liukuohao Posted August 11, 2014 Author Share #76 Posted August 11, 2014 Did a lot more testing. Most success found with this BIOS...http://www.hardwareluxx.de/community/f1 ... st21503128 If you don't touch Task Scheduler then my N54L keeps it's BIOS settings. As soon as you create a task and restart - BIOS is changed. Even if you use Advanced Power Management pack it changes the the BIOS. "The Bays" BIOS gets changed no matter what. The changes made to the BIOS in both cases most people won't probably even notice. Splash Screen gets re-enabled. After Power Loss gets set to Last State. I even tried an old MSI motherboard (P35 Platinum - about 4 to 5 years old). This has a AMI BIOS and it too got changed - more significantly than the N54L it created checksum errors. Hi Bod, Thanks for your feedback. Are you right about not touching the Task Scheduler, and you don't have BIOS resetting problem? So, this is true, I guess that is reason why the forum users did not highlight this is a common problem since Task Scheduler is not a popular settings to be used, I suppose. Anyway thank for your further testing. I suggest you stick to ASUS motherboards. So far, I found any BIOS resetting problem using Nanoboot. Quote Link to comment Share on other sites More sharing options...
snoopy78 Posted August 13, 2014 Share #77 Posted August 13, 2014 for me i only have the issue when i enable the auto start feature with the auto shutdown i do not get this issue on both of my systems Supermicro X8SIL-F and HPML310 G8v1 Quote Link to comment Share on other sites More sharing options...
liukuohao Posted August 15, 2014 Author Share #78 Posted August 15, 2014 Ok thanks for the feedback, I wonder if there is motherboard that is 100% compatible available in market, so we don't have to keep testing. Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 1, 2014 Author Share #79 Posted September 1, 2014 Well...I have been very busy over last few weeks...did not have time to test out more motherboards to see if there is any issue in regards of bios resetting problem. But now...because I am having a long weekend, I manage to get my hands tested on ASUS P5G41CM-LX-http://www.asus.com/Motherboards/P5G41CM_LX/motherboard. The result..... Under Power Schedule tab (from Hardware & Power), I created a schedule to shut down the system daily at 18:35. The system did shutdown as expected... So, I press the start button on my PC, XPEnology system reboot up and there is no bios resetting problem/bios checksum error message appear, it booted as per normal. By the way, just want to inform all the forum users that BrainAz had tested that his Gigabyte motherboard Gigabyte GA-EP45-UD3R from http://xpenology.com/forum/viewtopic.php?f=2&t=3806#p22751, managed to survive a bios resetting/ bios check sum error problem due to his motherboard's dual bios in action. Quote Link to comment Share on other sites More sharing options...
She Posted September 1, 2014 Share #80 Posted September 1, 2014 at my hp n54l the reset occurs only when you schedule start up and not shut down. so you may like to test scheduling a start up as well, just to be sure. Quote Link to comment Share on other sites More sharing options...
jbugman Posted September 1, 2014 Share #81 Posted September 1, 2014 There maybe another way to solve this..... Reading on a HP server site for a server software that was causing a corrupt bios upon reboot, someone commented that to get a reboot to work and not have a corrupt bios, all they had to do was to password lock the bios Anyone care to try it???? J Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 2, 2014 Author Share #82 Posted September 2, 2014 (edited) at my hp n54l the reset occurs only when you schedule start up and not shut down.so you may like to test scheduling a start up as well, just to be sure. Hi She, So....I did play around with power schedule again this morning, and tested on the start up instead of earlier shutdown feature (tested on yesterday late afternoon) My result is.... start up (meaning schedule to start up at 8.30 am, just for example) did MESS up my ASUS bios setting. After the time has reached 8.30 am, the PC did automatically start up. But boot to DSM cannot proceed, because it stuck there in the beginning of POST, asking me to: Press F1 to Run SETUP Press F2 to load default values and continue So...She as you predicted, schedule to start up causes my ASUS bios reset I must try on the Gigabyte motherboard with dual-bios chip and see whether start up is causing BIOS resetting or not. However, just to repeat myself, scheduled shutdown works and... after I pressed the button to turn on the system when it has completely shut down, there is no bios resetting / no bios check sum error during booting up in POST . From me, the biggest worry is resetting BIOS after every reboot, however my ASUS P5G41CM-LX-http://www.asus.com/Motherboards/P5G41CM_LX/motherboard, does not have this problem so my worry is gone. If the power schedule of start up is not working, and shut down is working, I can live with that , and ultimately, at least I can sleep easy at night and stop worrying the resetting bios problem I can conclude that...to find a motherboard that match 100% compatible with a system hardware of an original Synology DS3612xs is quite impossible. DSM will always be 80-90% compatible with our own motherboard of choice. So, you expect to have some incompatibilities in some of the DSM software functions / features. Edited September 2, 2014 by Guest Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 2, 2014 Author Share #83 Posted September 2, 2014 There maybe another way to solve this..... Reading on a HP server site for a server software that was causing a corrupt bios upon reboot, someone commented that to get a reboot to work and not have a corrupt bios, all they had to do was to password lock the bios Anyone care to try it???? J If anyone of forum user owns a HP N54L system, please do a password locking in the bios and see whether it will solve the resetting bios problem during booting in POST, as I don't own one myself. I tried on my very 1st system, the Supermicro PDSME motherboard with passwork locking in bios but it didn't prevent the bios resetting happening. Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 4, 2014 Author Share #84 Posted September 4, 2014 Hi All, Just another update on my testing motherboards. Please don't bother to use /buy this ASROCK socket 775 motherboard: http://www.asrock.com/mb/Intel/G41C-GS%20R2.0/ It is the ASROCK G41C-GS R2.0 You are wasting your time and money Why? This motherboard will get BIOS check sum error (or BIOS being reset) on every time you reboot/restart DSM. So you are being warn! Quote Link to comment Share on other sites More sharing options...
Hyperbit Posted September 10, 2014 Share #85 Posted September 10, 2014 I got a N40L, the Solution "Setup a Passwort to the BIOS" does not work. I Tryd Advanced Power Manger and the buildin energymanager. Booth destroy the BIOS-Settings with and without BIOS_Passwordprotection. In my case, it does not hurt me cause i only use 4 Drives at the Moment and no special Hackedbiosfeatures are needed, but a solution would be nice. Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 11, 2014 Author Share #86 Posted September 11, 2014 I got a N40L, the Solution "Setup a Passwort to the BIOS" does not work. Same goes with my Asus motherboards, having password protected in its BIOS setting DOES NOT WORK. Meaning if I set up automatically to boot up (scheduled to boot up) when the system starts up, it reset my bios setting and having BIOS password enabled did not prevent it at all. However, automatically shut down and start up again did not cause any BIOS resetting problem. But I did saw someone using HP microserver n54l. mentioned that BIOS password did work!.http://xpenology.com/forum/viewtopic.php?f=2&t=3073 Unfortunately, I cannot verify it at all, because I don't have one! Thanks Quote Link to comment Share on other sites More sharing options...
Hyperbit Posted September 11, 2014 Share #87 Posted September 11, 2014 N40L uses the same BIOS AS N54L .The Mainboard istbthe Same. I would Like to know on which DSM and Which BIOS there will no reset with password protection. Maybee a special event spk will help ??! Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 11, 2014 Author Share #88 Posted September 11, 2014 N40L uses the same BIOS AS N54L .The Mainboard istbthe Same. I would Like to know on which DSM and Which BIOS there will no reset with password protection. Maybee a special event spk will help ??! I wish that I can offer any help. But as I said earlier, I don't have any HP microserver to test. My topic is mainly concerning about 3rd party motherboard used for testing DSM. I am not sure what you mentioned about "special event spk will help" Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 11, 2014 Author Share #89 Posted September 11, 2014 (edited) Hi All, Just another update on my testing motherboards. Please don't bother to use /buy this ASROCK socket 775 motherboard: http://www.asrock.com/mb/Intel/G41C-GS%20R2.0/ It is the ASROCK G41C-GS R2.0 You are wasting your time and money Why? This motherboard will get BIOS check sum error (or BIOS being reset) on every time you reboot/restart DSM. So you are being warn! Hi All, I managed to test some more motherboards from Asrock over last week. Unfortunately, the 2 motherboards that I tested were far far worst than I expected. Both the motherboards fail to completely loading up NANOBOOT during installation. Both the motherboards will hang during when NANOBOOT is loading the drivers. You have to press the reset button, to boot up from POST again. In short, both the motherboards shown below, are not compatible with NANOBOOT. 1) Asrock G41M-VS3 R2.0 = http://www.asrock.com/mb/intel/g41m-vs3%20r2.0/ 2) Asrock G31M-GS R2.0 = http://www.asrock.com/mb/Intel/G31M-GS%20R2.0/ So you are being warned! Edited September 11, 2014 by Guest Quote Link to comment Share on other sites More sharing options...
liukuohao Posted September 11, 2014 Author Share #90 Posted September 11, 2014 Hi All, Just another update on my testing motherboards. Please don't bother to use /buy this ASROCK socket 775 motherboard: http://www.asrock.com/mb/Intel/G41C-GS%20R2.0/ It is the ASROCK G41C-GS R2.0 You are wasting your time and money Why? This motherboard will get BIOS check sum error (or BIOS being reset) on every time you reboot/restart DSM. So you are being warn! Hi All, This is yet another update... I managed to test some more motherboards from Asrock over last week. Unfortunately, the 2 motherboards that I tested were far far worst than I expected. Both the motherboards fail to completely loading up NANOBOOT during installation. Both the motherboards will hang during when NANOBOOT is loading the drivers. You have to press the reset button, to boot up from POST again. In short, both the motherboards shown below, it not compatible with NANOBOOT. 1) Asrock G41M-VS3 R2.0 = http://www.asrock.com/mb/intel/g41m-vs3%20r2.0/ 2) Asrock G31M-GS R2.0 = http://www.asrock.com/mb/Intel/G31M-GS%20R2.0/ So you are being warned! Quote Link to comment Share on other sites More sharing options...
Balrog Posted December 21, 2014 Share #91 Posted December 21, 2014 Workaround for BIOS Reset for HP Microserver Gen8 - Press F9 at boot to enter BIOS - Make your settings as desired (e.g. disable network boot and set the RAID-Controller into AHCI-Mode) - Choose "System Default Options" - "User Default Options" - "Save User Defaults" => this makes the actual settings to the new default settings. The Server starts instantly new and the new "Default Settings" are surviving the CMOS corruption forced by Xpenology at the shutdown or restart-process. The Date is of course false and set to 06.06.14 but this can be managed easily within Xpenology where you can set a NTP-Server as clock-source. Then the date will be corrected after the boot. I write this for all users as this bug costs me about 2 days.... Quote Link to comment Share on other sites More sharing options...
liukuohao Posted December 22, 2014 Author Share #92 Posted December 22, 2014 Workaround for BIOS Reset for HP Microserver Gen8 - Press F9 at boot to enter BIOS - Make your settings as desired (e.g. disable network boot and set the RAID-Controller into AHCI-Mode) - Choose "System Default Options" - "User Default Options" - "Save User Defaults" => this makes the actual settings to the new default settings. The Server starts instantly new and the new "Default Settings" are surviving the CMOS corruption forced by Xpenology at the shutdown or restart-process. The Date is of course false and set to 06.06.14 but this can be managed easily within Xpenology where you can set a NTP-Server as clock-source. Then the date will be corrected after the boot. I write this for all users as this bug costs me about 2 days.... Hi, Balrog, Thank you for sharing your contribution about a workaround for BIOS resetting issue on the HP Microserver Gen8 I hope users in the forum who owns a HP Mircroserver Gen8 can test it out to see if it is working or not. Since, I don't have one to try. Anyway.........someone out there, has to do some dirty work and hours and hours of testing for the betterment of getting Xpenology to be more compatible with our 3rd party hardware. Thank you again..... Quote Link to comment Share on other sites More sharing options...
liukuohao Posted December 22, 2014 Author Share #93 Posted December 22, 2014 Workaround for BIOS Reset for HP Microserver Gen8 - Press F9 at boot to enter BIOS - Make your settings as desired (e.g. disable network boot and set the RAID-Controller into AHCI-Mode) - Choose "System Default Options" - "User Default Options" - "Save User Defaults" => this makes the actual settings to the new default settings. The Server starts instantly new and the new "Default Settings" are surviving the CMOS corruption forced by Xpenology at the shutdown or restart-process. The Date is of course false and set to 06.06.14 but this can be managed easily within Xpenology where you can set a NTP-Server as clock-source. Then the date will be corrected after the boot. I write this for all users as this bug costs me about 2 days.... Hi, Balrog, Thank you for sharing your contribution about a workaround for BIOS resetting issue on the HP Microserver Gen8 I hope users in the forum who owns a HP Mircroserver Gen8 can test it out to see if it is working or not. Since, I don't have one to try. Anyway.........someone out there, has to do some dirty work and hours and hours of testing for the betterment of getting Xpenology to be more compatible with our 3rd party hardware. Thank you again..... Quote Link to comment Share on other sites More sharing options...
liukuohao Posted December 22, 2014 Author Share #94 Posted December 22, 2014 Hi All, Just another update on my testing motherboards. Please don't bother to use /buy this ASROCK socket 775 motherboard: http://www.asrock.com/mb/Intel/G41C-GS%20R2.0/ It is the ASROCK G41C-GS R2.0 You are wasting your time and money Why? This motherboard will get BIOS check sum error (or BIOS being reset) on every time you reboot/restart DSM. So you are being warn! Hi All, This is yet another update... I managed to test some more motherboards from Asrock over last week. Unfortunately, the 2 motherboards that I tested were far far worst than I expected. Both the motherboards fail to completely loading up NANOBOOT during installation. Both the motherboards will hang during when NANOBOOT is loading the drivers. You have to press the reset button, to boot up from POST again. In short, both the motherboards shown below, it not compatible with NANOBOOT. 1) Asrock G41M-VS3 R2.0 = http://www.asrock.com/mb/intel/g41m-vs3%20r2.0/ 2) Asrock G31M-GS R2.0 = http://www.asrock.com/mb/Intel/G31M-GS%20R2.0/ So you are being warned! PLEASE IGNORE THE MESSAGE ABOVE, NANOBOOT WAS NOT ABLE LOAD DURING INSTALLATION BECAUSE I HAD AN OLD PSU WHICH IS NOT COMPATIBLE WITH THE NEW MOTHERBOARDS LISTED ABOVE. Quote Link to comment Share on other sites More sharing options...
holybabel Posted December 29, 2014 Share #95 Posted December 29, 2014 Any news about this problem? I have a ss4200 and with Advanced Power Managment i get a bios error on startup. Shutdown works without problem. Quote Link to comment Share on other sites More sharing options...
liukuohao Posted December 30, 2014 Author Share #96 Posted December 30, 2014 (edited) Any news about this problem? I have a ss4200 and with Advanced Power Managment i get a bios error on startup. Shutdown works without problem. At first, I did not know what is ss4200, until I look up in Google..... Ok, frankly, I don't have the answer to your question unless I am the actual creator/designer of Synology DSM My advice is, if you really want to boot up automatically then here is the solution (may not be solution to you) Note: This solution only works for automatically start up only. 1) Buy a power AC auto timer. Set the time to turn on your SS4200 at certain time, say...everyday at 10.00am. 2) Go to bios and see whether you can enable a setting for AC power loss, enable this setting. This means that when there is a sudden power coming into your SS4200, it will turn on and boot to DSM automatically. 3) Plug in the AC auto timer into your wall power outlet, and then plug in the power cord of SS4200 into the AC auto timer. 4) Plug in the power cord of the other end, into your SS4200. You are done! Your SS4200 will turn on automatically everyday at 10.00am, however, allow the DSM to turn off the automatically in Power Schedule I hope this solution will solve the problem of yours. Or alternatively, look for an Intel DQ35J0E motherboard, I have tested personally the auto ON and OFF both is working flawlessly, except it does not support AHCI or not working properly in BIOS. if turn on AHCI, the system will hung. Edited January 1, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
holybabel Posted December 31, 2014 Share #97 Posted December 31, 2014 Hi, simple but nice idea. I think i will try it this way. Quote Link to comment Share on other sites More sharing options...
partyguy81 Posted January 17, 2015 Share #98 Posted January 17, 2015 Hello, Edit: was not working for me. I thought I had a solution. Quote Link to comment Share on other sites More sharing options...
liukuohao Posted January 18, 2015 Author Share #99 Posted January 18, 2015 Hi thanks for your input, I notice your motherboard is a Foxconn motherboard which is behaving not like other mainstream motherboards do when XPEnology is loaded on the system. That is, majority symptom is when play with the Power Schedule(set a time to shut down or boot up), the BIOS will be reset to default, requires user to manually input its settings But in your case, your Foxconn motherboard is able to shutdown properly without screwing up the BIOS. Well it is good to hear your feedback [emoji41] Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
partyguy81 Posted January 18, 2015 Share #100 Posted January 18, 2015 (edited) sorry double post Edited January 18, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.