jun

Progress of 6.2 loader

Polanskiman

Let me get things straighten up here before this thread starts going sideways. This is the developper discussion room. Not a newbie forum to start asking for guides and whatnot. @jun hasn't even said anything about the loader he has uploaded to his repository. So I would advise self control. Also, to those in panic mode trying to make things work desperately please use your personal jugement and experience. If you want to have a positive contribution to this thread then please do so by posting about possible bugs or things that don't work (beyond the "no network" boring posts of course). I am talking about serious bugs or the such. All other requests will from now on be deleted or moved if appropriate. I have no time to babysit anymore. Use the forum subsections.

Message added by Polanskiman

Recommended Posts

2 minutes ago, Ikyo said:

Unable to discover it and not showing on my network.  I have tried both the baremetal and VMware options from the Grub loader.

 

Processor: Intel(R) Xeon(R) CPU E5-2665 0 @ 2.40GHz

 

ESXI Version: 6.7

 

Host Config:

SATA Controller

e1000e Network Card

50mb boot (SATA0)

16gb test drive (SATA1)

 

please be more specific about what chip the nic is, at least the i217 seems to be a problem

if you cant check about the chip please give the product name of the nic or the system board (if its onboard)

 

Share this post


Link to post
Share on other sites
1 minute ago, IG-88 said:

 

please be more specific about what chip the nic is, at least the i217 seems to be a problem

if you cant check about the chip please give the product name of the nic or the system board (if its onboard)

 

It is using one of the internal Broadcom Gigabit Ethernet BCM5720 NICs and ESXI is emulating an e1000e.  I will go back and try the VMXNET3.

Share this post


Link to post
Share on other sites
5 minutes ago, Ikyo said:

It is using one of the internal Broadcom Gigabit Ethernet BCM5720 NICs and ESXI is emulating an e1000e.  I will go back and try the VMXNET3.

 

BCM5720 would be tg3 driver and thats part of juns extra.lzma. so the nic should work in baremetal

 

BUT you cpu is sandy bridge and that did not work with desktop processors on 918+ image so i'd expect it to fail because of the cpu (see my cpu list on page 5)

Share this post


Link to post
Share on other sites

I have actually gotten the NIC to show up on my switch, but it didn't get an IP address.  To get it to show up I switched from BIOS to EFI in the VMWare loader.  I am wondering if I am seeing the NIC register because of the way it is handled with EFI.

Share this post


Link to post
Share on other sites

Strange thing is, I have another nas server, and it has two i210 nic too. I installed dsm 6.1 on it with loader 1.02b, and it works perfectly. But the i210 nic's on acer C100F3 don't work. So maybe the problem is not the nic's driver.

Share this post


Link to post
Share on other sites
13 hours ago, IG-88 said:

 

BCM5720 would be tg3 driver and thats part of juns extra.lzma. so the nic should work in baremetal

 

BUT you cpu is sandy bridge and that did not work with desktop processors on 918+ image so i'd expect it to fail because of the cpu (see my cpu list on page 5)

 

what is not clear to me is if the cpu is currently not supported, it might be with an update of the loader (maybe based on bromolow like the previous one) or are we completely cut out?

Share this post


Link to post
Share on other sites
1 minute ago, simoareva said:

 

what is not clear to me is if the cpu is currently not supported, it might be with an update of the loader (maybe based on bromolow like the previous one) or are we completely cut out?

 

its about the original kernel used in the loader, its compiled with settings by synology to have a good support/performance with the used 918+ hardware (J3455), not to have a wide range of other hardware supported

as jun's approach is to use the kernel and dsm unmodded and circumvent the protection (check for certain hardware presence, signed drivers) we will have to live with the limits of the original kernel (among others no explicit amd cpu support, no hyper-v support), so the list about supported cpu's is for finding out where the limits are (drivers in most cases can be fixed, missing kernel option that need to be compiled into the kernel can't)

i started the cpu list because jun stated in his comments to 1.03a2 that its unknown for now what will be supported and also on what happened with the 1.02 916+ image, nobody could really say in what hardware the quick sync video transcoding support would work, we knew  min. 4th gen intel core to boot from jun an no one documented about the transcoding

 

as the 918+ has a newer kernel 4.x (and hopefully will support more hardware then the old kernel) i'm kind of "count me in" for the 918+

if you look into the 3615/3617 dsm 6.2 images you will see they still use the old 3.x kernel so no improvements are to expect in this area, kind of dead end as long as we find somone fixing the sata_ * and pata_* driver issue in the synology source (maybe we will have the same in kernel 4.x, we will soon find out)

  • Like 1

Share this post


Link to post
Share on other sites

Good afternoon.
Sorry for my English.
I run dsm 6.2 XPEnology on Thecus_n2800.
Synology Assistant - the device in the network sees, offers migration.

Formatting and partitioning of the disk is in progress. Splits the disk into 3 sections.
2 sections of 2 gigas each.
1 partition is the remaining space on the disk under the repository.

But.
DSM_DS918 + _23739.pat is not installed
The installation goes up to 57%, then an error message appears. (13)

 

installed and running XPEnoboot_DS3615xs_5.2

Показать содержимое  

Synology> lspci -kQ
00:00.0 Host bridge: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controller (rev 04)
        Subsystem: Intel Corporation Device 1999
00:02.0 VGA compatible controller: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller (rev 0b)
        Subsystem: Intel Corporation Device 1999
00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: uhci_hcd
00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: ehci-pci
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller
        Subsystem: Device 1c3d:1a1b
00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1
        Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2
        Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3
        Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 4
        Kernel driver in use: pcieport
00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5
        Kernel driver in use: pcieport
00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6
        Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: ehci-pci
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90)
00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller
        Subsystem: Device 1c3d:1a1b
        Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
        Subsystem: Device 1c3d:1a1b
01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
        Subsystem: Intel Corporation Device 0000
        Kernel driver in use: e1000e
02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
        Subsystem: Intel Corporation Device 0000
        Kernel driver in use: e1000e
05:00.0 USB controller: Renesas Technology Corp. uPD720202 USB 3.0 Host Controller (rev 02)
        Kernel driver in use: xhci_hcd
pcilib: Cannot write to /var/services/homes/admin/.pciids-cache: No such file or directory
 

Hide  

 

Edited by redika

Share this post


Link to post
Share on other sites

*ASROCK Q1900 ITX

#Intel J1900

tested to boot: NotWorking

 

 

Unbenannt.png

 

If no hard disk was connected (only the USB stick) then SynologyAssistant finds the server and the further installation fails because of the missing hard disk.

Once a SATA hard drive is connected at boot, the server can no longer be found by Synology Assistant

So is there a driver problem here?

Edited by Hyperbit
Add something
  • Like 1

Share this post


Link to post
Share on other sites

Hello, sorry for my bad english...

My ds3617xs on my ESXI 6.5 work very well with DSM 6.1.7-15284

But DS918+ dont have any ip adress with DSM 6.2 (E1000 or VMNEXT3).

My ESXI is a PowerEdge R710 (Old server of my office ;-))

his NIC is

QLogic Corporation QLogic NetXtreme II BCM5709 1000Base-T

Good luck to run DSM 6.2...

Bye

Julien

Share this post


Link to post
Share on other sites

System Tested:

 

     Shuttle SZ170R8 V2

     CPU:  i5-7600K

     Memory:  16 gb DDR4

     Network 1:  intel i219

     Network 2:  intel i211

     Network 3:  Ugreen PCI Express Network Adapter using Realtek RTL8111G chip

 

When booting with jun's 1.03a2 DS918p image I get the following kernel panic.

 

Spoiler

                   GNU GRUB  version 2.02~beta2-36ubuntu3.14                                                            
 +----------------------------------------------------------------------------+                                                                               
 |*DS918+ 6.2 Baremetal with Jun's Mod v1.03a                                 |                                                                               
 | DS918+ 6.2 Baremetal with Jun's Mod v1.03a Reinstall                       |                                                                               
 | DS918+ 6.2 VMWare/ESXI with Jun's Mod v1.03a                               |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 |                                                                            |                                                                               
 +----------------------------------------------------------------------------+                                                                               
      Use the ^ and v keys to select which entry is highlighted.                                                                
      Press enter to boot the selected OS, `e' to edit the commands                                                                   
      before booting or `c' for a command-line.                                               

[    0.001093] Spectre V2 : kernel not compiled with retpoline; no mitigation                                                             
available!          
[    1.214533] ata1: send port disabled event                                             
[    1.231424] ata2: send port disabled event                                             
patching file etc/rc                    
patching file etc/synoinfo.conf                               
patching file linuxrc.syno                          
patching file usr/sbin/init.post                                
START /linuxrc.syno                   
Insert basic USB modules...                           
:: Loading module usb-common ... [  OK  ]                                         
:: Loading module usbcore ... [  OK  ]                                      
:: Loading module ohci-hcd ... [  OK  ]                                       
:: Loading module xhci-hcd ... [  OK  ]                                       
:: Loading module xhci-pci ... [  OK  ]                                       
:: Loading module usb-storage ... [  OK  ]                                          
:: Loading module BusLogic ... [  OK  ]                                       
:: Loading module vmw_pvscsi ... [  OK  ]                                         
:: Loading module megaraid_mm ... [  OK  ]                                          
:: Loading module megaraid_mbox ... [  OK  ]                                            
:: Loading module scsi_transport_spi ... [  OK  ]                                                 
:: Loading module mptbase ... [  OK  ]                                      
:: Loading module mptscsih ... [  OK  ]                                       
:: Loading module mptspi ... [  OK  ]                                     
:: Loading module mptctl ... [  OK  ]                                     
:: Loading module megaraid ... [  OK  ]                                       
:: Loading module megaraid_sas ... [  OK  ]                                           
:: Loading module mdio ... [  OK  ]                                   
Insert net driver(Mindspeed only[    3.696559] BUG: unable to handle kernel NULL                                                                 
 pointer dereference at 0000000000000090                                        
[    3.705873] IP: [<ffffffff813f0c5f>] syno_ahci_disk_led_enable+0x7f/0x170                                                                            
[    3.713031] PGD 455d73067 PUD 453a96067 PMD 0                                                
[    3.717775] Oops: 0002 [#1] PREEMPT SMP                                          
[    3.721961] Modules linked in: apollolake_synobios(PO+) etxhci_hcd mdio(E) me                                                                                
garaid_sas(E) megaraid(E) mptctl(E) mptspi(E) mptscsih(E) mptbas                                                               
ort_spi(E) megaraid_mbox(E) megaraid_mm(E) vmw_pvscsi(E) BusLogic(E) usb_storage                                                                                
 xhci_pci xhci_hcd ohci_hcd(E) usbcore usb_common irsnlpnkiootka(OE)                                                                    
[    3.750763] CPU: 0 PID: 3678 Comm: insmod Tainted: P           OE   4.4.59+ #                                                                                
23739     
[    3.758727] Hardware name: Shuttle Inc. SZ170/FZ170, BIOS 2.09 08/01/2017                                                                            
[    3.765857] task: ffff880084849000 ti: ffff88045a87c000 task.ti: ffff88045a87                                                                                
c000    
[    3.773718] RIP: 0010:[<ffffffff813f0c5f>]  [<ffffffff813f0c5f>] syno_ahci_di                                                                                
sk_led_enable+0x7f/0x170                        
[    3.783428] RSP: 0018:ffff88045a87fb90  EFLAGS: 00010046                                                           
[    3.789020] RAX: 0000000000000000 RBX: ffff880085270000 RCX: 0000000000000000                                                                  
[    3.796529] RDX: 0000000000000000 RSI: ffff880085270000 RDI: 0000000000000008                                                                  
[    3.804044] RBP: ffff88045a87fbc0 R08: 0000000000000000 R09: 00000000000024c0                                                                  
[    3.811560] R10: 0000000000002640 R11: 0000000000002640 R12: 0000000000000000                                                                  
[    3.819086] R13: ffff880456c2f000 R14: 0000000000000001 R15: ffff880085271f40                                                                  [    3.826593] FS:  00007f625b24c700(0000) GS:ff 00000000000           
[    3.835079] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033                                                                
[    3.841122] CR2: 0000000000000090 CR3: 00000004592cb000 CR4: 00000000003606f0                                                                  
[    3.848628] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000                                                                  
[    3.856120] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400                                                                  
[    3.863627] Stack:                     
[    3.865762]  0000000000000286 ffffffff8180e040 ffff8804510b9500 0000000000000                                                                                
000   
[    3.873632]  ffffffffa01495f0 ffff88008580eec0 ffff88045a87fcb8 ffffffffa014d                                                                                
14c   
[    3.881477]  ffff88045c83c248 0000000000000000 0000000000000282 ffff88045a87f                                                                                
c20   
[    3.889322] Call Trace:                          
[    3.891900]  [<ffffffffa01495f0>] ? remove_card_detect_proc+0x20/0x20 [apollo                                                                                
lake_synobios]              
[    3.900734]  [<ffffffffa014d14c>] synobios_model_init+0xec/0x650 [apollolake_                                                                                
synobios]         
[    3.909056]  [<ffffffff812b63ff>] ? ida_pre_get+0x4f/0xe0                                                            
[    3.914760]  [<ffffffff8119da2d>] ? proc_alloc_inum+0x3d/0xc0                                                                
[    3.920810]  [<ffffffff8119dba9>] ? proc_register+0xb9/0x110                                                               
[    3.926768]  [<ffffffffa01495f0>] ? remove_card_detect_proc+0x20/0x20 [apollo                                                                                
lake_synobios]              
[    3.935575]  [<ffffffff8119dd12>] ? proc_mkdir_data+0x62/0x90                                                                
[    3.941633]  [<ffffffff8119dd60>] ? proc_mkdir+0x10/0x20                                                           
[    3.947237]  [<ffffffffa0149663>] synobios_init+0x73/0x470 [apollolake_synobi                                                                                
os]   
[    3.955011]  [<ffffffff810003b6>] do_one_initcall+0x86/0x1b0                                                               
[    3.960976]  [<ffffffff810df1d8>] do_init_module+0x56/0x1be                                                              
[    3.966847]  [<ffffffff810b554d>] load_module+0x1ded/0x2070                                                              
[    3.972714]  [<ffffffff810b28b0>] ? __symbol_put+0x50/0x50                                                             
[    3.978512]  [<ffffffff81112da5>] ? map_vm_area+0x35/0x50                                                            
[    3.984209]  [<ffffffff811140ec>] ? __vmalloc_node_range+0x13c/0x240                                                                       
[    3.990902]  [<ffffffff810b5858>] ? SYSC_init_module+0x88/0x110                                                                  
[    3.997136]  [<ffffffff810b58cf>] SYSC_init_module+0xff/0x110                                                                
[    4.003178]  [<ffffffff810b5969>] SyS_init_module+0x9/0x10                                                             
[    4.008970]  [<ffffffff81566b17>] entry_SYSCALL_64_fastpath+0x12/0x6a                                                                        
[    4.015756] Code: e8 97 7b fd ff 48 85 c0 4c 8d 38                                                     
 24 48 89 d0 48 83 c7 08 48 c1 e0 02 48 01 d0 48 c1 e0 04 4a 8d 04 20 <48> c7 80                                                                                
 90 00 00 00 00 00 00 00 48 c7 80 88 00 00 00 00 00 00                                                      
[    4.036936] RIP  [<ffffffff813f0c5f>] syno_ahci_disk_led_enable+0x7f/0x170                                                                             
[    4.044182]  RSP <ffff88045a87fb90>                                      
[    4.047857] CR2: 0000000000000090                                    
[    4.051344] ---[ end trace ac98f6d41e7a4163 ]---                                                   
[    4.056207] note: insmod[3678] exited with preempt_count 1                                                             
)...    
Killed      
Starting /usr/syno/bin/synocfgen...                                   
/usr/syno/bin/synocfgen returns 255                                   
rmmod: can't unload 'apollolake_synobi[    4.072258] md: Autodetecting RAID arra                                                                                
ys.   
os': Device or r[   21.587290] NMI watchdog: Watchdog detected hard LOCKUP on cp                                                                                
u 0   
[   21.593438] Modules linked in: apollolake_synobios(PO+) etxhci_hcd mdio(E) me                                                                                
garaid_sas(E) megaraid(E) mptctl(E) mptspi(E) mptscsih(E) mptbase(E) scsi_transp                                                                                
ort_spi(E) megaraid_mbox(E) megaraid_mm(E) vmw_pvscsi(E) BusLogic(E) usb_storage                                                                                
 xhci_pci xhci_hcd ohci_hcd(E) usbcore usb_common irsnlpnkiootka(OE)                                                                    
[   21.622393] CPU: 0 PID: 3706 Comm: mdadm Tainted: P      D    OE   4.4.59+ #2                                                                                
3739    
[   21.630263] Hardware name: Shuttle Inc. SZ170/FZ170, BIOS 2.09 08/01/2017                                                                            
[   21.637398] task: ffff880452992f00 ti: ffff880452ae0000 task.ti: ffff880452ae                                                                                
0000    
[   21.645261] RIP: 0010:[<ffffffff81082828>]  [<ffffffff81082828>] queued_spin_                                                                                
lock_slowpath+0x148/0x160                         
[   21.655059] RSP: 0018:ffff880452ae3a58  EFLAGS: 00000002                                                           
[   21.660641] RAX: 0000000000000101 RBX: 0000000000000293 RCX: 0000000000000101                                                                  
[   21.668156] RDX: 0000000000000101 RSI: 0000000000000001 RDI: ffff880455c11718                                                                  
[   21.675673] RBP: ffff880452ae3a58 R08: 0000000000000001 R09: ffffffffffffffc0                                                                  
[   21.683196] R10: ffff8804529edf88 R11: 0000000000000000 R12: ffff880459a21000                                                                  
[   21.690704] R13: ffff8800376fc000 R14: ffff880459a21050 R15: ffff88045955a6c0                                                                  
[   21.698206] FS:  00007fc0e8e23700(0000) GS:ffff88046ec00000(0000) knlGS:00000                                                                                
00000000000           
[   21.706700] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033                                                                
[   21.712743] CR2: 0000000001f66328 CR3: 000000045394c000 CR4: 00000000003606f0                                                                  
[   21.720259] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000                                                                  
[   21.727766] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400                                                                  
[   21.735248] Stack:                     
[   21.737372]  ffff880452ae3a70 ffffffff8156675b ffff88045955a6c0 ffff880452ae3                                                                                
aa0   
[   21.745225]  ffffffff813d6b71 ffff88045955a6c0 ffff88045642b000 ffff88044cd5c                                                                                
9a0   
[   21.753081]  ffff880459a21050 ffff880452ae3ac0 ffffffff813a73ab ffff880459a21                                                                              
000   
[   21.760918] Call Trace:                          
[   21.763501]  [<ffffffff8156675b>] _raw_spin_lock_irqsave+0x2b/0x40                                                                     
[   21.769997]  [<ffffffff813d6b71>] ata_scsi_queuecmd+0x21/0x440                                                                 
[   21.776107]  [<ffffffff813a73ab>] scsi_dispatch_cmd+0xfb/0x380                                                                 
[   21.782269]  [<ffffffff813a8e1e>] scsi_request_fn+0x3be/0x580                                                                
[   21.788333]  [<ffffffff81291b1e>] __blk_run_queue+0x2e/0x40                  
[   21.794192]  [<ffffffff81295ed5>] blk_queue_bio+0x2b5/0x2c0
[   21.800070]  [<ffffffff81294181>] generic_make_request+0xd1/0x1d0
[   21.806485]  [<ffffffff81294302>] submit_bio+0x82/0x160
[   21.811999]  [<ffffffff8128d722>] submit_bio_wait+0x52/0x70
[   21.817851]  [<ffffffff8144c585>] read_disk_sb.constprop.81+0x85/0x170
[   21.824718]  [<ffffffff8144c6b9>] super_90_load+0x49/0x400
[   21.830499]  [<ffffffff8116e0c3>] ? blkdev_get_by_dev+0x33/0x50
[   21.836723]  [<ffffffff81443a8f>] ? lock_rdev+0x2f/0x80
[   21.842228]  [<ffffffff81448312>] md_import_device+0x152/0x230
[   21.848376]  [<ffffffff8144f84c>] md_ioctl+0x31c/0x1fa0
[   21.853874]  [<ffffffff8114d06c>] ? dput+0x5c/0x250
[   21.858995]  [<ffffffff812a29bf>] blkdev_ioctl+0x5ff/0x900
[   21.864777]  [<ffffffff8116cd28>] block_ioctl+0x38/0x40
[   21.870263]  [<ffffffff811490f3>] do_vfs_ioctl+0x463/0x940
[   21.876054]  [<ffffffff81144efb>] ? do_unlinkat+0xcb/0x2d0
[   21.881828]  [<ffffffff8114964a>] SyS_ioctl+0x7a/0x90
[   21.887179]  [<ffffffff81566b17>] entry_SYSCALL_64_fastpath+0x12/0x6a
[   21.893990] Code: 01 48 8b 02 48 85 c0 75 0a f3 90 48 8b 02 48 85 c0 74 f6 c7
 40 08 01 00 00 00 e9 51 ff ff ff 83 fa 01 75 07 e9 4e ff ff ff f3 90 <8b> 07 84
 c0 75 f8 66 c7 07 01 00 5d c3 66 2e 0f 1f 84 00 00 00
[   21.915136] Kernel panic - not syncing: Hard LOCKUP
[   21.920260] Kernel Offset: disabled
[   21.923936] ---[ end Kernel panic - not syncing: Hard LOCKUP
 
 
Edited by Polanskiman
Added code and spoiler tag.

Share this post


Link to post
Share on other sites
8 hours ago, redika said:

I run dsm 6.2 XPEnology on Thecus_n2800.
Synology Assistant - the device in the network sees, offers migration.

Formatting and partitioning of the disk is in progress. Splits the disk into 3 sections.
2 sections of 2 gigas each.
1 partition is the remaining space on the disk under the repository.

But.
DSM_DS918 + _23739.pat is not installed
The installation goes up to 57%, then an error message appears. (13)

 

i've see that with my Avoton C2550 cpu too, everything was right (usb vid/pid) but install failed, so i did tried the same usb flash drive with a skylake system and after insalling i connected the disk and usb flash drive to to the avoton system and it came up nicely

your cpu is older then the avoton, its Cedarview Q3/2011, your nic is e1000 driver and thats inside juns loader already, so maybe it will work if you install it on a different system and then use the disk on the thecus, as this is pretty early i would not advise to do it on a system you need for daily use, it could be that if a update comes up that it will not install cleanly, we would need more time to see waht happens with major updates like 6.2.(0)->6.2.1

Share this post


Link to post
Share on other sites
5 hours ago, Hyperbit said:

ASROCK Q1900 ITX

#Intel J1900

tested to boot: NotWorking

 

5 hours ago, Hyperbit said:

If no hard disk was connected (only the USB stick) then SynologyAssistant finds the server and the further installation fails because of the missing hard disk.

Once a SATA hard drive is connected at boot, the server can no longer be found by Synology Assistant

So is there a driver problem here?

 

hmm, the fact that it coems up without a disc idicates the kernel and realtek network driver are working,, that board has 2x intel onboard (ahci) and 2 ports ASMedia ASM1061, also ahci with kernel 4.x (https://cateee.net/lkddb/web-lkddb/SATA_AHCI.html)

maybe you can try disabling the asmedia in bios for testing? or try installing 6.2 on a different system and after installing use flash drive and hdd on th Q1900

Share this post


Link to post
Share on other sites
4 hours ago, juju78y said:

My ds3617xs on my ESXI 6.5 work very well with DSM 6.1.7-15284

But DS918+ dont have any ip adress with DSM 6.2 (E1000 or VMNEXT3).

My ESXI is a PowerEdge R710 (Old server of my office ;-))

his NIC is

QLogic Corporation QLogic NetXtreme II BCM5709 1000Base-T

 

the nic might be a problem in barematal as jun does no provide all firmware files in his extra.lzma but in vm it not relevant, if you use vmxnet then there is a driver in juns extra.lzma

the processor might be the problem if it E5520 or simmilar the its Nehalem EP Q1/2009 and thats way older then the 4th gen intel core desktop cpu we have found as working min, yet (see my list on page 5), so not likely to work (on the other hand no gain with 918+ image, dsm 6.1 works stable so why using 6.2, nothing to win a lot to loose)

 

 

Share this post


Link to post
Share on other sites
3 hours ago, FiberInternetUser said:

Shuttle SZ170R8 V2

     CPU:  i5-7600K

     Memory:  16 gb DDR4

     Network 1:  intel i219

     Network 2:  intel i211

     Network 3:  Ugreen PCI Express Network Adapter using Realtek RTL8111G chip

 

we already have

Core i7-7700, 4 cores, 3.6 GHz base, 4.2 GHz burst, HD Graphics 630, Kaby Lake, Q1/2017

as working so it should work from the cpu side, we already had reports for i217 not to work, maybe i219 is causing trouble too

try to disable/remove all adaters, just leave one active and try with just one and if it fails try with another

 

 

Share this post


Link to post
Share on other sites
1 hour ago, IG-88 said:

 

we already have

Core i7-7700, 4 cores, 3.6 GHz base, 4.2 GHz burst, HD Graphics 630, Kaby Lake, Q1/2017

as working so it should work from the cpu side, we already had reports for i217 not to work, maybe i219 is causing trouble too

try to disable/remove all adaters, just leave one active and try with just one and if it fails try with another

 

 

 

I disabled/removed each adapter one at a time.  With the Ugreen using the RealTek RTL8111G chip, the boot process proceeded a little further.  I still get the crash at the start but modules continuing loadiing.  It loads OK the " :: Loading modul[    6.349374] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [    6.357725] e1000: Copyright (c) 1999-2006 Intel Corporation. e e1000 ... [   OK   ].

 

The boot process stops at :: Loading module synobios  ..

Share this post


Link to post
Share on other sites

does it show up in network after loading the realtek driver?

Share this post


Link to post
Share on other sites
11 minutes ago, IG-88 said:

does it show up in network after loading the realtek driver?

 

No, as I don't think the boot process completed correctly.  Usually, with a normal boot using the older 6.1 DS3617xs image the boot completes with "Diskstation Login".  At that point I can login through the serial port.   When booting the 918+ image it has problems with one module and performs a trace, the boot continues and states network modules are loading ok but the boot process stops at the Loading module synobios ... does not complete to "Diskstation Login".

 

I disabled both internal NIC's and I installed another network card which has a Realtek RTL8111E chip.  Same results.  I can't determine what module the boot process is having a problem with.  Thanks for your help.

Share this post


Link to post
Share on other sites

VMWare Workstation:14.1.2 

Hardware compatibility: 14x Workstation

VM Config:

SATA Controller

Network: Bridged

50mb boot (SATA0)

8gb test drive (SATA1)

 

image.png.7cda07e3208956a1d195ea146d1fabba.png

Capture.thumb.PNG.f3736004dff4dd95cb6d361f267b0399.PNG

 

Why 12 disks on 918+?

Capture1.thumb.PNG.f5b08d3d247910718887dc7ef85ebc61.PNG

 

root access needs additionally jumping through hoops... wish the VERSION on the boot image was not set higher than 6.1.7

Edited by modboxx

Share this post


Link to post
Share on other sites
Il y a 4 heures, modboxx a dit :

VMWare Workstation:14.1.2 

Hardware compatibility: 14x Workstation

VM Config:

SATA Controller

Network: Bridged

50mb boot (SATA0)

8gb test drive (SATA1)

 

image.png.7cda07e3208956a1d195ea146d1fabba.png

Capture.thumb.PNG.f3736004dff4dd95cb6d361f267b0399.PNG

 

Why 12 disks on 918+?

Capture1.thumb.PNG.f5b08d3d247910718887dc7ef85ebc61.PNG

 

root access needs additionally jumping through hoops... wish the VERSION on the boot image was not set higher than 6.1.7

Did you edit synology.img to run DSM ?

Share this post


Link to post
Share on other sites
41 minutes ago, agent47SG1 said:

Did you edit synology.img to run DSM ?

Yes.  SN/mac

Share this post


Link to post
Share on other sites
5 hours ago, modboxx said:

VMWare Workstation:14.1.2 

Hardware compatibility: 14x Workstation

VM Config:

SATA Controller

Network: Bridged

50mb boot (SATA0)

8gb test drive (SATA1)

 

you don't write anything about your hardware, at least cpu should be mentioned

5 hours ago, modboxx said:

Why 12 disks on 918+?

 

because its kind of common for 3615/3617 and a good ammount of people user more then the 4 disk default, it sprare's tjem tinkering inf if you use less it does not hurt

 

5 hours ago, modboxx said:

root access needs additionally jumping through hoops...

you can activate root (as user), use the search, beside this whats wrong with sudo or just once sudo su

 

5 hours ago, modboxx said:

 

wish the VERSION on the boot image was not set higher than 6.1.7

 

??? if you dont want 6.2 use loader 1.02 and dsm 6.1(.7)

 

Share this post


Link to post
Share on other sites
38 minutes ago, IG-88 said:

 

you don't write anything about your hardware, at least cpu should be mentioned

 

I did not know there was a specific criteria required? I see people posting what they think they should?  Tell me what you want and I will, no need to get sassy

 

It's on a j3455

Quote

 

because its kind of common for 3615/3617 and a good ammount of people user more then the 4 disk default, it sprare's tjem tinkering inf if you use less it does not hurt

I should have been more specific.  The patch changes max disk to 12 and adds an additional 4 disks to internalportcfg but that's still 8.  The reason I asked was because when I did a remap of the first disk it didn't show up which was even more confusing.  Additionally, sataportmap is only set to 4.  0c will kernel panic 

 

Quote

 

you can activate root (as user), use the search, beside this whats wrong with sudo or just once sudo su

I thought this was a dev forum where people can come and complain about the new awesomely annoying "Features" Synology added? 

 

if you are referring to synouser? that longer works by itself, have to do more, the one I picked was to add no NOPASSWD but that means no pass prompt on sudo su.

 

Going back as why not just ...It's really just a matter of convenience with winscp.

 

Quote

??? if you dont want 6.2 use loader 1.02 and dsm 6.1(.7)

918+ has a lot more goodies, you know that.

Edited by modboxx

Share this post


Link to post
Share on other sites

I just tried the DS918p 6.2-23739 Update 1 on a baremetal ASRock J3455-ITX using Jun's 1.03a2 loader and after the automatic reboot, the update experienced a kernel panic.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.