Leaderboard

Good explaining about SataPortMap https://11q.kr/www/bbs/board.php?bo_table=s11&wr_id=11263&sst=wr_datetime&sod=desc&sop=and&page=3 use English translation with Google chrome when you check this page.. there are lot more stuff. ESXi config instruction etc.

Невнимательны. Это Вы скачали для RS3617. А вам нужен файл DSM_DS3617xs_15047

У Вас же внизу на картинке написано, что нужен файл для DS3617, а Вы ему подсовываете для DS111. Скачайте правильный.

Okay, for those who cannot install DSM918+ 7.0 in baremetal. Seem like I had found the solution. This should fix for those who keep stuck at 40% or 55% with error message. NOTE: As tested with legacy and UEFI boot. I only manage to fix it with legacy boot. Require tool: telnet / serial com (I am using telnet). Reminder, telnet will only start when installation failed. Which mean when you see the error message appear during DSM installation, you can start to initial telnet to your PC. I tested at my laptop, now successfully run DSM7.0 First: Make sure you have your PID and VID right. When install failed, telnet to your computer. run: fdisk -l Make sure it detect your internal HDD. If yes then check whether do you have /dev/synoboot1, /dev/synoboot2 and /dev/synoboot3 If you don't see /dev/synoboot* then this solution will most likely work. Now, remove your USB and plugin to another available USB port of your PC. run fdisk -l again. See what new devices appear. If you see /dev/synoboot* appear then proceed to install the DSM pat file, it will pass. If you see /dev/sdx then it might be your PID and VID is wrong, please check it properly. If you don't see any device appear then try another USB port and repeat the step above. If you had tried all USB ports but still don't have devices appear then check your BIOS setting. Make sure USB debug is off. Just turn on the minimum USB support in order to allow BIOS boot from USB. Good luck. I am going to test in my another PC soon.

with uefi support. redpill-load.win.zip.001redpill-load.win.zip.002 it also can support dsm 7.0.1

I have some findings after doing a little research and adjusting settings, it looks like I found the sweet spot for power draw and performance, as well as having functioning WOL, lower fan speed, and as an added bonus HDD's going to sleep! I am using the very latest Latest Service Pack 2018.09.0 (P03093_001_spp-Gen8.1-SPPGen81.4.iso) with all firmware updates and current iLO. HPE decided you needed a warranty to get the download, let's not muck about with that: Download here I set the iLO time manually to a time server under Network>iLO Dedicated Network Port>SNTP Propagate NTP time to host. Unchecked use DHCPv4 and DHCPv6. I don't use IPv6 so I have that disabled, and under IPv4 I have ping gateway on startup unchecked. My WINS server is my router, if this is pointing to your XPEnology then there might be a sleep wake problem for hibernation of disks (more on that later.) I also don't have a shared network port enabled under iLO. The iLO network tweaks are probably not required but it improved my configuration. Third thing you may want to double check after firmware is that your BIOS settings are set correctly including the correct time: System Options> Embedded NICs: Network boot disabled for both (unless you PXE boot from the Network) USB Options>Removable Flash Media Boot Sequence: Internal DriveKeys First (that is where XPEnology lives) SATA Controller Options>Embedded SATA Configuration: Enable SATA AHCI Support SATA Controller Options>Drive Write Cache: Disabled Power Management Options> HP Power Profile: Set to Custom HP Power Regulator: OS Control Mode Power Management Options>Advanced Power Management Options: Intel QPI Link Power Management: Enabled Minimum Processor Idle Power Core State: C1E State Minimum Processor Idle Power Package State: Package C6 (retention) State Maximum Memory Bus Frequency: I set mine to 1333MHz (This depends on your RAM) Memory Interleaving: Full Interleaving PCI-E Gen 3 Control: I disabled mine because I have no use for it, helps with power draw. If you have something plugged in don't disable. Dynamic Power Savings Mode Response: Fast Collaborative Power Control: Enabled DIMM Voltage Preference: Optimized for Power, again this depends on your RAM Server Availability> Wake-On LAN: Enabled Thermal Shutdown: Enabled Power Button: Enabled Automatic Power-On: Restore Last Power State Advanced Options>Advanced System ROM Options> MPS Table Mode: Full Table APIC Power-On Logo: Disabled, it speeds up the bootup time and still has a prompt for F9 to get into BIOS. Leave everything else alone or set to your specific preferences if you know what you are doing, double check the BIOS date and time and then save your settings to get back into DSM. DSM settings: There are a lot of things that can affect your overall power draw and performance to keep your drives from properly going to sleep, read this page to understand the implications of certain packages. Control Panel> Regional Options>Time: Set the correct time zone, and click update now. Don't worry about NTP Service unless you use Surveillance Station. Performance: Uncheck Memory Compression. Will trigger a reboot. Hardware & Power> General: Everything is ticked, except the Fan Speed Mode. Power Schedule: Leave this alone for now. HDD Hibernation: I do 10 Minutes on both and enable Hibernation logs. Not checking Enable auto poweroff for now. Info Center> Service: Double check you don't have anything running that could affect sleep and wake, for example SMB is the only service running but it could act as a Master Browser which would affect the hibernation so I have it disabled. Another thing I prefer to do on my box is completely remove Universal Search: SSH into the NAS and run these commands: sudo -s synopkg uninstall SynoFinder I don't have any media indexing going on but that may be a factor as well. Other thoughts: Splitting up your hard drive disk groups could have an effect on what your hibernation looks like, check the logs, about half your drives may hibernate while others won't, it depends on the services running and many other factors that are far too much to name here. If you want the unit to go into a complete power off/on state try a package called Advanced Power Manager. I swear by this package and confirmed that it works on both my DS216+II, and XPEnology bare metal Gen8. There are many advanced functions that you can tweak that affect how your NAS "Sleeps" so explore it. Wake-on-LAN works if I have the unit go into an auto-poweroff state, but I use my Router to send a wake request to get it back up to where it was. I am using BTRFS but have not noticed any overworked HDD's crunching data into the night, everything remains stable and quiet and my fan speeds have gone down to 19% and idle is sitting well below 39w. Did I mention time is a factor to your hibernation? Make sure that your BIOS time and Synology DSM times are in sync, otherwise your 10 minute hibernation will never happen. I hope I helped somebody in these forums, and answered my own question at the same time.

Hi @ThorGroup, not heard from you guys for three weeks now, here or Github. You okay? Some of us are getting a little worried that Something Bad™ happened. Hope things are good, shout out if there's anything we can do to help (generally, not just regarding RedPill, okay?). Just say "hi" if you're still around and too busy/have other things on...