IG-88 Posted April 26, 2020 Author Share #76 Posted April 26, 2020 14 minutes ago, T-REX-XP said: Just one more question: does the new extra lzma contains driver for Intel® I210AT? yes, i used the same new intel source code as for the 6.2.2 drivers, it should be igb.ko Quote Link to comment Share on other sites More sharing options...
T-REX-XP Posted April 26, 2020 Share #77 Posted April 26, 2020 1 hour ago, IG-88 said: yes, i used the same new intel source code as for the 6.2.2 drivers, it should be igb.ko What is clear install ?? i try to install dsm without saving setting, then i have empty system with my data. but still no /dev/dri folder(( Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 26, 2020 Author Share #78 Posted April 26, 2020 3 hours ago, T-REX-XP said: What is clear install ?? its usually on a single empty disk to make sure everything is ok and its possible to try things without doing anything to the system in use its also possible to use the normal system and reset it by installing with the 2nd option in grub, that keeps the data/raid but does a factory install of dsm it should overwrite the system partition and it should be the same as a clean/fresh install 3 hours ago, T-REX-XP said: i try to install dsm without saving setting, then i have empty system with my data. but still no /dev/dri folder(( not sure, is that a question or did you already use the 2nd option in grub to reinstall dsm? Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 27, 2020 Author Share #79 Posted April 27, 2020 (edited) 9 hours ago, T-REX-XP said: I have successfully updated to the 6.2.3 with zImage and rd files and with 0.10 extra file, and all works fine except hw transcoding, the folder /dev/dri/ is missing (( HW: asus p10s-i/Intel® C232 Chipset CPU: G4620 what did you have before you updated to 918+ 6.2.3 and did /dev/dri worked before the update? i did not see any indications in your log that 915 was loaded before the 6.2.3 update and the only messages that i saw where when you updated to 6.2.3 and still used juns i915 driver, what resultet in messages about missing symbols when the i915 driver loaded its a xeon chipset and theb oard does not have video out like hdmi/dvi as usual or intel desktop chipset/cpu, maybe the board is not ale to use the gpu of a desktop cpu? Edited April 27, 2020 by IG-88 Quote Link to comment Share on other sites More sharing options...
TunTun Posted April 27, 2020 Share #80 Posted April 27, 2020 18 hours ago, kosty79 said: i tried: Clean install 6.2.3UNSUCCESSFUL CPU: J5005 MB: asrock j5005 RAM: 1x4GB DDR4 2400 NIC:Realtek 8111 USB image (EFI) + jun loader 1.04b ds918+ + IG-88 extra.lzma/extra2.lzma for loader 1.04b ds918+ DSM 6.2.3 v0.10 Hardware (hw) transcoding not WORK SN and MAC is valid - i can use quickConnect /dev/dri has - card0 renderD128 activation.conf - not present Almost the same question as me Quote Link to comment Share on other sites More sharing options...
T-REX-XP Posted April 27, 2020 Share #81 Posted April 27, 2020 (edited) 7 hours ago, IG-88 said: not sure, is that a question or did you already use the 2nd option in grub to reinstall dsm? No, just choose the option during the installation process. There are to options: save my configuration and reinstall OS or clear system settings and install OS from scratch (with data saving). I have chosen the second one. One more thing Also, I have tried to install os to the empty drive(as you write below), all initial configuration are presented: vid&pid, mac, serial, But i have got an error 13 during the install process. and I can't finish the installation process successfully (( Edited April 27, 2020 by T-REX-XP Quote Link to comment Share on other sites More sharing options...
Eduardo Posted April 27, 2020 Share #82 Posted April 27, 2020 On 4/21/2020 at 11:38 PM, IG-88 said: bare metal install? i dont have this on my system with a 9211-8i (IT), there are smart values, i can can run the smart quick test and get a healty the driver used atm is from kernel 4.4.59 i will try to compile a more recent and see it it works, if not i still can put back jun's driver from initial 1,04b loader, should also work Hi IG-88, All working fine but little smart info issue. Which files could we try to put back from Jun? Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 27, 2020 Author Share #83 Posted April 27, 2020 57 minutes ago, Eduardo said: All working fine but little smart info issue. Which files could we try to put back from Jun? mpt3sas.ko Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 27, 2020 Author Share #84 Posted April 27, 2020 13 hours ago, T-REX-XP said: have chosen the second one. thats the same as a clean install to one disk, so the problem must be something else did you read my question about the hardware transcoding working with former versions of dsm? https://xpenology.com/forum/topic/28321-driver-extension-jun-104b-for-dsm623-for-918/?do=findComment&comment=142841 Quote Link to comment Share on other sites More sharing options...
dolbycat Posted April 27, 2020 Share #85 Posted April 27, 2020 On 4/26/2020 at 5:27 PM, kosty79 said: i tried: Clean install 6.2.3UNSUCCESSFUL CPU: J5005 MB: asrock j5005 RAM: 1x4GB DDR4 2400 NIC:Realtek 8111 USB image (EFI) + jun loader 1.04b ds918+ + IG-88 extra.lzma/extra2.lzma for loader 1.04b ds918+ DSM 6.2.3 v0.10 Hardware (hw) transcoding not WORK SN and MAC is valid - i can use quickConnect /dev/dri has - card0 renderD128 activation.conf - not present turn off "VD-T" option in Bios Quote Link to comment Share on other sites More sharing options...
T-REX-XP Posted April 27, 2020 Share #86 Posted April 27, 2020 20 hours ago, IG-88 said: what did you have before you updated to 918+ 6.2.3 and did /dev/dri worked before the update? I'm Sorry for delay. No, the folder /dev/dri didn't presented before update and the transcoding didn't worked. 20 hours ago, IG-88 said: hdmi/dvi as usual or intel desktop chipset/cpu, maybe the board is not ale to use the gpu of a desktop cpu? Yep. It's make sense. I have found the same issue with this chipset on several forums related to the plex. All other things is working fine after update. Quote Link to comment Share on other sites More sharing options...
dolbycat Posted April 28, 2020 Share #87 Posted April 28, 2020 I5-8500t , asus h370i gaming -> dev/dri/ exists but DS video H/W transcoding failed -> Jellyfin H/W transcoding SUCCESSFUL Quote Link to comment Share on other sites More sharing options...
Eduardo Posted April 28, 2020 Share #88 Posted April 28, 2020 19 hours ago, IG-88 said: mpt3sas.ko I modded your extra2.lzma with Juns' original mpt3sas.ko but DSM doesn´t like and doesn't boot 😂. On my XPE I can't play now with a chroot jail and I tried on a Ubuntu machine. Cpio compression should be different, I guess. Quote Link to comment Share on other sites More sharing options...
staratlas Posted April 28, 2020 Share #89 Posted April 28, 2020 (edited) @Eduardo, @IG-88 I have a same issue about SMART info. my xpenology is running on esxi 6.7, use jun's loader 1.04b and IG-88's extension 0.10. I paththrough LSI(Avago) HBA SAS3008 (9300-8I) and attached vm. I connected 4 SSDs to HBA and Storage Manager show 4 SSD devices (drive 2,4,5,6 and drive 3 is vmware virtual disk). But in my Storage Manager, device icon is not HDD, like a USB device ? (Please see my attached image) and not show up SMART info. After that i tried to replace "mpt3sas.ko" to juns original one in /usr/lib/modules/ folder, nothing changed. Edited April 28, 2020 by staratlas Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 28, 2020 Author Share #90 Posted April 28, 2020 1 hour ago, Eduardo said: I modded your extra2.lzma with Juns' original mpt3sas.ko but DSM doesn´t like and doesn't boot 😂. On my XPE I can't play now with a chroot jail and I tried on a Ubuntu machine. Cpio compression should be different, I guess. tried this yet too and found out why i had smart status - i accidentally used the similar looking 8 port ahci controller that uses even the same cable as my mpt2 sas controller after changing and trying i could reproduce your error with the mpt3sas from jun's extra (does not load) i made a new mpt3sas from the latest source i had around and the driver at least works with my old sas9211-8i mpt3sas version 27.00.01.00 loaded mpt3sas 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control mpt3sas 0000:01:00.0: enabling device (0000 -> 0002) mpt2sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (16339516 kB) mpt2sas_cm0: IOC Number : 0 mpt2sas_cm0: CurrentHostPageSize is 0: Setting default host page size to 4k mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 126 ... mpt2sas_cm0: port enable: SUCCESS still no smart but it would be a improvement for some people with newer sas controllers with SAS33xx, SAS37xx cips here are the device id's that would be supported (vendor 1000) 0064 SAS2116 PCI-Express Fusion-MPT SAS-2 [Meteor] 0065 SAS2116 PCI-Express Fusion-MPT SAS-2 [Meteor] 006e SAS2308 PCI-Express Fusion-MPT SAS-2 0070 SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] 0072 SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] 0074 SAS2108 PCI-Express Fusion-MPT SAS-2 [Liberator] 0076 SAS2108 PCI-Express Fusion-MPT SAS-2 [Liberator] 0077 SAS2108 PCI-Express Fusion-MPT SAS-2 [Liberator] 007e SSS6200 PCI-Express Flash SSD 0080 SAS2208 PCI-Express Fusion-MPT SAS-2 0081 SAS2208 PCI-Express Fusion-MPT SAS-2 0082 SAS2208 PCI-Express Fusion-MPT SAS-2 0083 SAS2208 PCI-Express Fusion-MPT SAS-2 0084 SAS2208 PCI-Express Fusion-MPT SAS-2 0085 SAS2208 PCI-Express Fusion-MPT SAS-2 0086 SAS2308 PCI-Express Fusion-MPT SAS-2 0087 SAS2308 PCI-Express Fusion-MPT SAS-2 0090 SAS3108 PCI-Express Fusion-MPT SAS-3 0091 SAS3108 PCI-Express Fusion-MPT SAS-3 0094 SAS3108 PCI-Express Fusion-MPT SAS-3 0095 SAS3108 PCI-Express Fusion-MPT SAS-3 0096 SAS3004 PCI-Express Fusion-MPT SAS-3 0097 SAS3008 PCI-Express Fusion-MPT SAS-3 00aa 00ab SAS3516 Fusion-MPT Tri-Mode RAID On Chip (ROC) 00ac SAS3416 Fusion-MPT Tri-Mode I/O Controller Chip (IOC) 00ad 00ae SAS3508 Fusion-MPT Tri-Mode RAID On Chip (ROC) 00af SAS3408 Fusion-MPT Tri-Mode I/O Controller Chip (IOC) 00c0 SAS3324 PCI-Express Fusion-MPT SAS-3 00c1 SAS3324 PCI-Express Fusion-MPT SAS-3 00c2 SAS3324 PCI-Express Fusion-MPT SAS-3 00c3 SAS3324 PCI-Express Fusion-MPT SAS-3 00c4 SAS3224 PCI-Express Fusion-MPT SAS-3 00c5 SAS3316 PCI-Express Fusion-MPT SAS-3 00c6 SAS3316 PCI-Express Fusion-MPT SAS-3 00c7 SAS3316 PCI-Express Fusion-MPT SAS-3 00c8 SAS3316 PCI-Express Fusion-MPT SAS-3 00c9 SAS3216 PCI-Express Fusion-MPT SAS-3 00d0 SAS3716 Fusion-MPT Tri-Mode RAID Controller Chip (ROC) 00d1 SAS3616 Fusion-MPT Tri-Mode I/O Controller Chip (IOC) 00d2 02b0 Virtual Endpoint on PCIe Switch 1 Quote Link to comment Share on other sites More sharing options...
ewgennt Posted April 28, 2020 Share #91 Posted April 28, 2020 (edited) Hi, everybody. Please do not kick hard, I'm new here (I apologize in advance for the stupid question). I have a motherboard (ASUS j1800i-c) with 2 SATA ports and a controller (PCI-E to 4 SATA) with 4 SATA ports is inserted into it. When I connect 6 disks to all ports, the system only sees 4 disks. Do I understand correctly that I have an incorrectly set (Sata Port Map=6)? I heard that (Sata Port Map=24) can help the system see 6 disks? The system is installed jun 1.04 b for DSM6.2.3 for 918+. Edited April 28, 2020 by ewgennt Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 28, 2020 Author Share #92 Posted April 28, 2020 1 hour ago, ewgennt said: . I have a motherboard (ASUS j1800i-c) with 2 SATA ports and a controller (PCI-E to 4 SATA) with 4 SATA ports is inserted into it. When I connect 6 disks to all ports, the system only sees 4 disks. maybe you have a controller using multiplexing and that is not supported in dsm whats the added controller? might be a 2port sata chip plus multiplexer chip Quote Link to comment Share on other sites More sharing options...
IG-88 Posted April 29, 2020 Author Share #93 Posted April 29, 2020 7 hours ago, Eduardo said: I modded your extra2.lzma with Juns' original mpt3sas.ko but DSM doesn´t like and doesn't boot 😂. On my XPE I can't play now with a chroot jail and I tried on a Ubuntu machine. Cpio compression should be different, I guess. as a newer mpt3sas.ko made no difference and jun's mpt3sys did not work i assumed the difference might be on level lower so i kept the new mpt3sas v27.0.0.1 and replaced my own new complied version (synology kernel source 24992) of scsi_transport_spi.ko, scsi_transport_sas.ko, raid_class.ko with the files from jun's original extra/extra2 test looks good, no problems loading mpt3sas and there are smart infos now 1 Quote Link to comment Share on other sites More sharing options...
staratlas Posted April 29, 2020 Share #94 Posted April 29, 2020 (edited) 8 hours ago, IG-88 said: i made a new mpt3sas from the latest source i had around and the driver at least works with my old sas9211-8i mpt3sas version 27.00.01.00 loaded mpt3sas 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control mpt3sas 0000:01:00.0: enabling device (0000 -> 0002) mpt2sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (16339516 kB) mpt2sas_cm0: IOC Number : 0 mpt2sas_cm0: CurrentHostPageSize is 0: Setting default host page size to 4k mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 126 ... mpt2sas_cm0: port enable: SUCCESS Can i get latest mpt3sas.ko ? I think driver version of mpt3sas in extension 0.10 is "09.102.00.00". Is this correct ? here is my dmesg with extension 0.10 [ 1.904610] mpt3sas version 09.102.00.00 loaded [ 1.907235] mpt3sas 0000:1b:00.0: enabling device (0000 -> 0002) [ 1.907310] mpt3sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (8168964 kB) [ 1.966042] mpt3sas_cm0: MSI-X vectors supported: 96, no of cores: 2, max_msix_vectors: -1 [ 1.966315] mpt3sas0-msix0: PCI-MSI-X enabled: IRQ 58 [ 1.966316] mpt3sas0-msix1: PCI-MSI-X enabled: IRQ 59 [ 1.966318] mpt3sas_cm0: iomem(0x00000000fd140000), mapped(0xffffc90000240000), size(65536) [ 1.966319] mpt3sas_cm0: ioport(0x0000000000002000), size(256) [ 2.087367] mpt3sas_cm0: Allocated physical memory: size(16224 kB) [ 2.087368] mpt3sas_cm0: Current Controller Queue Depth(9643),Max Controller Queue Depth(9856) [ 2.087369] mpt3sas_cm0: Scatter Gather Elements per IO(128) [ 2.132823] mpt3sas_cm0: LSISAS3008: FWVersion(16.00.10.00), ChipRevision(0x02), BiosVersion(08.37.00.00) [ 2.132825] mpt3sas_cm0: Protocol=( [ 2.134220] mpt3sas_cm0: sending port enable !! [ 2.135667] mpt3sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b009156198), phys(8) [ 2.144346] mpt3sas_cm0: port enable: SUCCESS Edited April 29, 2020 by staratlas Quote Link to comment Share on other sites More sharing options...
sarieri Posted April 29, 2020 Share #95 Posted April 29, 2020 3 hours ago, IG-88 said: as a newer mpt3sas.ko made no difference and jun's mpt3sys did not work i assumed the difference might be on level lower so i kept the new mpt3sas v27.0.0.1 and replaced my own new complied version (synology kernel source 24992) of scsi_transport_spi.ko, scsi_transport_sas.ko, raid_class.ko with the files from jun's original extra/extra2 test looks good, no problems loading mpt3sas and there are smart infos now Hi, Should this method help resolving the no SMART info issue of mpt3sas in extra.lzma v0.1 for dsm6.23? Quote Link to comment Share on other sites More sharing options...
ewgennt Posted April 29, 2020 Share #96 Posted April 29, 2020 8 часов назад, IG-88 сказал: maybe you have a controller using multiplexing and that is not supported in dsm whats the added controller? might be a 2port sata chip plus multiplexer chip A regular non-multiplex controller (Espada PCIe4SATA3ASM) is inserted into the PCI-E 2.0 slot of the motherboard. But the system sees only 4 disks, 2 connected to the motherboard and 2 connected to the controller. If you connect one disk to the controller in turn in each slot, then it is visible in the system. Quote Link to comment Share on other sites More sharing options...
Eduardo Posted April 29, 2020 Share #97 Posted April 29, 2020 9 hours ago, IG-88 said: as a newer mpt3sas.ko made no difference and jun's mpt3sys did not work i assumed the difference might be on level lower so i kept the new mpt3sas v27.0.0.1 and replaced my own new complied version (synology kernel source 24992) of scsi_transport_spi.ko, scsi_transport_sas.ko, raid_class.ko with the files from jun's original extra/extra2 test looks good, no problems loading mpt3sas and there are smart infos now Nice! This new way can be useful for other hardware too. Quote Link to comment Share on other sites More sharing options...
deadsquirrel Posted April 29, 2020 Share #98 Posted April 29, 2020 IG88, Is there a chance to have cpu-frequency scaling governor module cpufreq_ondemand.ko to allows rapid, dynamic cpu frequency change in response to demand, but reducing power when there is no demand? I have a Pentium Anniversary edition that scales from 800-4400MHz, but it is locked at either end of frequency scale by either the performance or power saving governor. I understand there is a script to make some rudimentary changes to frequency but It would be ideal if this governor was available. I'm not sure I have the necessary wherewithall to compile on myself but am happy to give that a try with some pointing at where to begin that journey. Or is the kernel in use hamstrung from supporting that cpufreq option, and I would therefore be wasting my time pursuing it? I have successfully used the std 918+ 0.8_std ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_std with hardware transcoding active and functional on Pentium Anniversary G3258 MSI B85M-E45 board, and i3-9100 with Gigabyte Z390 Gaming X motherboard. Or have I missed something completely here, and I should be using the extra.lzma/extra2.lzma for loader 1.04b ds918+ DSM 6.2.3 v0.10 posted at the top of this topic more recently - I was coy because of the failure on both platforms with the syno 1.04b mod v0.8_syno but it may do away with the need for the three options completely? Thankyou for your efforts. Quote Link to comment Share on other sites More sharing options...
staratlas Posted April 29, 2020 Share #99 Posted April 29, 2020 11 hours ago, IG-88 said: as a newer mpt3sas.ko made no difference and jun's mpt3sys did not work i assumed the difference might be on level lower so i kept the new mpt3sas v27.0.0.1 and replaced my own new complied version (synology kernel source 24992) of scsi_transport_spi.ko, scsi_transport_sas.ko, raid_class.ko with the files from jun's original extra/extra2 test looks good, no problems loading mpt3sas and there are smart infos now Today, I tried this method, SMART info are fixed and were appeared in dsm, Thank you ! Quote Link to comment Share on other sites More sharing options...
richv31 Posted April 29, 2020 Share #100 Posted April 29, 2020 10 hours ago, ewgennt said: A regular non-multiplex controller (Espada PCIe4SATA3ASM) is inserted into the PCI-E 2.0 slot of the motherboard. But the system sees only 4 disks, 2 connected to the motherboard and 2 connected to the controller. If you connect one disk to the controller in turn in each slot, then it is visible in the system. This controller will not work - has a port multiplier chip, "SATA Controller Card --- Port Multiplier FIS-based and Command-based switching supported; Chipset: ASM 1061+1093.Added 2U (8CM/3.14in) half height bracket". Get a different one..... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.