brunokelo

terastation 7120r

Recommended Posts

568/5000

Hello, how are you?

I installed xpenology on a buffalo terastation 7120r server (http://www.buffalotech.com/products/terastation-7000-series)

but I'm not able to activate 8 of the 12 disks that are possible to install, I noticed that it has a mini-sas controller built in, which I believe to be from marvell, but even installing the additional drivers the disks are not identified, of the hardware would be USI (http://www.usish.com/english/products_NAS_2U12.php)
, has anyone used this equipment yet?


Thank you very much

Edited by brunokelo

Share this post


Link to post
Share on other sites

Not sure I understand. You say you use the Terastation 7120r server and then also provide a link to the NAS 2U12 System. So which one are you using?

Share this post


Link to post
Share on other sites

I think its made in China by USI, but re-badged to Terastation?

I'd imagine there should be a boot option to access the disk controller bios and set that up. Probably set to raid and needs to be jbod/IT/Passthrough. Found a manual, page 32 might give a pointer:)

TS-7120R-35012398-03_EN.pdf

Share this post


Link to post
Share on other sites
6 hours ago, Polanskiman said:

Not sure I understand. You say you use the Terastation 7120r server and then also provide a link to the NAS 2U12 System. So which one are you using?

 

Hello, the business model is the 7020r, however the OEM manufacturer is the USI.

Share this post


Link to post
Share on other sites
1 hour ago, sbv3000 said:

I think its made in China by USI, but re-badged to Terastation?

I'd imagine there should be a boot option to access the disk controller bios and set that up. Probably set to raid and needs to be jbod/IT/Passthrough. Found a manual, page 32 might give a pointer:)

TS-7120R-35012398-03_EN.pdf

 

In the manual raid configuration, it is done through buffalo software, which I am not using anymore, the problem is that it seems that xpenology does not have the motherboard's onboard SAS controller driver, I'm trying to find out which controller is sas this board mae owns, but I do not find any documents on the internet.

Share this post


Link to post
Share on other sites
21 hours ago, brunokelo said:

 

In the manual raid configuration, it is done through buffalo software, which I am not using anymore, the problem is that it seems that xpenology does not have the motherboard's onboard SAS controller driver, I'm trying to find out which controller is sas this board mae owns, but I do not find any documents on the internet.

 

You could try using a ubuntu live cd and check out what modules are being loaded for the sas controller. This will tell you what modules you need.

Share this post


Link to post
Share on other sites
On 12/14/2017 at 3:02 PM, Polanskiman said:

 

You could try using a ubuntu live cd and check out what modules are being loaded for the sas controller. This will tell you what modules you need.

 

 

*-storage
                description: SATA controller
                product: 88SE9125 PCIe SATA 6.0 Gb/s controller
                vendor: Marvell Technology Group Ltd.
                physical id: 0
                bus info: pci@0000:02:00.0
                version: 11
                width: 32 bits
                clock: 33MHz
                capabilities: storage pm msi pciexpress ahci_1.0 bus_master cap_list rom
                configuration: driver=ahci latency=0
                resources: irq:35 ioport:1000 ioport:1001 ioport:1002 ioport:1003 ioport:1004 memory:bfa10000-bfa107ff memory:bfa00000-bfa0ffff


 

Edited by Polanskiman
Added code tag. Please use them in the future.

Share this post


Link to post
Share on other sites

easyest way would be to install dsm one one (all) disk that work (so need to create a raid yet) and if dsm boots up you can check the log whats with the other controller(s)

as stated in the driver request, the 88SE9125 is supported as ahci in kernel 3.10.102 (used for dsm 6.1.x) and nor extra driver is needed

 

please do a "lspci -k | grep 'Kernel driver'" when started with a live linux, maybe there is more hardware and the 88SE9125 is not the one you are missing

Share this post


Link to post
Share on other sites
30 minutes ago, IG-88 said:

easyest way would be to install dsm one one (all) disk that work (so need to create a raid yet) and if dsm boots up you can check the log whats with the other controller(s)

as stated in the driver request, the 88SE9125 is supported as ahci in kernel 3.10.102 (used for dsm 6.1.x) and nor extra driver is needed

 

please do a "lspci -k | grep 'Kernel driver'" when started with a live linux, maybe there is more hardware and the 88SE9125 is not the one you are missing

 

IMG_0600.jpeg

Share this post


Link to post
Share on other sites

and, my synology,

 

image.thumb.png.02de001acdffaa6817991f16ca95210b.png

 

I believe that it is necessary to mvsas the most, funny that he is in the modules added.

 

DISK_MODULES="ehci-hcd ehci-pci BusLogic vmw_pvscsi megaraid_mm megaraid_mbox megaraid scsi_transport_spi mptbase mptscsih mptspi mptsas mptctl ata_piix megaraid_sas mpt2sas mpt3sas sx8 aacraid aic94xx 3w-9xxx 3w-sas mvsas arcmsr hptiop isci mvumi nvme"

 

image.thumb.png.902e4e7e0b5e24150a669be72ceeb51b.png

 

Edited by Polanskiman
Preferably please do no use images for code. Copy paste the code and then use tags.

Share this post


Link to post
Share on other sites

mvsas is not loaded in dsm (might be a mervell 88SE94XX)

beside checking  /var/log/dmesg for mvsas entrys you could just try to load it with insmod

 insmod /lib/modules/update/mvsas.ko

after that check with lspci -k that the module is loaded and the log

maybe there is something wrong with the module

please do a normal lspci and post the part where we can se the id's, maybe its a newer chip not supported by tha kenrnel module of kernel 3.10.102, with the id i can check the source

 

what is unusual is that there is a mvsas.ko in /lib/modules it should be in /lib/modules/update

 

 

 

Share this post


Link to post
Share on other sites

Thanks for help!!!!

 

logs  

 

insmod: ERROR: could not insert module /lib/modules/update/mvsas.ko: File exists
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.102 (root@build1) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #15217 SMP Fri Nov 10 20:08:59 CST 2017
[    0.000000] Command line: BOOT_IMAGE=/zImage syno_hdd_powerup_seq=0 HddHotplug=1 syno_hw_version=DS3615xs vender_format_version=2 console=ttyS0,115200n8 withefi elevator=elevator quiet syno_port_thaw=1 root=/dev/md0 sn=1430LWN009938 mac1=106F3F0378F4 mac2=106F3F0378F5 mac3=106F3F0378F6 mac4=106F3F0378F7 netif_num=4 vid=0x13FE pid=0x1F00
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009bfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009c000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000bcd6ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bcd70000-0x00000000bcdb8fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bcdb9000-0x00000000bcdc0fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000bcdc1000-0x00000000bcde8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000bcde9000-0x00000000bcdeafff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bcdeb000-0x00000000bcdfbfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000bcdfc000-0x00000000bce09fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bce0a000-0x00000000bce30fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000bce31000-0x00000000bce73fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bce74000-0x00000000bcffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bd800000-0x00000000bf9fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed3ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013fdfffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: USI Kiri/Kiri, BIOS Kiri 3.00 07/26/2012
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x13fe00 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-D3FFF write-protect
[    0.000000]   D4000-E7FFF uncachable
[    0.000000]   E8000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F00000000 write-back
[    0.000000]   1 base 100000000 mask FC0000000 write-back
[    0.000000]   2 base 0BD800000 mask FFF800000 uncachable
[    0.000000]   3 base 0BE000000 mask FFE000000 uncachable
[    0.000000]   4 base 0C0000000 mask FC0000000 uncachable
[    0.000000]   5 base 13FE00000 mask FFFE00000 uncachable
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000]   8 disabled
[    0.000000]   9 disabled
[    0.000000] e820: update [mem 0xbd800000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xbd000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fcd40-0x000fcd4f] mapped at [ffff8800000fcd40]
[    0.000000] Base memory trampoline at [ffff880000096000] 96000 size 24576
[    0.000000] reserving inaccessible SNB gfx pages
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01ab6000, 0x01ab6fff] PGTABLE
[    0.000000] BRK [0x01ab7000, 0x01ab7fff] PGTABLE
[    0.000000] BRK [0x01ab8000, 0x01ab8fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x13fc00000-0x13fdfffff]
[    0.000000]  [mem 0x13fc00000-0x13fdfffff] page 2M
[    0.000000] BRK [0x01ab9000, 0x01ab9fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x13c000000-0x13fbfffff]
[    0.000000]  [mem 0x13c000000-0x13fbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x13bffffff]
[    0.000000]  [mem 0x100000000-0x13bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x1fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x20200000-0x3fffffff]
[    0.000000]  [mem 0x20200000-0x3fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x40200000-0xbcd6ffff]
[    0.000000]  [mem 0x40200000-0xbcbfffff] page 2M
[    0.000000]  [mem 0xbcc00000-0xbcd6ffff] page 4k
[    0.000000] BRK [0x01aba000, 0x01abafff] PGTABLE
[    0.000000] BRK [0x01abb000, 0x01abbfff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xbcde9000-0xbcdeafff]
[    0.000000]  [mem 0xbcde9000-0xbcdeafff] page 4k
[    0.000000] init_memory_mapping: [mem 0xbce74000-0xbcffffff]
[    0.000000]  [mem 0xbce74000-0xbcffffff] page 4k
[    0.000000] RAMDISK: [mem 0x364d4000-0x37261fff]
[    0.000000] ACPI: RSDP 0x00000000000F0450 00024 (v02 ALASKA)
[    0.000000] ACPI: XSDT 0x00000000BCDB9068 00054 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.000000] ACPI: FACP 0x00000000BCDBFC90 000F4 (v04 ALASKA A M I    01072009 AMI  00010013)
[    0.000000] ACPI: DSDT 0x00000000BCDB9150 06B3E (v02 ALASKA A M I    00000300 INTL 20051117)
[    0.000000] ACPI: FACS 0x00000000BCE01F80 00040
[    0.000000] ACPI: APIC 0x00000000BCDBFD88 00072 (v03 ALASKA A M I    01072009 AMI  00010013)
[    0.000000] ACPI: SSDT 0x00000000BCDBFE00 00102 (v01 AMICPU PROC     00000001 MSFT 03000001)
[    0.000000] ACPI: MCFG 0x00000000BCDBFF08 0003C (v01 ALASKA A M I    01072009 MSFT 00000097)
[    0.000000] ACPI: HPET 0x00000000BCDBFF48 00038 (v01 ALASKA A M I    01072009 AMI. 00000004)
[    0.000000] ACPI: ASF! 0x00000000BCDBFF80 000A0 (v32 INTEL   HCG     00000001 TFSM 000F4240)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff88013b400000-ffff88013ebfffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x13fdfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009bfff]
[    0.000000]   node   0: [mem 0x00100000-0x1fffffff]
[    0.000000]   node   0: [mem 0x20200000-0x3fffffff]
[    0.000000]   node   0: [mem 0x40200000-0xbcd6ffff]
[    0.000000]   node   0: [mem 0xbcde9000-0xbcdeafff]
[    0.000000]   node   0: [mem 0xbce74000-0xbcffffff]
[    0.000000]   node   0: [mem 0x100000000-0x13fdfffff]
[    0.000000] On node 0 totalpages: 1034393
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 155 pages reserved
[    0.000000]   DMA zone: 3995 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10511 pages used for memmap
[    0.000000]   DMA32 zone: 768766 pages, LIFO batch:31
[    0.000000]   Normal zone: 3577 pages used for memmap
[    0.000000]   Normal zone: 261632 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009c000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[    0.000000] PM: Registered nosave memory: 0000000040000000 - 0000000040200000
[    0.000000] PM: Registered nosave memory: 00000000bcd70000 - 00000000bcdb9000
[    0.000000] PM: Registered nosave memory: 00000000bcdb9000 - 00000000bcdc1000
[    0.000000] PM: Registered nosave memory: 00000000bcdc1000 - 00000000bcde9000
[    0.000000] PM: Registered nosave memory: 00000000bcdeb000 - 00000000bcdfc000
[    0.000000] PM: Registered nosave memory: 00000000bcdfc000 - 00000000bce0a000
[    0.000000] PM: Registered nosave memory: 00000000bce0a000 - 00000000bce31000
[    0.000000] PM: Registered nosave memory: 00000000bce31000 - 00000000bce74000
[    0.000000] PM: Registered nosave memory: 00000000bd000000 - 00000000bd800000
[    0.000000] PM: Registered nosave memory: 00000000bd800000 - 00000000bfa00000
[    0.000000] PM: Registered nosave memory: 00000000bfa00000 - 00000000fed1c000
[    0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed40000
[    0.000000] PM: Registered nosave memory: 00000000fed40000 - 00000000ff000000
[    0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[    0.000000] e820: [mem 0xbfa00000-0xfed1bfff] available for PCI devices
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 24 pages/cpu @ffff88013fa00000 s69376 r8192 d20736 u524288
[    0.000000] pcpu-alloc: s69376 r8192 d20736 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1020094
[    0.000000] Kernel command line: BOOT_IMAGE=/zImage syno_hdd_powerup_seq=0 HddHotplug=1 syno_hw_version=DS3615xs vender_format_version=2 console=ttyS0,115200n8 withefi elevator=elevator quiet syno_port_thaw=1 root=/dev/md0 sn=1430LWN009938 mac1=106F3F0378F4 mac2=106F3F0378F5 mac3=106F3F0378F6 mac4=106F3F0378F7 netif_num=4 vid=0x13FE pid=0x1F00
[    0.000000] Power on seq num: 0
[    0.000000] Synology Hardware Version: DS3615xs-j
[    0.000000] Vender format version: 2
[    0.000000] Serial Number: 1430LWN009938
[    0.000000] Mac1: 106F3F0378F4
[    0.000000] Mac2: 106F3F0378F5
[    0.000000] Mac3: 106F3F0378F6
[    0.000000] Mac4: 106F3F0378F7
[    0.000000] Internal netif num: 4
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] Memory: 3982064k/5240832k available (4812k kernel code, 1103260k absent, 155508k reserved, 3794k data, 760k init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000]     RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] NR_IRQS:4352 nr_irqs:712 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] allocated 16777216 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.001000] tsc: Detected 3093.044 MHz processor
[    0.000001] Calibrating delay loop (skipped), value calculated using timer frequency.. 6186.08 BogoMIPS (lpj=3093044)
[    0.000003] pid_max: default: 32768 minimum: 301
[    0.000033] Security Framework initialized
[    0.000038] AppArmor: AppArmor initialized
[    0.000044] Mount-cache hash table entries: 256
[    0.000161] Initializing cgroup subsys memory
[    0.000168] Initializing cgroup subsys devices
[    0.000170] Initializing cgroup subsys freezer
[    0.000171] Initializing cgroup subsys blkio
[    0.000189] CPU: Physical Processor ID: 0
[    0.000190] CPU: Processor Core ID: 0
[    0.000193] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
               ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.000195] mce: CPU supports 9 MCE banks
[    0.000205] CPU0: Thermal monitoring enabled (TM1)
[    0.000212] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
               Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
               tlb_flushall_shift: 5
[    0.000282] Freeing SMP alternatives: 24k freed
[    0.000286] ACPI: Core revision 20130328
[    0.001817] ACPI: All ACPI Tables successfully acquired
[    0.002406] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.012407] smpboot: CPU0: Intel(R) Xeon(R) CPU E31225 @ 3.10GHz (fam: 06, model: 2a, stepping: 07)
[    0.012412] TSC deadline timer enabled
[    0.012418] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
[    0.012423] perf_event_intel: PEBS disabled due to CPU errata, please upgrade microcode
[    0.012425] ... version:                3
[    0.012426] ... bit width:              48
[    0.012426] ... generic registers:      8
[    0.012427] ... value mask:             0000ffffffffffff
[    0.012428] ... max period:             000000007fffffff
[    0.012429] ... fixed-purpose events:   3
[    0.012429] ... event mask:             00000007000000ff
[    0.012569] smpboot: Booting Node   0, Processors  #1 #2 #3 OK
[    0.052392] Brought up 4 CPUs
[    0.052395] smpboot: Total of 4 processors activated (24744.35 BogoMIPS)
[    0.054538] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.054685] devtmpfs: initialized
[    0.054857] PM: Registering ACPI NVS region [mem 0xbcd70000-0xbcdb8fff] (299008 bytes)
[    0.054862] PM: Registering ACPI NVS region [mem 0xbcdfc000-0xbce09fff] (57344 bytes)
[    0.054863] PM: Registering ACPI NVS region [mem 0xbce31000-0xbce73fff] (274432 bytes)
[    0.054936] xor: automatically using best checksumming function:
[    0.064506]    avx       : 22204.000 MB/sec
[    0.064537] NET: Registered protocol family 16
[    0.064785] ACPI: bus type PCI registered
[    0.064855] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.064857] PCI: not using MMCONFIG
[    0.064858] PCI: Using configuration type 1 for base access
[    0.067135] bio: create slab <bio-0> at 0
[    0.083519] raid6: sse2x1   gen()  8347 MB/s
[    0.100524] raid6: sse2x1   xor()  6583 MB/s
[    0.117530] raid6: sse2x2   gen() 10425 MB/s
[    0.134536] raid6: sse2x2   xor()  7488 MB/s
[    0.151544] raid6: sse2x4   gen() 11996 MB/s
[    0.168550] raid6: sse2x4   xor()  8798 MB/s
[    0.168551] raid6: using algorithm sse2x4 gen() (11996 MB/s)
[    0.168552] raid6: .... xor() 8798 MB/s, rmw enabled
[    0.168553] raid6: using ssse3x2 recovery algorithm
[    0.168568] ACPI: Added _OSI(Module Device)
[    0.168569] ACPI: Added _OSI(Processor Device)
[    0.168570] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.168571] ACPI: Added _OSI(Processor Aggregator Device)
[    0.169149] ACPI: EC: Look up EC in DSDT
[    0.169836] ACPI: Executed 1 blocks of module-level executable AML code
[    0.171326] ACPI: SSDT 0x00000000BCE00918 003E0 (v01 AMI    IST      00000001 MSFT 03000001)
[    0.171500] ACPI: Dynamic OEM Table Load:
[    0.171502] ACPI: SSDT 0x0000000000000000 003E0 (v01 AMI    IST      00000001 MSFT 03000001)
[    0.171520] ACPI: SSDT 0x00000000BCDFFD98 000E4 (v01 AMI    CST      00000001 MSFT 03000001)
[    0.171662] ACPI: Dynamic OEM Table Load:
[    0.171663] ACPI: SSDT 0x0000000000000000 000E4 (v01 AMI    CST      00000001 MSFT 03000001)
[    0.171998] ACPI: Interpreter enabled
[    0.172005] ACPI: (supports S0 S4 S5)
[    0.172006] ACPI: Using IOAPIC for interrupt routing
[    0.172020] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.172056] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.172228] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.172283] ACPI: No dock devices found.
[    0.172477] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.176391] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.176628] PCI host bridge to bus 0000:00
[    0.176630] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.176632] pci_bus 0000:00: root bus resource [io  0x0000-0x03af]
[    0.176633] pci_bus 0000:00: root bus resource [io  0x03e0-0x0cf7]
[    0.176634] pci_bus 0000:00: root bus resource [io  0x03b0-0x03df]
[    0.176635] pci_bus 0000:00: root bus resource [io  0x0d00-0xefff]
[    0.176637] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.176638] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.176639] pci_bus 0000:00: root bus resource [mem 0xbfa00000-0xffffffff]
[    0.176646] pci 0000:00:00.0: [8086:0108] type 00 class 0x060000
[    0.176713] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[    0.176737] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.176762] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.176790] pci 0000:00:01.1: [8086:0105] type 01 class 0x060400
[    0.176812] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[    0.176837] pci 0000:00:01.1: System wakeup disabled by ACPI
[    0.176868] pci 0000:00:02.0: [8086:010a] type 00 class 0x030000
[    0.176876] pci 0000:00:02.0: reg 10: [mem 0xfb400000-0xfb7fffff 64bit]
[    0.176881] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.176884] pci 0000:00:02.0: reg 20: [io  0xe000-0xe03f]
[    0.176967] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[    0.176988] pci 0000:00:16.0: reg 10: [mem 0xfbe08000-0xfbe0800f 64bit]
[    0.177059] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.177128] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[    0.177148] pci 0000:00:1a.0: reg 10: [mem 0xfbe07000-0xfbe073ff]
[    0.177232] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.177264] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.177299] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[    0.177313] pci 0000:00:1b.0: reg 10: [mem 0xfbe00000-0xfbe03fff 64bit]
[    0.177376] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.177435] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[    0.177507] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.177541] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.177579] pci 0000:00:1c.4: [8086:1c18] type 01 class 0x060400
[    0.177651] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.177685] pci 0000:00:1c.4: System wakeup disabled by ACPI
[    0.177717] pci 0000:00:1c.5: [8086:1c1a] type 01 class 0x060400
[    0.177790] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.177823] pci 0000:00:1c.5: System wakeup disabled by ACPI
[    0.177856] pci 0000:00:1c.6: [8086:1c1c] type 01 class 0x060400
[    0.177927] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[    0.177961] pci 0000:00:1c.6: System wakeup disabled by ACPI
[    0.177993] pci 0000:00:1c.7: [8086:1c1e] type 01 class 0x060400
[    0.178065] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[    0.178100] pci 0000:00:1c.7: System wakeup disabled by ACPI
[    0.178136] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[    0.178155] pci 0000:00:1d.0: reg 10: [mem 0xfbe06000-0xfbe063ff]
[    0.178239] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.178271] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.178301] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.178369] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.178401] pci 0000:00:1f.0: [8086:1c56] type 00 class 0x060100
[    0.178556] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[    0.178573] pci 0000:00:1f.2: reg 10: [io  0xe0b0-0xe0b7]
[    0.178580] pci 0000:00:1f.2: reg 14: [io  0xe0a0-0xe0a3]
[    0.178587] pci 0000:00:1f.2: reg 18: [io  0xe090-0xe097]
[    0.178594] pci 0000:00:1f.2: reg 1c: [io  0xe080-0xe083]
[    0.178601] pci 0000:00:1f.2: reg 20: [io  0xe060-0xe07f]
[    0.178609] pci 0000:00:1f.2: reg 24: [mem 0xfbe05000-0xfbe057ff]
[    0.178650] pci 0000:00:1f.2: PME# supported from D3hot
[    0.178750] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[    0.178764] pci 0000:00:1f.3: reg 10: [mem 0xfbe04000-0xfbe040ff 64bit]
[    0.178783] pci 0000:00:1f.3: reg 20: [io  0xe040-0xe05f]
[    0.178876] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.178917] pci 0000:02:00.0: [1b4b:9485] type 00 class 0x010400
[    0.178927] pci 0000:02:00.0: reg 10: [mem 0xfbd40000-0xfbd5ffff 64bit]
[    0.178934] pci 0000:02:00.0: reg 18: [mem 0xfbd00000-0xfbd3ffff 64bit]
[    0.178948] pci 0000:02:00.0: reg 30: [mem 0xfbd60000-0xfbd6ffff pref]
[    0.178971] pci 0000:02:00.0: supports D1
[    0.178972] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
[    0.181570] pci 0000:00:01.1: PCI bridge to [bus 02]
[    0.181576] pci 0000:00:01.1:   bridge window [mem 0xfbd00000-0xfbdfffff]
[    0.181686] pci 0000:03:00.0: [1b4b:9125] type 00 class 0x010601
[    0.181704] pci 0000:03:00.0: reg 10: [io  0xd040-0xd047]
[    0.181716] pci 0000:03:00.0: reg 14: [io  0xd030-0xd033]
[    0.181728] pci 0000:03:00.0: reg 18: [io  0xd020-0xd027]
[    0.181740] pci 0000:03:00.0: reg 1c: [io  0xd010-0xd013]
[    0.181752] pci 0000:03:00.0: reg 20: [io  0xd000-0xd00f]
[    0.181765] pci 0000:03:00.0: reg 24: [mem 0xfbc10000-0xfbc107ff]
[    0.181777] pci 0000:03:00.0: reg 30: [mem 0xfbc00000-0xfbc0ffff pref]
[    0.181833] pci 0000:03:00.0: PME# supported from D3hot
[    0.184572] pci 0000:00:1c.0: PCI bridge to [bus 03]
[    0.184579] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.184584] pci 0000:00:1c.0:   bridge window [mem 0xfbc00000-0xfbcfffff]
[    0.184704] pci 0000:04:00.0: [8086:10d3] type 00 class 0x020000
[    0.184736] pci 0000:04:00.0: reg 10: [mem 0xfbb00000-0xfbb1ffff]
[    0.184779] pci 0000:04:00.0: reg 18: [io  0xc000-0xc01f]
[    0.184801] pci 0000:04:00.0: reg 1c: [mem 0xfbb20000-0xfbb23fff]
[    0.184988] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[    0.187579] pci 0000:00:1c.4: PCI bridge to [bus 04]
[    0.187585] pci 0000:00:1c.4:   bridge window [io  0xc000-0xcfff]
[    0.187591] pci 0000:00:1c.4:   bridge window [mem 0xfbb00000-0xfbbfffff]
[    0.187706] pci 0000:05:00.0: [8086:10d3] type 00 class 0x020000
[    0.187738] pci 0000:05:00.0: reg 10: [mem 0xfba00000-0xfba1ffff]
[    0.187781] pci 0000:05:00.0: reg 18: [io  0xb000-0xb01f]
[    0.187803] pci 0000:05:00.0: reg 1c: [mem 0xfba20000-0xfba23fff]
[    0.187988] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[    0.190583] pci 0000:00:1c.5: PCI bridge to [bus 05]
[    0.190589] pci 0000:00:1c.5:   bridge window [io  0xb000-0xbfff]
[    0.190594] pci 0000:00:1c.5:   bridge window [mem 0xfba00000-0xfbafffff]
[    0.190710] pci 0000:06:00.0: [8086:10d3] type 00 class 0x020000
[    0.190741] pci 0000:06:00.0: reg 10: [mem 0xfb900000-0xfb91ffff]
[    0.190784] pci 0000:06:00.0: reg 18: [io  0xa000-0xa01f]
[    0.190806] pci 0000:06:00.0: reg 1c: [mem 0xfb920000-0xfb923fff]
[    0.190991] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[    0.193587] pci 0000:00:1c.6: PCI bridge to [bus 06]
[    0.193592] pci 0000:00:1c.6:   bridge window [io  0xa000-0xafff]
[    0.193598] pci 0000:00:1c.6:   bridge window [mem 0xfb900000-0xfb9fffff]
[    0.193714] pci 0000:07:00.0: [8086:10d3] type 00 class 0x020000
[    0.193745] pci 0000:07:00.0: reg 10: [mem 0xfb800000-0xfb81ffff]
[    0.193788] pci 0000:07:00.0: reg 18: [io  0x9000-0x901f]
[    0.193810] pci 0000:07:00.0: reg 1c: [mem 0xfb820000-0xfb823fff]
[    0.193995] pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
[    0.196590] pci 0000:00:1c.7: PCI bridge to [bus 07]
[    0.196595] pci 0000:00:1c.7:   bridge window [io  0x9000-0x9fff]
[    0.196600] pci 0000:00:1c.7:   bridge window [mem 0xfb800000-0xfb8fffff]
[    0.196695] pci 0000:00:1e.0: PCI bridge to [bus 08] (subtractive decode)
[    0.196704] pci 0000:00:1e.0:   bridge window [io  0x0000-0x03af] (subtractive decode)
[    0.196705] pci 0000:00:1e.0:   bridge window [io  0x03e0-0x0cf7] (subtractive decode)
[    0.196706] pci 0000:00:1e.0:   bridge window [io  0x03b0-0x03df] (subtractive decode)
[    0.196707] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xefff] (subtractive decode)
[    0.196709] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.196710] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.196711] pci 0000:00:1e.0:   bridge window [mem 0xbfa00000-0xffffffff] (subtractive decode)
[    0.196740] pci_bus 0000:00: on NUMA node 0
[    0.196801] acpi PNP0A08:00: Requesting ACPI _OSC control (0x1d)
[    0.196886] acpi PNP0A08:00: ACPI _OSC control (0x1d) granted
[    0.197122] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.197158] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.197193] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12 14 15)
[    0.197227] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.197262] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
[    0.197296] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
[    0.197330] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.197365] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.197434] ACPI: Enabled 3 GPEs in block 00 to 3F
[    0.197438] acpi root: \_SB_.PCI0 notify handler is installed
[    0.197462] Found 1 acpi root devices
[    0.197550] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.197552] vgaarb: loaded
[    0.197553] vgaarb: bridge control possible 0000:00:02.0
[    0.197639] SCSI subsystem initialized
[    0.197641] ACPI: bus type ATA registered
[    0.197702] libata version 3.00 loaded.
[    0.197761] pps_core: LinuxPPS API ver. 1 registered
[    0.197762] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.197775] PTP clock support registered
[    0.197825] PCI: Using ACPI for IRQ routing
[    0.203660] PCI: pci_cache_line_size set to 64 bytes
[    0.203726] e820: reserve RAM buffer [mem 0x0009c000-0x0009ffff]
[    0.203727] e820: reserve RAM buffer [mem 0xbcd70000-0xbfffffff]
[    0.203729] e820: reserve RAM buffer [mem 0xbcdeb000-0xbfffffff]
[    0.203730] e820: reserve RAM buffer [mem 0xbd000000-0xbfffffff]
[    0.203731] e820: reserve RAM buffer [mem 0x13fe00000-0x13fffffff]
[    0.203872] Switching to clocksource hpet
[    0.203928] AppArmor: AppArmor Filesystem Enabled
[    0.203954] pnp: PnP ACPI init
[    0.203958] ACPI: bus type PNP registered
[    0.204044] system 00:00: [mem 0xfed10000-0xfed19fff] has been reserved
[    0.204046] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[    0.204047] system 00:00: [mem 0xfed90000-0xfed93fff] has been reserved
[    0.204049] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.204050] system 00:00: [mem 0xfee00000-0xfee0ffff] has been reserved
[    0.204052] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.204164] system 00:01: [io  0x0a00-0x0a1f] has been reserved
[    0.204166] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.204215] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.204263] pnp 00:03: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    0.204377] pnp 00:04: [dma 0 disabled]
[    0.204426] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.204433] pnp 00:05: [dma 4]
[    0.204459] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.204492] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.204522] pnp 00:07: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.204571] system 00:08: [io  0x04d0-0x04d1] has been reserved
[    0.204584] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.204629] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.204777] system 00:0a: [io  0x0400-0x0453] could not be reserved
[    0.204779] system 00:0a: [io  0x0458-0x047f] has been reserved
[    0.204780] system 00:0a: [io  0xf040-0xf05f] has been reserved
[    0.204782] system 00:0a: [io  0x0500-0x057f] has been reserved
[    0.204784] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.204785] system 00:0a: [mem 0xfec00000-0xfecfffff] could not be reserved
[    0.204787] system 00:0a: [mem 0xfed08000-0xfed08fff] has been reserved
[    0.204788] system 00:0a: [mem 0xff000000-0xffffffff] has been reserved
[    0.204789] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.204850] system 00:0b: [io  0x0454-0x0457] has been reserved
[    0.204851] system 00:0b: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.204950] pnp 00:0c: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.205041] pnp: PnP ACPI: found 13 devices
[    0.205041] ACPI: bus type PNP unregistered
[    0.213072] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.213077] pci 0000:00:01.1: PCI bridge to [bus 02]
[    0.213079] pci 0000:00:01.1:   bridge window [mem 0xfbd00000-0xfbdfffff]
[    0.213082] pci 0000:00:1c.0: PCI bridge to [bus 03]
[    0.213085] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.213090] pci 0000:00:1c.0:   bridge window [mem 0xfbc00000-0xfbcfffff]
[    0.213097] pci 0000:00:1c.4: PCI bridge to [bus 04]
[    0.213100] pci 0000:00:1c.4:   bridge window [io  0xc000-0xcfff]
[    0.213105] pci 0000:00:1c.4:   bridge window [mem 0xfbb00000-0xfbbfffff]
[    0.213112] pci 0000:00:1c.5: PCI bridge to [bus 05]
[    0.213115] pci 0000:00:1c.5:   bridge window [io  0xb000-0xbfff]
[    0.213120] pci 0000:00:1c.5:   bridge window [mem 0xfba00000-0xfbafffff]
[    0.213127] pci 0000:00:1c.6: PCI bridge to [bus 06]
[    0.213130] pci 0000:00:1c.6:   bridge window [io  0xa000-0xafff]
[    0.213134] pci 0000:00:1c.6:   bridge window [mem 0xfb900000-0xfb9fffff]
[    0.213142] pci 0000:00:1c.7: PCI bridge to [bus 07]
[    0.213144] pci 0000:00:1c.7:   bridge window [io  0x9000-0x9fff]
[    0.213149] pci 0000:00:1c.7:   bridge window [mem 0xfb800000-0xfb8fffff]
[    0.213156] pci 0000:00:1e.0: PCI bridge to [bus 08]
[    0.213403] pci 0000:00:1e.0: setting latency timer to 64
[    0.213407] pci_bus 0000:00: resource 4 [io  0x0000-0x03af]
[    0.213408] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7]
[    0.213409] pci_bus 0000:00: resource 6 [io  0x03b0-0x03df]
[    0.213411] pci_bus 0000:00: resource 7 [io  0x0d00-0xefff]
[    0.213412] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[    0.213413] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
[    0.213414] pci_bus 0000:00: resource 10 [mem 0xbfa00000-0xffffffff]
[    0.213416] pci_bus 0000:02: resource 1 [mem 0xfbd00000-0xfbdfffff]
[    0.213417] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    0.213418] pci_bus 0000:03: resource 1 [mem 0xfbc00000-0xfbcfffff]
[    0.213419] pci_bus 0000:04: resource 0 [io  0xc000-0xcfff]
[    0.213421] pci_bus 0000:04: resource 1 [mem 0xfbb00000-0xfbbfffff]
[    0.213422] pci_bus 0000:05: resource 0 [io  0xb000-0xbfff]
[    0.213423] pci_bus 0000:05: resource 1 [mem 0xfba00000-0xfbafffff]
[    0.213424] pci_bus 0000:06: resource 0 [io  0xa000-0xafff]
[    0.213425] pci_bus 0000:06: resource 1 [mem 0xfb900000-0xfb9fffff]
[    0.213426] pci_bus 0000:07: resource 0 [io  0x9000-0x9fff]
[    0.213428] pci_bus 0000:07: resource 1 [mem 0xfb800000-0xfb8fffff]
[    0.213429] pci_bus 0000:08: resource 4 [io  0x0000-0x03af]
[    0.213430] pci_bus 0000:08: resource 5 [io  0x03e0-0x0cf7]
[    0.213431] pci_bus 0000:08: resource 6 [io  0x03b0-0x03df]
[    0.213432] pci_bus 0000:08: resource 7 [io  0x0d00-0xefff]
[    0.213434] pci_bus 0000:08: resource 8 [mem 0x000a0000-0x000bffff]
[    0.213435] pci_bus 0000:08: resource 9 [mem 0x000c0000-0x000dffff]
[    0.213436] pci_bus 0000:08: resource 10 [mem 0xbfa00000-0xffffffff]
[    0.213477] NET: Registered protocol family 2
[    0.213610] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    0.213666] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.213721] TCP: Hash tables configured (established 32768 bind 32768)
[    0.213733] TCP: reno registered
[    0.213736] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.213745] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.213789] NET: Registered protocol family 1
[    0.213871] RPC: Registered named UNIX socket transport module.
[    0.213872] RPC: Registered udp transport module.
[    0.213873] RPC: Registered tcp transport module.
[    0.213874] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.213894] pci 0000:00:02.0: BIOS left Intel GPU interrupts enabled; disabling
[    0.213904] pci 0000:00:02.0: Boot video device
[    0.455930] PCI: CLS 64 bytes, default 64
[    0.455955] Trying to unpack rootfs image as initramfs...
[    2.656719] Freeing initrd memory: 13880k freed
[    2.667518] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    2.667522] software IO TLB [mem 0xb8d70000-0xbcd70000] (64MB) mapped at [ffff8800b8d70000-ffff8800bcd6ffff]
[    2.673107] audit: initializing netlink socket (disabled)
[    2.673117] type=2000 audit(1513290729.668:1): initialized
[    2.677378] bounce pool size: 64 pages
[    2.677816] VFS: Disk quotas dquot_6.5.2
[    2.677832] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    2.678386] NFS: Registering the id_resolver key type
[    2.678393] Key type id_resolver registered
[    2.678394] Key type id_legacy registered
[    2.678402] msgmni has been set to 7804
[    2.678738] async_tx: api initialized (async)
[    2.678810] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    2.678811] io scheduler noop registered
[    2.678812] io scheduler deadline registered
[    2.678818] io scheduler cfq registered (default)
[    2.679027] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    2.679323] pcieport 0000:00:01.1: irq 41 for MSI/MSI-X
[    2.679867] pcieport 0000:00:1c.0: irq 42 for MSI/MSI-X
[    2.680178] pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X
[    2.680564] pcieport 0000:00:1c.5: irq 44 for MSI/MSI-X
[    2.680788] pcieport 0000:00:1c.6: irq 45 for MSI/MSI-X
[    2.681971] pcieport 0000:00:1c.7: irq 46 for MSI/MSI-X
[    2.927193] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.948111] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.948219] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 8250
[    2.973803] brd: module loaded
[    2.978012] Loading iSCSI transport class v2.0-870.
[    2.987778] rdac: device handler registered
[    2.989487] ahci 0000:00:1f.2: version 3.0
[    2.989586] ahci 0000:00:1f.2: irq 47 for MSI/MSI-X
[    3.000309] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[    3.000316] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst 
[    3.000323] ahci 0000:00:1f.2: setting latency timer to 64
[    3.017410] scsi0 : ahci
[    3.019332] scsi1 : ahci
[    3.019728] scsi2 : ahci
[    3.020106] scsi3 : ahci
[    3.020889] scsi4 : ahci
[    3.023035] scsi5 : ahci
[    3.023393] ata1: SATA max UDMA/133 abar m2048@0xfbe05000 port 0xfbe05100 irq 47
[    3.023397] ata2: SATA max UDMA/133 abar m2048@0xfbe05000 port 0xfbe05180 irq 47
[    3.023399] ata3: SATA max UDMA/133 abar m2048@0xfbe05000 port 0xfbe05200 irq 47
[    3.023402] ata4: SATA max UDMA/133 abar m2048@0xfbe05000 port 0xfbe05280 irq 47
[    3.023404] ata5: SATA max UDMA/133 abar m2048@0xfbe05000 port 0xfbe05300 irq 47
[    3.023407] ata6: SATA max UDMA/133 abar m2048@0xfbe05000 port 0xfbe05380 irq 47
[    3.023495] ahci 0000:03:00.0: irq 48 for MSI/MSI-X
[    3.023553] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    3.023556] ahci 0000:03:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs 
[    3.023562] ahci 0000:03:00.0: port 0 can do FBS, forcing FBSCP
[    3.023589] ahci 0000:03:00.0: port 1 can do FBS, forcing FBSCP
[    3.026080] scsi6 : ahci
[    3.026610] scsi7 : ahci
[    3.027770] ata7: SATA max UDMA/133 abar m2048@0xfbc10000 port 0xfbc10100 irq 48
[    3.027774] ata8: SATA max UDMA/133 abar m2048@0xfbc10000 port 0xfbc10180 irq 48
[    3.031513] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    3.032603] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.032608] serio: i8042 AUX port at 0x60,0x64 irq 12
[    3.032995] rtc_cmos 00:06: RTC can wake from S4
[    3.033584] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    3.033612] rtc_cmos 00:06: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    3.034318] i2c /dev entries driver
[    3.035994] it87: Found IT8721F chip at 0xa00, revision 3
[    3.038078] md: linear personality registered for level -1
[    3.038081] md: raid0 personality registered for level 0
[    3.038082] md: raid1 personality registered for level 1
[    3.038083] md: raid10 personality registered for level 10
[    3.038966] md: raid6 personality registered for level 6
[    3.038968] md: raid5 personality registered for level 5
[    3.038968] md: raid4 personality registered for level 4
[    3.038969] md: raidF1 personality registered for level 45
[    3.039191] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[    3.039193] cpuidle: using governor ladder
[    3.039194] cpuidle: using governor menu
[    3.039251] TCP: cubic registered
[    3.039279] NET: Registered protocol family 17
[    3.039298] Key type dns_resolver registered
[    3.328221] ata4: SATA link down (SStatus 0 SControl 300)
[    3.328247] ata5: SATA link down (SStatus 0 SControl 300)
[    3.328278] ata6: SATA link down (SStatus 0 SControl 300)
[    3.328298] ata3: SATA link down (SStatus 0 SControl 300)
[    3.330211] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.330233] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.331002] ata2.00: ATA-9: ST4000DM000-1F2168, CC54, max UDMA/133
[    3.331010] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.331019] ata1.00: ATA-9: ST4000DM000-1F2168, CC54, max UDMA/133
[    3.331022] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.331855] ata2.00: configured for UDMA/133
[    3.331877] ata1.00: configured for UDMA/133
[    3.360735] scsi 0:0:0:0: Direct-Access     ATA      ST4000DM000-1F2168       CC54 PQ: 0 ANSI: 5
[    3.360999] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    3.361001] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    3.361036] sd 0:0:0:0: [sda] Write Protect is off
[    3.361038] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.361053] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.361723] scsi 1:0:0:0: Direct-Access     ATA      ST4000DM000-1F2168       CC54 PQ: 0 ANSI: 5
[    3.362909] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    3.362911] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    3.362947] sd 1:0:0:0: [sdb] Write Protect is off
[    3.362949] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    3.362964] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.420943]  sda: sda1 sda2 sda3
[    3.421352] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.427507]  sdb: sdb1 sdb2 sdb3
[    3.427936] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.487185] ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
[    3.487214] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
[    3.488593] ata7.00: ATA-10: ST4000DM000-2AE166, 0001, max UDMA/133
[    3.488597] ata7.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    3.489687] ata7.00: configured for UDMA/133
[    3.490597] scsi 6:0:0:0: Direct-Access     ATA      ST4000DM000-2AE166       0001 PQ: 0 ANSI: 5
[    3.490855] sd 6:0:0:0: [sdg] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[    3.490857] sd 6:0:0:0: [sdg] 4096-byte physical blocks
[    3.490892] sd 6:0:0:0: [sdg] Write Protect is off
[    3.490893] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[    3.490909] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.499152] ata8.00: ATA-8: OCZ-VERTEX3, 2.15, max UDMA/133
[    3.499167] ata8.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.524350] ata8.00: configured for UDMA/133
[    3.524366] ata8.00: Find SSD disks. [OCZ-VERTEX3]
[    3.528248] scsi 7:0:0:0: Direct-Access     OCZ      VERTEX3                  2.15 PQ: 0 ANSI: 5
[    3.528489] sd 7:0:0:0: [sdh] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
[    3.528537] sd 7:0:0:0: [sdh] Write Protect is off
[    3.528539] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[    3.528554] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.528929]  sdh: sdh1
[    3.529719] sd 7:0:0:0: [sdh] Attached SCSI disk
[    3.670135] tsc: Refined TSC clocksource calibration: 3092.972 MHz
[    3.670141] Switching to clocksource tsc
[    3.742002]  sdg: sdg1 sdg2 sdg3
[    3.742312] sd 6:0:0:0: [sdg] Attached SCSI disk
[    3.742330] registered taskstats version 1
[    3.743050] rtc_cmos 00:06: setting system clock to 2017-12-14 22:32:11 UTC (1513290731)
[    3.743483] Freeing unused kernel memory: 760k freed
[    3.743538] Write protecting the kernel read-only data: 8192k
[    3.743626] Freeing unused kernel memory: 1320k freed
[    3.744370] Freeing unused kernel memory: 500k freed
[    3.777721] ACPI: bus type USB registered
[    3.777806] usbcore: registered new interface driver usbfs
[    3.777842] usbcore: registered new interface driver hub
[    3.778428] usbcore: registered new interface driver ethub
[    3.778781] usbcore: registered new device driver usb
[    3.785148] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.787774] ehci-pci: EHCI PCI platform driver
[    3.787858] ehci-pci 0000:00:1a.0: setting latency timer to 64
[    3.787867] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    3.787871] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    3.787883] ehci-pci 0000:00:1a.0: debug port 2
[    3.791779] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    3.791795] ehci-pci 0000:00:1a.0: irq 16, io mem 0xfbe07000
[    3.797102] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    3.797285] hub 1-0:1.0: USB hub found
[    3.797290] hub 1-0:1.0: 2 ports detected
[    3.797387] ehci-pci 0000:00:1d.0: setting latency timer to 64
[    3.797392] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    3.797396] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    3.797406] ehci-pci 0000:00:1d.0: debug port 2
[    3.801300] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    3.801315] ehci-pci 0000:00:1d.0: irq 23, io mem 0xfbe06000
[    3.807096] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    3.807267] hub 2-0:1.0: USB hub found
[    3.807271] hub 2-0:1.0: 2 ports detected
[    3.810789] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.814382] uhci_hcd: USB Universal Host Controller Interface driver
[    3.827698] usbcore: registered new interface driver usb-storage
[    3.837656] VMware PVSCSI driver - version 1.0.2.0-k
[    3.840369] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    3.843111] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    3.851416] Fusion MPT base driver 3.04.20
[    3.851419] Copyright (c) 1999-2008 LSI Corporation
[    3.856709] Fusion MPT SPI Host driver 3.04.20
[    3.859480] Fusion MPT SAS Host driver 3.04.20
[    3.862167] Fusion MPT misc device (ioctl) driver 3.04.20
[    3.862254] mptctl: Registered with Fusion MPT base driver
[    3.862256] mptctl: /dev/mptctl @ (major,minor=10,220)
[    3.867711] megasas: 06.506.00.00-rc1 Sat. Feb. 9 17:00:00 PDT 2013
[    3.870785] mpt2sas version 20.00.00.00 loaded
[    3.873776] mpt3sas version 01.100.01.00 loaded
[    3.879426] Adaptec aacraid driver 1.2-0[30200]-ms
[    3.882289] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[    3.885027] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[    3.887797] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000.
[    3.896076] RocketRAID 3xxx/4xxx Controller driver v1.8
[    3.898929] isci: Intel(R) C600 SAS Controller Driver - version 1.1.0
[    3.909501] bromolow_synobios: module license 'Synology Inc.' taints kernel.
[    3.909504] Disabling lock debugging due to kernel taint
[    3.909744] 2017-12-14 22:32:11 UTC
[    3.909746] synobios: load, major number 201
[    3.909748] Brand: Synology
[    3.909749] Model: DS-3615xs
[    3.909751] set group disks wakeup number to 4, spinup time deno 7
[    4.120029] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    4.255354] Got empty serial number. Generate serial number from product.
[    4.255649] hub 1-1:1.0: USB hub found
[    4.255725] hub 1-1:1.0: 6 ports detected
[    4.378971] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    4.409968] synobios cpu_arch proc entry initialized
[    4.409973] synobios crypto_hw proc entry initialized
[    4.409975] synobios syno_platform proc entry initialized
[    4.415155] synobios: unload
[    4.420254] md: Autodetecting RAID arrays.
[    4.469690] md: invalid raid superblock magic on sda3
[    4.474809] md: sda3 does not have a valid v0.90 superblock, not importing!
[    4.514295] Got empty serial number. Generate serial number from product.
[    4.514302] drivers/usb/core/hub.c (2679) Same device found. Change serial to ffffffd1ffffffb2ffffffdbffffffa0 
[    4.514593] hub 2-1:1.0: USB hub found
[    4.514667] hub 2-1:1.0: 8 ports detected
[    4.530080] md: invalid raid superblock magic on sdb3
[    4.535163] md: sdb3 does not have a valid v0.90 superblock, not importing!
[    4.599028] usb 1-1.2: new high-speed USB device number 3 using ehci-pci
[    4.607415] md: invalid raid superblock magic on sdg3
[    4.612526] md: sdg3 does not have a valid v0.90 superblock, not importing!
[    4.614233] md: invalid raid superblock magic on sdh1
[    4.619302] md: sdh1 does not have a valid v0.90 superblock, not importing!
[    4.619305] md: Scanned 10 and added 6 devices.
[    4.619306] md: autorun ...
[    4.619307] md: considering sda1 ...
[    4.619309] md:  adding sda1 ...
[    4.619311] md: sda2 has different UUID to sda1
[    4.619313] md:  adding sdb1 ...
[    4.619314] md: sdb2 has different UUID to sda1
[    4.619316] md:  adding sdg1 ...
[    4.619317] md: sdg2 has different UUID to sda1
[    4.619321] md: created md0
[    4.619323] md: bind<sdg1>
[    4.619331] md: bind<sdb1>
[    4.619335] md: bind<sda1>
[    4.619340] md: running: <sda1><sdb1><sdg1>
[    4.619435] md/raid1:md0: active with 3 out of 12 mirrors
[    4.619448] md0: detected capacity change from 0 to 2549940224
[    4.619491] md: considering sda2 ...
[    4.619495] md:  adding sda2 ...
[    4.619497] md:  adding sdb2 ...
[    4.619498] md:  adding sdg2 ...
[    4.619631] md: created md1
[    4.619632] md: bind<sdg2>
[    4.619636] md: bind<sdb2>
[    4.619644] md: bind<sda2>
[    4.619649] md: running: <sda2><sdb2><sdg2>
[    4.619732] md/raid1:md1: active with 3 out of 12 mirrors
[    4.619740] md1: detected capacity change from 0 to 2147418112
[    4.619850] md: ... autorun DONE.
[    4.653800]  md0: unknown partition table
[    4.704303] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    4.704336] scsi8 : usb-storage 1-1.2:1.0
[    4.802985] usb 2-1.3: new low-speed USB device number 3 using ehci-pci
[    4.901956] Got empty serial number. Generate serial number from product.
[    4.987943] usb 2-1.6: new low-speed USB device number 4 using ehci-pci
[    5.090661] Got empty serial number. Generate serial number from product.
[    5.256521] EXT4-fs (md0): barriers disabled
[    5.268331] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: 
[    5.707533] scsi 8:0:0:0: Direct-Access     Kingston DataTraveler 2.0         PMAP PQ: 0 ANSI: 0 CCS
[    5.708280] sd 8:0:0:0: [synoboot] 7823360 512-byte logical blocks: (4.00 GB/3.73 GiB)
[    5.708904] sd 8:0:0:0: [synoboot] Write Protect is off
[    5.708907] sd 8:0:0:0: [synoboot] Mode Sense: 23 00 00 00
[    5.709699] sd 8:0:0:0: [synoboot] No Caching mode page found
[    5.715478] sd 8:0:0:0: [synoboot] Assuming drive cache: write through
[    5.724903] sd 8:0:0:0: [synoboot] No Caching mode page found
[    5.730663] sd 8:0:0:0: [synoboot] Assuming drive cache: write through
[    5.745808]  synoboot: synoboot1 synoboot2 synoboot3
[    5.748143] sd 8:0:0:0: [synoboot] No Caching mode page found
[    5.753903] sd 8:0:0:0: [synoboot] Assuming drive cache: write through
[    5.760461] sd 8:0:0:0: [synoboot] Attached SCSI removable disk
[    9.468468] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: barrier=1
[   11.171786] EXT4-fs (md0): re-mounted. Opts: (null)
[   14.623059] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   14.623094] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   14.623124] sd 6:0:0:0: Attached scsi generic sg2 type 0
[   14.623154] sd 7:0:0:0: Attached scsi generic sg3 type 0
[   14.623184] sd 8:0:0:0: Attached scsi generic sg4 type 0
[   14.926455]  md1: unknown partition table
[   15.083802] Adding 2097084k swap on /dev/md1.  Priority:-1 extents:1 across:2097084k 
[   15.378177] zram: module is from the staging directory, the quality is unknown, you have been warned.
[   15.378630] zram: Created 4 device(s) ...
[   15.388232] Adding 600060k swap on /dev/zram0.  Priority:1 extents:1 across:600060k SS
[   15.393370] Adding 600060k swap on /dev/zram1.  Priority:1 extents:1 across:600060k SS
[   15.398435] Adding 600060k swap on /dev/zram2.  Priority:1 extents:1 across:600060k SS
[   15.403567] Adding 600060k swap on /dev/zram3.  Priority:1 extents:1 across:600060k SS
[   16.829349] NET: Registered protocol family 10
[   16.853824] sit: IPv6 over IPv4 tunneling driver
[   16.958296] init: syno-auth-check main process (5562) killed by TERM signal
[   17.108628] ACPI: Requesting acpi_cpufreq
[   17.108739] Monitor-Mwait will be used to enter C-1 state
[   17.108746] Monitor-Mwait will be used to enter C-3 state
[   17.108758] ACPI: acpi_idle registered with cpuidle
[   17.540494] fuse init (API version 7.22)
[   17.542894] dca service started, version 1.12.1
[   17.545233] e1000e: Intel(R) PRO/1000 Network Driver - 3.3.4-NAPI
[   17.545235] e1000e: Copyright(c) 1999 - 2016 Intel Corporation.
[   17.545420] e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[   17.545457] e1000e 0000:04:00.0: irq 49 for MSI/MSI-X
[   17.649654] e1000e 0000:04:00.0 eth0: registered PHC clock
[   17.649658] e1000e 0000:04:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 10:6f:3f:03:78:f4
[   17.649659] e1000e 0000:04:00.0 eth0: Intel(R) PRO/1000 Network Connection
[   17.649744] e1000e 0000:04:00.0 eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[   17.649905] e1000e 0000:05:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[   17.649941] e1000e 0000:05:00.0: irq 50 for MSI/MSI-X
[   17.754658] e1000e 0000:05:00.0 eth1: registered PHC clock
[   17.754661] e1000e 0000:05:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 10:6f:3f:03:78:f5
[   17.754663] e1000e 0000:05:00.0 eth1: Intel(R) PRO/1000 Network Connection
[   17.754747] e1000e 0000:05:00.0 eth1: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[   17.754902] e1000e 0000:06:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[   17.754937] e1000e 0000:06:00.0: irq 51 for MSI/MSI-X
[   17.864880] e1000e 0000:06:00.0 eth2: registered PHC clock
[   17.864884] e1000e 0000:06:00.0 eth2: (PCI Express:2.5GT/s:Width x1) 10:6f:3f:03:78:f6
[   17.864885] e1000e 0000:06:00.0 eth2: Intel(R) PRO/1000 Network Connection
[   17.864970] e1000e 0000:06:00.0 eth2: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[   17.865153] e1000e 0000:07:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[   17.865191] e1000e 0000:07:00.0: irq 52 for MSI/MSI-X
[   17.975036] e1000e 0000:07:00.0 eth3: registered PHC clock
[   17.975040] e1000e 0000:07:00.0 eth3: (PCI Express:2.5GT/s:Width x1) 10:6f:3f:03:78:f7
[   17.975042] e1000e 0000:07:00.0 eth3: Intel(R) PRO/1000 Network Connection
[   17.975126] e1000e 0000:07:00.0 eth3: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[   18.070577] Intel(R) Gigabit Ethernet Network Driver - version 5.3.5.3
[   18.070580] Copyright (c) 2007-2015 Intel Corporation.
[   18.075631] Intel(R) 10GbE PCI Express Linux Network Driver - version 5.3.3
[   18.075643] Copyright(c) 1999 - 2017 Intel Corporation.
[   18.078179] i40e: Intel(R) 40-10 Gigabit Ethernet Connection Network Driver - version 1.5.19
[   18.078181] i40e: Copyright(c) 2013 - 2016 Intel Corporation.
[   18.080747] tn40xx low_mem_msg proc entry initialized
[   18.080750] tn40xx low_mem_counter proc entry initialized
[   18.080751] tn40xx debug_msg proc entry initialized
[   18.080752] tn40xx: Tehuti Network Driver, 0.3.6.12.3
[   18.085358] Loading modules backported from Linux version v3.18.1-0-g39ca484
[   18.085360] Backport generated by backports.git v3.18.1-1-0-g5e9ec4c
[   18.088032] Compat-mlnx-ofed backport release: cd30181
[   18.088034] Backport based on mlnx_ofed/mlnx_rdma.git cd30181
[   18.088035] compat.git: mlnx_ofed/mlnx_rdma.git
[   18.109984] bnx2x: QLogic 5771x/578xx 10/20-Gigabit Ethernet Driver bnx2x 1.713.00 ($DateTime: 2015/07/28 00:13:30 $)
[   18.339261] bio: create slab <bio-1> at 1
[   18.339341] Btrfs loaded
[   18.428465] exFAT: Version 1.2.9
[   18.451375] jme: JMicron JMC2XX ethernet driver version 1.0.8
[   18.455609] sky2: driver version 1.30
[   18.460305] pch_gbe: EG20T PCH Gigabit Ethernet Driver - version 1.01
[   18.464769] QLogic 1/10 GbE Converged/Intelligent Ethernet Driver v5.2.42
[   18.469195] QLogic/NetXen Network Driver v4.0.80
[   18.471652] Solarflare NET driver v3.2
[   18.473840] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[   18.473844] e1000: Copyright (c) 1999-2006 Intel Corporation.
[   18.475912] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[   18.477977] VMware vmxnet3 virtual NIC driver - version 1.1.30.0-k-NAPI
[   18.484582] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.16 (Dec 05, 2012)
[   18.498696] usbcore: registered new interface driver ax88179_178a
[   18.500820] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[   18.500824] ACPI: Power Button [PWRB]
[   18.500922] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[   18.500926] ACPI: Power Button [PWRF]
[   18.506547] Atheros(R) L2 Ethernet Driver - version 2.2.3
[   18.506550] Copyright (c) 2007 Atheros Corporation.
[   18.508776] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[   18.508778] e100: Copyright(c) 1999-2006 Intel Corporation
[   18.510884] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k
[   18.510886] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[   18.512988] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[   18.512990] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[   18.515250] ixgbevf: Intel(R) 10GbE PCI Express Virtual Function Driver - version 4.3.2
[   18.515251] Copyright(c) 1999 - 2017 Intel Corporation.
[   18.521809] usbcore: registered new interface driver rtl8150
[   18.523992] usbcore: registered new interface driver r8152
[   18.526090] usbcore: registered new interface driver cx82310_eth
[   18.528278] usbcore: registered new interface driver asix
[   18.530472] usbcore: registered new interface driver plusb
[   18.535044] et131x: module is from the staging directory, the quality is unknown, you have been warned.
[   18.578793] 2017-12-14 22:32:26 UTC
[   18.578797] synobios: load, major number 201
[   18.578799] Brand: Synology
[   18.578801] Model: DS-3615xs
[   18.578802] set group disks wakeup number to 4, spinup time deno 7
[   18.993967] systemd-udevd[6390]: starting version 204
[   19.078733] synobios cpu_arch proc entry initialized
[   19.078738] synobios crypto_hw proc entry initialized
[   19.078739] synobios syno_platform proc entry initialized
[   19.645601] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   19.646361] bonding: bond0 is being deleted...
[   19.646463] bonding: bond0: released all slaves
[   19.659149] bonding: bond0 is being created...
[   19.660429] bonding: bond0: setting mode to balance-alb (6).
[   19.660466] bonding: bond0: Setting use_carrier to 1.
[   19.660499] bonding: bond0: Setting MII monitoring interval to 100.
[   19.660528] bonding: bond0: Setting up delay to 100.
[   19.660939] IPv6: ADDRCONF(NETDEV_UP): bond0: link is not ready
[   19.663735] bonding: bond0: Adding slave eth0.
[   19.739598] e1000e 0000:04:00.0: irq 49 for MSI/MSI-X
[   19.840665] e1000e 0000:04:00.0: irq 49 for MSI/MSI-X
[   19.841043] bonding: bond0: enslaving eth0 as an active interface with a down link.
[   19.843998] bonding: bond0: Adding slave eth1.
[   19.919738] e1000e 0000:05:00.0: irq 50 for MSI/MSI-X
[   20.020615] e1000e 0000:05:00.0: irq 50 for MSI/MSI-X
[   20.020976] bonding: bond0: enslaving eth1 as an active interface with a down link.
[   20.289625] e1000e 0000:06:00.0: irq 51 for MSI/MSI-X
[   20.390543] e1000e 0000:06:00.0: irq 51 for MSI/MSI-X
[   20.391025] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   21.345478] e1000e 0000:07:00.0: irq 52 for MSI/MSI-X
[   21.446285] e1000e 0000:07:00.0: irq 52 for MSI/MSI-X
[   21.446770] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[   22.228107] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   22.260045] bonding: bond0: link status up for interface eth1, enabling it in 0 ms.
[   22.260049] bonding: bond0: link status definitely up for interface eth1, 1000 Mbps full duplex.
[   22.260052] bonding: bond0: making interface eth1 the new active one.
[   22.260606] device eth1 entered promiscuous mode
[   22.260621] bonding: bond0: first active interface up!
[   22.260632] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[   22.310089] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   22.360000] bonding: bond0: link status up for interface eth0, enabling it in 100 ms.
[   22.459996] bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex.
[   22.486581] md: md2 stopped.
[   22.487115] md: bind<sdh1>
[   22.487512] md/raid0:md2: md_size is 117222144 sectors.
[   22.487514] md: RAID0 configuration for md2 - 1 zone
[   22.487515] md: zone0=[sdh1]
[   22.487517]       zone-offset=         0KB, device-offset=         0KB, size=  58611072KB
[   22.487522] md2: detected capacity change from 0 to 60017737728
[   22.487686]  md2: unknown partition table
[   22.487964] md: md4 stopped.
[   22.795868] md: bind<sdb3>
[   22.796034] md: bind<sdg3>
[   22.796177] md: bind<sda3>
[   22.796558] md/raid:md4: not clean -- starting background reconstruction
[   22.796565] md/raid:md4: device sda3 operational as raid disk 0
[   22.796566] md/raid:md4: device sdg3 operational as raid disk 2
[   22.796567] md/raid:md4: device sdb3 operational as raid disk 1
[   22.796851] md/raid:md4: allocated 3292kB
[   22.796866] md/raid:md4: raid level 5 active with 3 out of 3 devices, algorithm 2
[   22.796867] RAID conf printout:
[   22.796868]  --- level:5 rd:3 wd:3
[   22.796869]  disk 0, o:1, dev:sda3
[   22.796870]  disk 1, o:1, dev:sdb3
[   22.796871]  disk 2, o:1, dev:sdg3
[   22.796897] md4: detected capacity change from 0 to 7991698522112
[   22.797122]  md4: unknown partition table
[   22.797365] md: md4: current auto_remap = 0
[   22.797368] md: md4: flushing inflight I/O
[   22.800924] md: resync of RAID array md4
[   22.800928] md: minimum _guaranteed_  speed: 1000 KB/sec/disk.
[   22.800929] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[   22.800931] md: using 128k window, over a total of 3902196544k.
[   22.800932] md: resuming resync of md4 from checkpoint.
[   23.349853] bio: create slab <bio-2> at 2
[   25.658962] flashcache: flashcache-1.0-2017-11-10-22:53 initialized
[   25.672725] flashcache: flashcache-1.0-syno-v25-pin-file-2017-11-10-22:53-debug initialized
[   25.695909] flashache: /dev/vg1/volume_1 exclude check success
[   25.701771] flashache: /dev/md2 exclude check success
[   25.706841] device-mapper: flashcache: Can handle failure in creation
[   25.713282] device-mapper: flashcache: Allocate 23244KB (26B per) mem for 915456-entry cache(capacity:57216MB, associativity:512, block size:128 sectors(64KB))
[   27.096180] BTRFS: device label 2017.12.14-15:23:54 v15217 devid 1 transid 293 /dev/mapper/cachedev_0
[   27.096546] BTRFS info (device dm-2): disabling disk space caching
[   27.096550] BTRFS: has skinny extents
[   28.933608] loop: module loaded
[   29.472901] iSCSI:target_core_rodsp_server.c:1017:rodsp_server_init RODSP server started, login_key(106f3f0378f5).
[   29.478643] iSCSI:extent_pool.c:757:ep_init syno_extent_pool successfully initialized
[   29.499344] iSCSI:target_core_device.c:571:se_dev_align_max_sectors Rounding down aligned max_sectors from 4294967295 to 4294967288
[   29.499445] iSCSI:target_core_lunbackup.c:358:init_io_buffer_head 512 buffers allocated, total 2097152 bytes successfully
[   29.529076] iSCSI:target_core_file.c:92:fd_attach_hba RODSP plugin for fileio is enabled.
[   29.529085] iSCSI:target_core_ep.c:862:ep_attach_hba RODSP plugin for epio is enabled.
[   29.529088] iSCSI:target_core_ep.c:869:ep_attach_hba ODX Token Manager is enabled.
[   29.807871] usbcore: registered new interface driver usblp
[   29.862078] usbcore: registered new interface driver usbhid
[   29.862081] usbhid: USB HID core driver
[   29.956664] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input2
[   29.956723] hid-generic 0003:0458:003A.0001: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[   29.956814] input: Dell Dell USB Entry Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.0/input/input3
[   29.956877] hid-generic 0003:413C:2107.0002: input: USB HID v1.10 Keyboard [Dell Dell USB Entry Keyboard] on usb-0000:00:1d.0-1.6/input0
[   32.181360] ata7.00: configured for UDMA/133
[   32.181367] ata7: EH complete
[   32.257836] device eth1 left promiscuous mode
[   33.154503] init: iscsi_pluginengined main process (12373) terminated with status 255
[   33.154539] init: iscsi_pluginengined main process ended, respawning
[   34.894580] ata8.00: configured for UDMA/133
[   34.894588] ata8: EH complete
[   34.961942] ata1.00: configured for UDMA/133
[   34.961950] ata1: EH complete
[   35.531767] ata2.00: configured for UDMA/133
[   35.531774] ata2: EH complete
[   36.725056] ata1.00: configured for UDMA/133
[   36.725063] ata1: EH complete
[   36.787052] ata2.00: configured for UDMA/133
[   36.787058] ata2: EH complete
[   36.796883] ata7.00: configured for UDMA/133
[   36.796887] ata7: EH complete
[   36.810369] ata8.00: configured for UDMA/133
[   36.810374] ata8: EH complete
[   55.394371] init: nmbd main process (15290) killed by TERM signal
[   83.145040] usb 2-1.3: USB disconnect, device number 3
[   84.611375] usb 2-1.3: new low-speed USB device number 5 using ehci-pci
[   84.710348] Got empty serial number. Generate serial number from product.
[   84.713975] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input4
[   84.714037] hid-generic 0003:0458:003A.0003: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  138.172569] usb 2-1.3: USB disconnect, device number 5
[  139.639237] usb 2-1.3: new low-speed USB device number 6 using ehci-pci
[  139.738459] Got empty serial number. Generate serial number from product.
[  139.742360] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input5
[  139.742448] hid-generic 0003:0458:003A.0004: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  193.200037] usb 2-1.3: USB disconnect, device number 6
[  194.665984] usb 2-1.3: new low-speed USB device number 7 using ehci-pci
[  194.766032] Got empty serial number. Generate serial number from product.
[  194.769788] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input6
[  194.769847] hid-generic 0003:0458:003A.0005: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  248.227525] usb 2-1.3: USB disconnect, device number 7
[  249.693860] usb 2-1.3: new low-speed USB device number 8 using ehci-pci
[  249.793043] Got empty serial number. Generate serial number from product.
[  249.796377] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input7
[  249.796411] hid-generic 0003:0458:003A.0006: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  303.255037] usb 2-1.3: USB disconnect, device number 8
[  304.721666] usb 2-1.3: new low-speed USB device number 9 using ehci-pci
[  304.820632] Got empty serial number. Generate serial number from product.
[  304.824261] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input8
[  304.824314] hid-generic 0003:0458:003A.0007: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  358.282503] usb 2-1.3: USB disconnect, device number 9
[  359.748564] usb 2-1.3: new low-speed USB device number 10 using ehci-pci
[  359.848662] Got empty serial number. Generate serial number from product.
[  359.852382] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input9
[  359.852419] hid-generic 0003:0458:003A.0008: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  413.309968] usb 2-1.3: USB disconnect, device number 10
[  414.776425] usb 2-1.3: new low-speed USB device number 11 using ehci-pci
[  414.875518] Got empty serial number. Generate serial number from product.
[  414.878859] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input10
[  414.878913] hid-generic 0003:0458:003A.0009: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  468.337495] usb 2-1.3: USB disconnect, device number 11
[  469.803783] usb 2-1.3: new low-speed USB device number 12 using ehci-pci
[  469.902753] Got empty serial number. Generate serial number from product.
[  469.906322] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input11
[  469.906349] hid-generic 0003:0458:003A.000A: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  523.364989] usb 2-1.3: USB disconnect, device number 12
[  524.830894] usb 2-1.3: new low-speed USB device number 13 using ehci-pci
[  524.930853] Got empty serial number. Generate serial number from product.
[  524.934709] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input12
[  524.934781] hid-generic 0003:0458:003A.000B: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  578.392463] usb 2-1.3: USB disconnect, device number 13
[  579.858507] usb 2-1.3: new low-speed USB device number 14 using ehci-pci
[  579.958354] Got empty serial number. Generate serial number from product.
[  579.961823] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input13
[  579.961884] hid-generic 0003:0458:003A.000C: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  633.419961] usb 2-1.3: USB disconnect, device number 14
[  634.885988] usb 2-1.3: new low-speed USB device number 15 using ehci-pci
[  634.985213] Got empty serial number. Generate serial number from product.
[  634.988723] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input14
[  634.988784] hid-generic 0003:0458:003A.000D: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  688.447439] usb 2-1.3: USB disconnect, device number 15
[  689.913594] usb 2-1.3: new low-speed USB device number 16 using ehci-pci
[  690.012458] Got empty serial number. Generate serial number from product.
[  690.016330] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input15
[  690.016389] hid-generic 0003:0458:003A.000E: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  743.474890] usb 2-1.3: USB disconnect, device number 16
[  744.941202] usb 2-1.3: new low-speed USB device number 17 using ehci-pci
[  745.040189] Got empty serial number. Generate serial number from product.
[  745.043656] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input16
[  745.043716] hid-generic 0003:0458:003A.000F: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  798.502421] usb 2-1.3: USB disconnect, device number 17
[  799.968722] usb 2-1.3: new low-speed USB device number 18 using ehci-pci
[  800.067557] Got empty serial number. Generate serial number from product.
[  800.071309] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input17
[  800.071370] hid-generic 0003:0458:003A.0010: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  853.529896] usb 2-1.3: USB disconnect, device number 18
[  854.996184] usb 2-1.3: new low-speed USB device number 19 using ehci-pci
[  855.095163] Got empty serial number. Generate serial number from product.
[  855.098628] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input18
[  855.098686] hid-generic 0003:0458:003A.0011: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  908.557368] usb 2-1.3: USB disconnect, device number 19
[  910.023812] usb 2-1.3: new low-speed USB device number 20 using ehci-pci
[  910.122899] Got empty serial number. Generate serial number from product.
[  910.126354] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input19
[  910.126416] hid-generic 0003:0458:003A.0012: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[  963.584839] usb 2-1.3: USB disconnect, device number 20
[  965.051408] usb 2-1.3: new low-speed USB device number 21 using ehci-pci
[  965.150387] Got empty serial number. Generate serial number from product.
[  965.153733] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input20
[  965.153793] hid-generic 0003:0458:003A.0013: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1018.612358] usb 2-1.3: USB disconnect, device number 21
[ 1020.079026] usb 2-1.3: new low-speed USB device number 22 using ehci-pci
[ 1020.177999] Got empty serial number. Generate serial number from product.
[ 1020.181594] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input21
[ 1020.181627] hid-generic 0003:0458:003A.0014: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1073.639861] usb 2-1.3: USB disconnect, device number 22
[ 1075.106772] usb 2-1.3: new low-speed USB device number 23 using ehci-pci
[ 1075.206740] Got empty serial number. Generate serial number from product.
[ 1075.210462] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input22
[ 1075.210522] hid-generic 0003:0458:003A.0015: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1128.667329] usb 2-1.3: USB disconnect, device number 23
[ 1130.133276] usb 2-1.3: new low-speed USB device number 24 using ehci-pci
[ 1130.233437] Got empty serial number. Generate serial number from product.
[ 1130.237209] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input23
[ 1130.237268] hid-generic 0003:0458:003A.0016: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1183.694779] usb 2-1.3: USB disconnect, device number 24
[ 1185.160988] usb 2-1.3: new low-speed USB device number 25 using ehci-pci
[ 1185.260921] Got empty serial number. Generate serial number from product.
[ 1185.264677] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input24
[ 1185.264741] hid-generic 0003:0458:003A.0017: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1238.722317] usb 2-1.3: USB disconnect, device number 25
[ 1240.188474] usb 2-1.3: new low-speed USB device number 26 using ehci-pci
[ 1240.288282] Got empty serial number. Generate serial number from product.
[ 1240.292087] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input25
[ 1240.292148] hid-generic 0003:0458:003A.0018: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1293.749782] usb 2-1.3: USB disconnect, device number 26
[ 1295.216136] usb 2-1.3: new low-speed USB device number 27 using ehci-pci
[ 1295.316059] Got empty serial number. Generate serial number from product.
[ 1295.319675] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input26
[ 1295.319707] hid-generic 0003:0458:003A.0019: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1348.777291] usb 2-1.3: USB disconnect, device number 27
[ 1350.243563] usb 2-1.3: new low-speed USB device number 28 using ehci-pci
[ 1350.342925] Got empty serial number. Generate serial number from product.
[ 1350.346597] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input27
[ 1350.346684] hid-generic 0003:0458:003A.001A: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1403.804728] usb 2-1.3: USB disconnect, device number 28
[ 1405.271145] usb 2-1.3: new low-speed USB device number 29 using ehci-pci
[ 1405.370029] Got empty serial number. Generate serial number from product.
[ 1405.373506] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input28
[ 1405.373566] hid-generic 0003:0458:003A.001B: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1458.832258] usb 2-1.3: USB disconnect, device number 29
[ 1460.298922] usb 2-1.3: new low-speed USB device number 30 using ehci-pci
[ 1460.398026] Got empty serial number. Generate serial number from product.
[ 1460.401647] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input29
[ 1460.401679] hid-generic 0003:0458:003A.001C: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1513.859723] usb 2-1.3: USB disconnect, device number 30
[ 1515.326517] usb 2-1.3: new low-speed USB device number 31 using ehci-pci
[ 1515.426392] Got empty serial number. Generate serial number from product.
[ 1515.429711] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input30
[ 1515.429743] hid-generic 0003:0458:003A.001D: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1568.887213] usb 2-1.3: USB disconnect, device number 31
[ 1570.353256] usb 2-1.3: new low-speed USB device number 32 using ehci-pci
[ 1570.452118] Got empty serial number. Generate serial number from product.
[ 1570.455578] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input31
[ 1570.455671] hid-generic 0003:0458:003A.001E: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1623.914671] usb 2-1.3: USB disconnect, device number 32
[ 1625.381018] usb 2-1.3: new low-speed USB device number 33 using ehci-pci
[ 1625.479855] Got empty serial number. Generate serial number from product.
[ 1625.483573] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input32
[ 1625.483604] hid-generic 0003:0458:003A.001F: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1678.942213] usb 2-1.3: USB disconnect, device number 33
[ 1680.408764] usb 2-1.3: new low-speed USB device number 34 using ehci-pci
[ 1680.507719] Got empty serial number. Generate serial number from product.
[ 1680.511041] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input33
[ 1680.511098] hid-generic 0003:0458:003A.0020: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1733.969709] usb 2-1.3: USB disconnect, device number 34
[ 1735.436361] usb 2-1.3: new low-speed USB device number 35 using ehci-pci
[ 1735.535291] Got empty serial number. Generate serial number from product.
[ 1735.538920] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input34
[ 1735.538981] hid-generic 0003:0458:003A.0021: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1788.997186] usb 2-1.3: USB disconnect, device number 35
[ 1790.463963] usb 2-1.3: new low-speed USB device number 36 using ehci-pci
[ 1790.562823] Got empty serial number. Generate serial number from product.
[ 1790.566131] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input35
[ 1790.566167] hid-generic 0003:0458:003A.0022: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1844.024624] usb 2-1.3: USB disconnect, device number 36
[ 1845.490725] usb 2-1.3: new low-speed USB device number 37 using ehci-pci
[ 1845.590641] Got empty serial number. Generate serial number from product.
[ 1845.594541] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input36
[ 1845.594594] hid-generic 0003:0458:003A.0023: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1899.052160] usb 2-1.3: USB disconnect, device number 37
[ 1900.518176] usb 2-1.3: new low-speed USB device number 38 using ehci-pci
[ 1900.617275] Got empty serial number. Generate serial number from product.
[ 1900.621039] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input37
[ 1900.621144] hid-generic 0003:0458:003A.0024: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 1954.079645] usb 2-1.3: USB disconnect, device number 38
[ 1955.545915] usb 2-1.3: new low-speed USB device number 39 using ehci-pci
[ 1955.644776] Got empty serial number. Generate serial number from product.
[ 1955.648518] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input38
[ 1955.648557] hid-generic 0003:0458:003A.0025: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2009.107104] usb 2-1.3: USB disconnect, device number 39
[ 2010.573429] usb 2-1.3: new low-speed USB device number 40 using ehci-pci
[ 2010.672640] Got empty serial number. Generate serial number from product.
[ 2010.676390] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input39
[ 2010.676420] hid-generic 0003:0458:003A.0026: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2064.134599] usb 2-1.3: USB disconnect, device number 40
[ 2065.601030] usb 2-1.3: new low-speed USB device number 41 using ehci-pci
[ 2065.699869] Got empty serial number. Generate serial number from product.
[ 2065.703343] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input40
[ 2065.703402] hid-generic 0003:0458:003A.0027: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2119.162058] usb 2-1.3: USB disconnect, device number 41
[ 2120.628654] usb 2-1.3: new low-speed USB device number 42 using ehci-pci
[ 2120.727364] Got empty serial number. Generate serial number from product.
[ 2120.730981] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input41
[ 2120.731039] hid-generic 0003:0458:003A.0028: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2174.189713] usb 2-1.3: USB disconnect, device number 42
[ 2175.656250] usb 2-1.3: new low-speed USB device number 43 using ehci-pci
[ 2175.755226] Got empty serial number. Generate serial number from product.
[ 2175.758945] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input42
[ 2175.758979] hid-generic 0003:0458:003A.0029: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2229.217072] usb 2-1.3: USB disconnect, device number 43
[ 2230.683733] usb 2-1.3: new low-speed USB device number 44 using ehci-pci
[ 2230.782670] Got empty serial number. Generate serial number from product.
[ 2230.786280] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input43
[ 2230.786312] hid-generic 0003:0458:003A.002A: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2284.244556] usb 2-1.3: USB disconnect, device number 44
[ 2285.711336] usb 2-1.3: new low-speed USB device number 45 using ehci-pci
[ 2285.811183] Got empty serial number. Generate serial number from product.
[ 2285.814584] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input44
[ 2285.814637] hid-generic 0003:0458:003A.002B: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2339.272004] usb 2-1.3: USB disconnect, device number 45
[ 2340.738944] usb 2-1.3: new low-speed USB device number 46 using ehci-pci
[ 2340.838942] Got empty serial number. Generate serial number from product.
[ 2340.842399] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input45
[ 2340.842458] hid-generic 0003:0458:003A.002C: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2394.299492] usb 2-1.3: USB disconnect, device number 46
[ 2395.765408] usb 2-1.3: new low-speed USB device number 47 using ehci-pci
[ 2395.864531] Got empty serial number. Generate serial number from product.
[ 2395.868261] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input46
[ 2395.868319] hid-generic 0003:0458:003A.002D: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2423.593995] perf interrupt took too long (2529 > 5000), lowering kernel.perf_event_max_sample_rate to 50000
[ 2449.327023] usb 2-1.3: USB disconnect, device number 47
[ 2450.793063] usb 2-1.3: new low-speed USB device number 48 using ehci-pci
[ 2450.893144] Got empty serial number. Generate serial number from product.
[ 2450.896917] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input47
[ 2450.896951] hid-generic 0003:0458:003A.002E: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2504.354501] usb 2-1.3: USB disconnect, device number 48
[ 2505.820679] usb 2-1.3: new low-speed USB device number 49 using ehci-pci
[ 2505.920519] Got empty serial number. Generate serial number from product.
[ 2505.924361] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input48
[ 2505.924420] hid-generic 0003:0458:003A.002F: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2559.381989] usb 2-1.3: USB disconnect, device number 49
[ 2560.848252] usb 2-1.3: new low-speed USB device number 50 using ehci-pci
[ 2560.948136] Got empty serial number. Generate serial number from product.
[ 2560.951856] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input49
[ 2560.951911] hid-generic 0003:0458:003A.0030: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2614.409477] usb 2-1.3: USB disconnect, device number 50
[ 2615.875763] usb 2-1.3: new low-speed USB device number 51 using ehci-pci
[ 2615.974985] Got empty serial number. Generate serial number from product.
[ 2615.978745] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input50
[ 2615.978833] hid-generic 0003:0458:003A.0031: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2669.436927] usb 2-1.3: USB disconnect, device number 51
[ 2670.903384] usb 2-1.3: new low-speed USB device number 52 using ehci-pci
[ 2671.002476] Got empty serial number. Generate serial number from product.
[ 2671.006236] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input51
[ 2671.006290] hid-generic 0003:0458:003A.0032: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2724.464460] usb 2-1.3: USB disconnect, device number 52
[ 2725.930857] usb 2-1.3: new low-speed USB device number 53 using ehci-pci
[ 2726.030220] Got empty serial number. Generate serial number from product.
[ 2726.033862] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input52
[ 2726.033920] hid-generic 0003:0458:003A.0033: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2779.491949] usb 2-1.3: USB disconnect, device number 53
[ 2780.958609] usb 2-1.3: new low-speed USB device number 54 using ehci-pci
[ 2781.057960] Got empty serial number. Generate serial number from product.
[ 2781.061820] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input53
[ 2781.061909] hid-generic 0003:0458:003A.0034: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0
[ 2834.519424] usb 2-1.3: USB disconnect, device number 54
[ 2835.986222] usb 2-1.3: new low-speed USB device number 55 using ehci-pci
[ 2836.086070] Got empty serial number. Generate serial number from product.
[ 2836.089777] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input54
[ 2836.089836] hid-generic 0003:0458:003A.0035: input: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.0-1.3/input0


0000:00:00.0 Class 0600: Device 8086:0108 (rev 09)
    Subsystem: Device 8086:0108
0000:00:01.0 Class 0604: Device 8086:0101 (rev 09)
    Kernel driver in use: pcieport
0000:00:01.1 Class 0604: Device 8086:0105 (rev 09)
    Kernel driver in use: pcieport
0000:00:02.0 Class 0300: Device 8086:010a (rev 09)
    Subsystem: Device 8086:010a
0000:00:16.0 Class 0780: Device 8086:1c3a (rev 04)
    Subsystem: Device 8086:1c3a
0000:00:1a.0 Class 0c03: Device 8086:1c2d (rev 05)
    Subsystem: Device 8086:1c2d
    Kernel driver in use: ehci-pci
0000:00:1b.0 Class 0403: Device 8086:1c20 (rev 05)
    Subsystem: Device 8086:1c20
0000:00:1c.0 Class 0604: Device 8086:1c10 (rev b5)
    Kernel driver in use: pcieport
0000:00:1c.4 Class 0604: Device 8086:1c18 (rev b5)
    Kernel driver in use: pcieport
0000:00:1c.5 Class 0604: Device 8086:1c1a (rev b5)
    Kernel driver in use: pcieport
0000:00:1c.6 Class 0604: Device 8086:1c1c (rev b5)
    Kernel driver in use: pcieport
0000:00:1c.7 Class 0604: Device 8086:1c1e (rev b5)
    Kernel driver in use: pcieport
0000:00:1d.0 Class 0c03: Device 8086:1c26 (rev 05)
    Subsystem: Device 8086:1c26
    Kernel driver in use: ehci-pci
0000:00:1e.0 Class 0604: Device 8086:244e (rev a5)
0000:00:1f.0 Class 0601: Device 8086:1c56 (rev 05)
    Subsystem: Device 8086:1c56
    Kernel driver in use: lpc_ich
0000:00:1f.2 Class 0106: Device 8086:1c02 (rev 05)
    Subsystem: Device 8086:1c02
    Kernel driver in use: ahci
0000:00:1f.3 Class 0c05: Device 8086:1c22 (rev 05)
    Subsystem: Device 8086:1c22
0000:02:00.0 Class 0104: Device 1b4b:9485 (rev 03)
    Subsystem: Device 1b4b:9485
0000:03:00.0 Class 0106: Device 1b4b:9125 (rev 11)
    Subsystem: Device 1b4b:9125
    Kernel driver in use: ahci
0000:04:00.0 Class 0200: Device 8086:10d3
    Subsystem: Device 8086:0000
    Kernel driver in use: e1000e
0000:05:00.0 Class 0200: Device 8086:10d3
    Subsystem: Device 8086:0000
    Kernel driver in use: e1000e
0000:06:00.0 Class 0200: Device 8086:10d3
    Subsystem: Device 8086:0000
    Kernel driver in use: e1000e
0000:07:00.0 Class 0200: Device 8086:10d3
    Subsystem: Device 8086:0000
    Kernel driver in use: e1000e
0001:07:00.0 Class 0000: Device 1b4b:9235 (rev ff)
0001:08:00.0 Class 0000: Device 1b4b:9235 (rev ff)
0001:09:00.0 Class 0000: Device 1b4b:9235 (rev ff)
0001:0a:00.0 Class 0000: Device 1b4b:9235 (rev ff)

 

Hide  


 

 

Edited by Polanskiman
Added code tag and spoiler tag. Please use them in the future.

Share this post


Link to post
Share on other sites
11 minutes ago, brunokelo said:

0000:02:00.0 Class 0104: Device 1b4b:9485 (rev 03)
    Subsystem: Device 1b4b:9485

 

thats our unknown/not detected controller a Marvell 88SE9485

but 9485 is in the source of mvsas

try unload driver with rmmod and load it with insmod, see /var/log messages if there is something about the loading then

Share this post


Link to post
Share on other sites
sudo tail -f /var/log/messages
2017-12-14T21:38:40-02:00 STR-BRUNO kernel:[ 3991.662194] Got empty serial number. Generate serial number from product.
2017-12-14T21:39:35-02:00 STR-BRUNO kernel: [ 4046.689784] Got empty serial number. Generate serial number from product.
2017-12-14T21:40:30-02:00 STR-BRUNO kernel: [ 4101.717398] Got empty serial number. Generate serial number from product.
2017-12-14T21:41:26-02:00 STR-BRUNO kernel: [ 4156.744858] Got empty serial number. Generate serial number from product.
2017-12-14T21:42:21-02:00 STR-BRUNO kernel: [ 4211.772449] Got empty serial number. Generate serial number from product.
2017-12-14T21:43:16-02:00 STR-BRUNO kernel: [ 4266.799065] Got empty serial number. Generate serial number from product.
2017-12-14T21:44:11-02:00 STR-BRUNO kernel: [ 4321.826835] Got empty serial number. Generate serial number from product.
2017-12-14T21:45:06-02:00 STR-BRUNO kernel: [ 4376.856074] Got empty serial number. Generate serial number from product.
2017-12-14T21:46:01-02:00 STR-BRUNO kernel: [ 4431.882056] Got empty serial number. Generate serial number from product.
2017-12-14T21:46:56-02:00 STR-BRUNO kernel: [ 4486.911007] Got empty serial number. Generate serial number from product.
2017-12-14T21:47:51-02:00 STR-BRUNO kernel: [ 4541.936661] Got empty serial number. Generate serial number from product.

 

Edited by Polanskiman
Added code tag. Please use them in the future.

Share this post


Link to post
Share on other sites

@brunokelo You are advised to use proper code tags when posting code. copy pasting plain text code without tags make it difficult to read. Also please do no post images for code.

Share this post


Link to post
Share on other sites
1 hour ago, Polanskiman said:

@brunokelo You are advised to use proper code tags when posting code. copy pasting plain text code without tags make it difficult to read. Also please do no post images for code.

 

ok, sorry. 

Share this post


Link to post
Share on other sites
11 hours ago, IG-88 said:

found this

https://ubuntuforums.org/showthread.php?t=2281480

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1270844

 

moded the kernel source and made a new mvsas.ko

try this extra.lzma testversion if it detects your controller

http://s000.tinyupload.com/?file_id=85643652075732261500

 

 

Thank you again, but I still have not recognized the discs. 

Share this post


Link to post
Share on other sites
admin@STR-BRUNO:/$ dmesg | grep sas
[    3.868714] megasas: 06.506.00.00-rc1 Sat. Feb. 9 17:00:00 PDT 2013
[    3.871800] mpt2sas version 20.00.00.00 loaded
[    3.874799] mpt3sas version 01.100.01.00 loaded

has not uploaded the mvsas module

Share this post


Link to post
Share on other sites

I think the 1b4b:9235 class 0000 device is another 4 port marvell sata controller  -  might there be some testing/work to sort out 3 controllers (4+4+8?) sataportmap settings maybe or adjust drives to 16?

Also, I spotted this page about the sas driver not binding, not my area of expertise, but maybe it gives a hint?

https://github.com/ArchAssault-Project/archassault/blob/master/packages/linux-archassault/mvsas-Recognise-device-subsystem-9485-9485-as-88SE94.patch

 

Also, I wonder if it may be worth disabling spare devices (second serial port, additional USB etc) in case there are resource conflicts between devices, maybe the XPE/DSM driver/module wont load in 'shared' space?

I'm using several mvsas driven (supermicro AOC) cards with 5.2 and 6 (with @IG-88 enhanced extra.lzma) and they work fine - maybe try 5.2 just as a test/diagnostic?

 

Share this post


Link to post
Share on other sites

class 00 is unclassified device, 01 would be storage also 88SE92xx would be a AHCI chip

in the live linux boot screen there is a mvsas device and thats the one missing in dsm, so i guess the ports missing are indeed the 88se9485

 

the patch i mentioned above and used for the test was accepted by kernel.org to cope with the 9485 detection but was for a actual kernel, might not work properly

i had a peek in the last 3.16 mvsas driver from kernel.org, mod looks like the one sbv3000 linked, so i did a new one

http://s000.tinyupload.com/?file_id=44597107618672818277

 

Share this post


Link to post
Share on other sites
1 hour ago, IG-88 said:

class 00 is unclassified device, 01 would be storage also 88SE92xx would be a AHCI chip

in the live linux boot screen there is a mvsas device and thats the one missing in dsm, so i guess the ports missing are indeed the 88se9485

 

the patch i mentioned above and used for the test was accepted by kernel.org to cope with the 9485 detection but was for a actual kernel, might not work properly

i had a peek in the last 3.16 mvsas driver from kernel.org, mod looks like the one sbv3000 linked, so i did a new one

http://s000.tinyupload.com/?file_id=44597107618672818277

 

 

 

sudo dmesg | grep sas
[    3.871244] megasas: 06.506.00.00-rc1 Sat. Feb. 9 17:00:00 PDT 2013
[    3.874320] mpt2sas version 20.00.00.00 loaded
[    3.877347] mpt3sas version 01.100.01.00 loaded


-rw-r--r-- 1 root root    82336 Sep 10 19:35 mvsas.ko

still nothing, I'm out of luck, I think I'll buy a LSI SATA controller.

Edited by brunokelo

Share this post


Link to post
Share on other sites

date of the file does not match, its a old one, the new one in extra.lzma is from today

delete mvsas.ko in /lib/modules and /lib/modules/update and reboot

mvsas.ko should reappear from the extra.lzma on boot media

 

 

Share this post


Link to post
Share on other sites
29 minutes ago, IG-88 said:

date of the file does not match, its a old one, the new one in extra.lzma is from today

delete mvsas.ko in /lib/modules and /lib/modules/update and reboot

mvsas.ko should reappear from the extra.lzma on boot media

 

 

 

I unzipped the extra.lzma file and via scp I sent the file mvsas.ko into the folder / lib / modules / update then removed and added the module again and now recognized all the disks !!!

When I reboot the old mvsas module, I'm not adding the extra.lzma correctly to my usb pendrive?

Share this post


Link to post
Share on other sites

Update: I deleted the pendrive with a low level formatting program, I recorded the image again in it, and now it worked correctly, it found all the disks !!!!


IG-88,  would like to thank you very much for your help !!!! Thank you very much !!! I am very happy !!!!! excellent job !!!! 

 

 

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now