S5. I don't generally think I'd care to much for WOL, at least right now, possibly later I might. If in the BIOS settings the 2 options seem to be mutually exclusive with the built-in Intel NIC, I'll cross that bridge if/when I need to. Update: https://www.dell.com/support/kbdoc/en-us/000146067/newer-dell-system-models-will-not-wake-on-lan-with-deep-sleep-control-set-to-s5-in-the-windows Edited April 29 by gericb 1 Quote Link to comment Share on other sites More sharing options...
midiman007 Posted May 1 Share #1168 Posted May 1 On 4/29/2024 at 4:26 PM, gericb said: Indeed! Thanks @Peter Suh for the mental ping, regarding the Power Schedule & S5. I had not been able to get that working reliably, and this mention was all it took! I have an XPS 8950 12th Gen i7, running the SA6400 with your latest bootloader/Friend. There is a "Deep Sleep Control" in the BIOS. I had it disabled, so I could enable "WOL". Could not get Shutdown/Startup working correctly, but as soon as I enabled "Deep Sleep Control" Enabled in S4 and S5, it automatically disabled the BIOS WOL feature, but the Power Schedule works perfectly, even with multiple Startup/Shutdown configured for a 24HR period. So you are right, it does seem to rely on S4/S5. I don't generally think I'd care to much for WOL, at least right now, possibly later I might. If in the BIOS settings the 2 options seem to be mutually exclusive with the built-in Intel NIC, I'll cross that bridge if/when I need to. Update: https://www.dell.com/support/kbdoc/en-us/000146067/newer-dell-system-models-will-not-wake-on-lan-with-deep-sleep-control-set-to-s5-in-the-windows Thanks for the info, Yes @Peter Suh bootloader/Friend has made installing a dream and as easy as 1,2,3. I tried ARC but I could not find a clear document / video on how install DSM with it. Quote Link to comment Share on other sites More sharing options...
9xoqreyua Posted May 5 Share #1169 Posted May 5 Hi, I did follow the tutorial and used both RedPill & ARL &m-shell options. I tried multiple times installing DS918+/DS920+/DS3622xs+ and everytime installig DSM via IP::5000/web_index.html succeded, eg. However. after rebooting - I could not boot the machine. Are there any additional steps I need to do or is there a way to check/correct the DSM bootloader from disk? Regards Quote Link to comment Share on other sites More sharing options...
9xoqreyua Posted May 5 Share #1170 Posted May 5 additiona info - I have booted from debian live cd and checked using efibootmgr - I dont see any DSM-related boot entry with this its unable to load althouth the DSM installation finished succesfully. Question - how to correct the boot now? Quote Link to comment Share on other sites More sharing options...
midiman007 Posted May 5 Share #1171 Posted May 5 5 hours ago, 9xoqreyua said: Hi, I did follow the tutorial and used both RedPill & ARL &m-shell options. I tried multiple times installing DS918+/DS920+/DS3622xs+ and everytime installig DSM via IP::5000/web_index.html succeded, eg. However. after rebooting - I could not boot the machine. Are there any additional steps I need to do or is there a way to check/correct the DSM bootloader from disk? Regards Try @Peter Suh Redpill. He has a great document online at git hub. His worked really great for me. It was as easy was 1,2,3. Quote Link to comment Share on other sites More sharing options...
9xoqreyua Posted May 5 Share #1172 Posted May 5 I was able to boot is using arpl-i18n-23.10.4.img DMS is up&running. Is there a similar way to run QNAP QTS? Quote Link to comment Share on other sites More sharing options...
midiman007 Posted May 5 Share #1173 Posted May 5 15 minutes ago, 9xoqreyua said: I was able to boot is using arpl-i18n-23.10.4.img DMS is up&running. Is there a similar way to run QNAP QTS? I don't think so since QNap has not release there code under the GPL lic. Which is not good for the lic part. On another note. I have 3 QNap Nas's they will not show up under Linux desktop network browser. This DSM will. I filled a ticket and the India programmers are stumped as to why. So much for buying a Nas and getting support. Yes I know you can \\ip address and get there, but with all the stuff going on with MS these days more people might switch to Linux and there produces should work like 1,2,3. Quote Link to comment Share on other sites More sharing options...
9xoqreyua Posted May 5 Share #1174 Posted May 5 thanks, I just sold y QNAP and moved to TerraMaster where the software is limited compared to QTS. So, just jumped on DSM, yet still missing QTS if there's a change in getting QTS on my TerraMaster that would be just great Quote Link to comment Share on other sites More sharing options...
midiman007 Posted May 5 Share #1175 Posted May 5 (edited) 3 hours ago, 9xoqreyua said: thanks, I just sold y QNAP and moved to TerraMaster where the software is limited compared to QTS. So, just jumped on DSM, yet still missing QTS if there's a change in getting QTS on my TerraMaster that would be just great I have a Tera Master also yes it's horrible. You can install DSM from what I have read on a tera master. That maybe a great solution. DSM is different in some ways to a QNap not worse not better. QNAps are more unfriendly to new NAs users unlike DSM. What I hate about all store bought Nas's they are under powered and starved for ram for most stuff unlike a PC. Edited May 5 by midiman007 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.