Grush Posted June 24, 2022 Share #626 Posted June 24, 2022 On 6/1/2022 at 2:03 PM, use-nas said: 920 нужно пробовать. В общем дела такие. 920 поставился, но видит только один диск из трёх. Другие варианты хоть убей никак не вышло. Через виртуализацию осталось пробовать наверное, есть шансы что взлетит через ESXI? Quote Link to comment Share on other sites More sharing options...
Demitsuri Posted June 24, 2022 Share #627 Posted June 24, 2022 (edited) 1 час назад, Grush сказал: В общем дела такие. 920 поставился, но видит только один диск из трёх. Другие варианты хоть убей никак не вышло. Через виртуализацию осталось пробовать наверное, есть шансы что взлетит через ESXI? Тоже мучился с 920 загрузчиком. На голом железе видит только родной SATA - контроллер. В моем случае 2 диска... При этом в консоли через ssh диски есть. OS (в смысле webGUI) их не видит... 918 нормально всё видит. Edited June 24, 2022 by Demitsuri Комментарий Quote Link to comment Share on other sites More sharing options...
Demitsuri Posted June 24, 2022 Share #628 Posted June 24, 2022 В 20.06.2022 в 07:58, robin2368 сказал: В общем я записываю образ ( tinycore-redpill.v0.8.0.0.img.gz ) через rufus предварительно разорхивировав его, далее вставляю флешку с записанным образом в хрень, гружусь с этой флешки. В руфусе можно не разархивировать образ. Он сам tar.gz нормально запишет. Проверено на относительно свежей версии. Quote Link to comment Share on other sites More sharing options...
Grush Posted June 24, 2022 Share #629 Posted June 24, 2022 1 hour ago, Demitsuri said: 918 нормально всё видит. Да я вообще хотел DVA3221. Чтоб третью камеру можно было подключить. 918 пробовал, у меня он диски не видит никак. Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 25, 2022 Author Share #630 Posted June 25, 2022 В 23.06.2022 в 11:25, Focusnik сказал: Привет Поставил DSM 7.1-42661 на виртуалку VirtualBox А как туда подкинуть физический SSD ? В гугле забанили ) печалька... Quote Link to comment Share on other sites More sharing options...
Wodooo Posted June 26, 2022 Share #631 Posted June 26, 2022 Кто может направить на путь истинный !?) Сейчас стоит "DSM 7.0.1-42218 Update 2" всё настроено и работает, как безболезнее обновиться до 7.1.0-42661 ? Quote Link to comment Share on other sites More sharing options...
masyama Posted June 26, 2022 Share #632 Posted June 26, 2022 (edited) Здравствуйте. установил систему, всё хорошо работает, вот только при включении nas грузится около 10 минут. Если подключить моник, то видно, что всё грузится буквально 20 секунд, но доступ к нас (загорается зелёная лампочка на сетёвке) появляется минут через 10. Как ускорить это время? И второй вопрос: на 6.2 вншний доступ настраивался автоматом, а тут я уже замучился настраивать. Как настроить, подскажите пожалуйста. система 7.1.0-42661 конфиг j3455b-itx Edited June 26, 2022 by masyama Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 26, 2022 Author Share #633 Posted June 26, 2022 4 часа назад, masyama сказал: И второй вопрос: на 6.2 вншний доступ настраивался автоматом, а тут я уже замучился настраивать. Как настроить, подскажите пожалуйста. Не совсем понял вопрос, конкретизируйте, плиз... вроде ничего не поменялось. Quote Link to comment Share on other sites More sharing options...
masyama Posted June 26, 2022 Share #634 Posted June 26, 2022 35 минут назад, Olegin сказал: Не совсем понял вопрос, конкретизируйте, плиз... вроде ничего не поменялось. На прошивке 6.2 зашёл в настройки и там на автомате всё настроилось и внешний доступ появился (у меня белый ip). На 7.1 делаю всё то же самое, а он пишет, что данный роутер не поддерживает автоматическую настройку, делайте всё руками на роутере. Я делаю, а ничего не получается (возможно неправильно пробрасываю порты). Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 26, 2022 Author Share #635 Posted June 26, 2022 (edited) 18 минут назад, masyama сказал: На прошивке 6.2 зашёл в настройки и там на автомате всё настроилось и внешний доступ появился (у меня белый ip). На 7.1 делаю всё то же самое, а он пишет, что данный роутер не поддерживает автоматическую настройку, делайте всё руками на роутере. Я делаю, а ничего не получается (возможно неправильно пробрасываю порты). Скрытый текст Но я этим не пользуюсь проброшен внешний 443 на хрень 5001. Edited June 26, 2022 by Olegin Quote Link to comment Share on other sites More sharing options...
bboott Posted June 26, 2022 Share #636 Posted June 26, 2022 Спасибо автору, попробовал на чистом винте установить, все получилось, потом по инструкции с прошлой страницы, обновился до последнего апдейта. Серийник и мак с реального 918, QC работает (хоть и не пользуюсь) Подскажите пожалуйста, вот что заметил, на 6 версии системы, почти всегда показывало "Систему" в районе 40-45 градусов, а тут заметил что показывает 57-63. Не наблюдали у себя похожего? Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 26, 2022 Author Share #637 Posted June 26, 2022 22 минуты назад, bboott сказал: Спасибо автору, попробовал на чистом винте установить, все получилось, потом по инструкции с прошлой страницы, обновился до последнего апдейта. Серийник и мак с реального 918, QC работает (хоть и не пользуюсь) Подскажите пожалуйста, вот что заметил, на 6 версии системы, почти всегда показывало "Систему" в районе 40-45 градусов, а тут заметил что показывает 57-63. Не наблюдали у себя похожего? Есть такое - забил. 1 Quote Link to comment Share on other sites More sharing options...
Razoon Posted June 27, 2022 Share #638 Posted June 27, 2022 Господа, загрузчик собрал загрузчик вставил один диск, DSM говорит что дисков нет. tc@box:~$ lsscsi [1:0:0:0] disk ATA ST3000DM001 CC25 /dev/sda [6:0:0:0] disk USB SanDisk 3.2Gen1 1.00 /dev/sdb tc@box:~$ lspci -nnq 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge DRAM Controller [8086:0158] (rev 09) 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09) 00:06.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:015d] (rev 09) 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) 00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 [8086:1c1a] (rev b5) 00:1c.6 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 [8086:1c1c] (rev b5) 00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5) 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) 00:1f.0 ISA bridge [0601]: Intel Corporation C206 Chipset Family LPC Controller [8086:1c56] (rev 05) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF108 [GeForce GT 630] [10de:0f00] (rev a1) 01:00.1 Audio device [0403]: NVIDIA Corporation GF108 High Definition Audio Controller [10de:0bea] (rev a1) 02:00.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. 88SE6440 SAS/SATA PCIe controller [11ab:6440] (rev 02) 03:00.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. 88SE6440 SAS/SATA PCIe controller [11ab:6440] (rev 02) 04:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] 05:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] 06:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] 07:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] При этом TC говорит что на портах 5,6 есть ошибки, загрузчик собираю с игнорированием ошибокt tc@box:~$ sudo ./rploader.sh satamap now�[J Found SCSI HBAs, We need to install the SCSI modules Don't run this as root. Found "00:1f.2 Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 05)" Detected 6 ports/1 drives. Bad ports: 5 6. Override # of ports or ENTER to accept <6> 5,6� �� � 6 Non-numeric, overridden to 0 Found SCSI/HBA "02:00.0 Marvell Technology Group Ltd. 88SE6440 SAS/SATA PCIe controller (rev 02)" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid bus number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) Found SCSI/HBA "03:00.0 Marvell Technology Group Ltd. 88SE6440 SAS/SATA PCIe controller (rev 02)" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid bus number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) Computed settings: SataPortMap=1 DiskIdxMap=00 Should i update the user_config.json with these values ? [Yy/Nn] y Done. tc@box:~$ ls -la /sys/class/ata_port total 0 drwxr-xr-x 2 root root 0 Jun 27 18:21 ./ drwxr-xr-x 63 root root 0 Jun 27 18:21 ../ lrwxrwxrwx 1 root root 0 Jun 27 18:21 ata1 -> ../../devices/pci0000:00/0000:00:1f.2/ata1/ata_port/ata1 lrwxrwxrwx 1 root root 0 Jun 27 18:21 ata2 -> ../../devices/pci0000:00/0000:00:1f.2/ata2/ata_port/ata2 lrwxrwxrwx 1 root root 0 Jun 27 18:21 ata3 -> ../../devices/pci0000:00/0000:00:1f.2/ata3/ata_port/ata3 lrwxrwxrwx 1 root root 0 Jun 27 18:21 ata4 -> ../../devices/pci0000:00/0000:00:1f.2/ata4/ata_port/ata4 lrwxrwxrwx 1 root root 0 Jun 27 18:21 ata5 -> ../../devices/pci0000:00/0000:00:1f.2/ata5/ata_port/ata5 lrwxrwxrwx 1 root root 0 Jun 27 18:21 ata6 -> ../../devices/pci0000:00/0000:00:1f.2/ata6/ata_port/ata6 Думается мне что SataPortMap я не правильно выставляю, подскажите бестолковому пожалуйста. Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 27, 2022 Author Share #639 Posted June 27, 2022 28 минут назад, Razoon сказал: Думается мне что SataPortMap я не правильно выставляю, подскажите бестолковому пожалуйста. Попробуйте без sudo запустить, ругаетцо, что root не нужен: tc@box:~$ sudo ./rploader.sh satamap now Found SCSI HBAs, We need to install the SCSI modules Don't run this as root. Quote Link to comment Share on other sites More sharing options...
Razoon Posted June 28, 2022 Share #640 Posted June 28, 2022 18 часов назад, Olegin сказал: Попробуйте без sudo запустить, ругаетцо, что root не нужен: tc@box:~$ sudo ./rploader.sh satamap now Found SCSI HBAs, We need to install the SCSI modules Don't run this as root. Сделал без рута, он скачал SCSI модуль для HBA, эффект тот же, сдается мне что параметр SataPortMap отвечает за то, на какой адаптер смотрит dsm. Может еще что посоветуете? Quote Link to comment Share on other sites More sharing options...
dj_nsk Posted June 28, 2022 Share #641 Posted June 28, 2022 В 26.06.2022 в 16:36, Wodooo сказал: Кто может направить на путь истинный !?) Сейчас стоит "DSM 7.0.1-42218 Update 2" всё настроено и работает, как безболезнее обновиться до 7.1.0-42661 ? - так ведь вся эта тема подобным переходам и посвящена, просто начните с первого поста 😀 или что такое "безболезненно"? Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 28, 2022 Author Share #642 Posted June 28, 2022 11 час назад, Razoon сказал: Сделал без рута, он скачал SCSI модуль для HBA, эффект тот же, сдается мне что параметр SataPortMap отвечает за то, на какой адаптер смотрит dsm. Может еще что посоветуете? Если знаете конфигурацию sata контроллеров то прописываете в виде abn, где a-количество портов на 1м контроллере, b-на втором и т.д. Quote Link to comment Share on other sites More sharing options...
Razoon Posted June 28, 2022 Share #643 Posted June 28, 2022 11 минуту назад, Olegin сказал: Если знаете конфигурацию sata контроллеров то прописываете в виде abn, где a-количество портов на 1м контроллере, b-на втором и т.д. А можно пример строчки конфига для понимания? Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 28, 2022 Author Share #644 Posted June 28, 2022 11 минуту назад, Razoon сказал: А можно пример строчки конфига для понимания? Как-то так: SataPortMap=24 - 2 порта на 1м контроллере, 4 на 2м или SataPortMap=6 - 6 портов на 1м клнтроллере Quote Link to comment Share on other sites More sharing options...
xMiroRRside Posted June 29, 2022 Share #645 Posted June 29, 2022 Такой вопрос: Задумывался ли кто, как обновить загрузчик на работающей хрени удаленно? Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 29, 2022 Author Share #646 Posted June 29, 2022 38 минут назад, xMiroRRside сказал: Такой вопрос: Задумывался ли кто, как обновить загрузчик на работающей хрени удаленно? А чего думать? Если есть доступ по telnet/ssh - монтируете флешку в хрень и правите в конфиге grub порядок загрузки на tc... Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 29, 2022 Author Share #647 Posted June 29, 2022 (edited) UPD 29.06.2022 Если кто-то хочет побаловаться с DVA1622, который еще даже не продается, то качаем загрузчик из dev ветки, а далее все как обычно с новыми кодами, которые я добавил в список в шапке топика. Ограничения - не более 2х дисков, нет кодеков для HEVC, и видимо необходимо наличие Intel UHD Graphics 600. Из плюсов: AI раборает на GPU, т.е. видеокарта не нужна, 8 лицензий на камеры и SS выводится на подключенный к хрени монитор (пробовал HDMI и VGA). (добавил в первый топик темы). Edited June 29, 2022 by Olegin Quote Link to comment Share on other sites More sharing options...
xMiroRRside Posted June 29, 2022 Share #648 Posted June 29, 2022 13 минуты назад, Olegin сказал: правите в конфиге grub Как править и маунтить флешь - это знаем, а вот обновить удаленно tinycore-redpill c v0.4.6 до последней v0.8.0.0 Quote Link to comment Share on other sites More sharing options...
Olegin Posted June 29, 2022 Author Share #649 Posted June 29, 2022 8 минут назад, xMiroRRside сказал: Как править и маунтить флешь - это знаем, а вот обновить удаленно tinycore-redpill c v0.4.6 до последней v0.8.0.0 П.5 читаем... Quote Link to comment Share on other sites More sharing options...
kenwoodx Posted June 30, 2022 Share #650 Posted June 30, 2022 21 час назад, xMiroRRside сказал: Как править и маунтить флешь... Где почитать про это, как это делать? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.