Leaderboard

I haven't been here in a while But my xpenology Gave up the ghost and Brought a Dell PowerEdge T110 Server Tower I ended up removing the SAS card and just using SATA Following the instructions from this youtube Vid Was able to Get the Dell Running fine on 7.1 Thank to everyone who help with this hobbie

I ve tested it before on 0.9.2.9 thats why I said it was working flawlessly I think Pocopico made the most stable release with 0.9.2.9. I think this version need to be made offline or at least as Main stable. Really no bugs or at least I havent seen any besides some small problems with VM hdds but its easy fixable. Ok I applied fix, all shows thanks a lot, you are the best even no HDD error in VM In order to fix "No disk detected" error in UserConfig sata settings must be as follows "SataPortMap": "58", "DiskIdxMap": "0A00"

Since you want to use TCRP again, you want to monitor your Sata Port or Sata controller status. Can you tell me the result with the below command in TCRP Linux prompt? lspci -tvnnq

Several causes of kernel panic have been identified in jun's mod, and the rploader.sh file has been modified accordingly. Please try again using the modified method below. ------------------------------------------------------------ ------------------------------- [How to fix to M Shell Jun / Jot mode available version (22.10.22)] curl -L "https://github.com/PeterSuh-Q3/tinycore-redpill/raw/5d18c3ffd4125c9b8c7f753256c9d35ddc0fbc13/myfunc.h" -O curl -L "https://github.com/PeterSuh-Q3/tinycore-redpill/raw/3b01805c68fd991e59807fe6f3482e70b01be0a6/rploader.sh" -O And, to prevent automatic update to the final version of M shell Edit my.sh and comment out both lines 61 and 230 with # ------------------------------------------------------------ ------------------------------- In my case, there was another cause that caused the kernel panic, It was caused by randomly stretching the third partition in the VM to build multiple models. Even though the capacity is sufficient, if it exceeds a certain capacity, a message of insufficient space continues to appear, and in the end, this third partition seems to have been damaged. After replacing the vmdk file with the new 0.9.2.9 version, this phenomenon disappeared. Tested DS3622xs+, DS918+, DVA3219, etc in VM and bare metal. It works flawlessly.

Ну и Аллилуйя ..... Рад, что всё у вас получилось )))

ARPL is based on jun's mod. TCRP is based on jot's mod. The difference between the two is explained so much that you can find it just by searching with the keyword jot. If a switch occurs between these two modes, the system partition is sometimes initialized. So, be careful when you come across DSM's reinstallation message. Usually, it enters DSM booting without any message or asks for migration if migration is required. If you get a message other than that, don't proceed. The system partition is initialized and all packages are initialized as well.

загрузчик надо создавать командами как в первом посте ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh identifyusb now ./rploader.sh satamap now ./rploader.sh serialgen нужная модель now ./rploader.sh build -нужная модель и версия системы перегружаемся и ищем сино в ассистенте - покажет на каком она ip - переходи на него и следуем инструкциям

pocopico's satamap function can help with configuration as pocopico described, but not absolutely. I also don't trust this satamap function. And it doesn't even try to make it more sophisticated in the m shell. Recently, I guide users to always empty the SataPortMap and DIskIdxMap values. Of course, the graphically mapped part of the Synology Disk overview may look strange, but there is no problem in functionality. If a part of the disk is not visible, then you have to use it by modifying the SataPortMap inevitably.

[How to fix to M Shell Jun / Jot mode available version (22.10.22)] curl -L "https://github.com/PeterSuh-Q3/tinycore-redpill/raw/5d18c3ffd4125c9b8c7f753256c9d35ddc0fbc13/myfunc.h" -O curl -L "https://github.com/PeterSuh-Q3/tinycore-redpill/raw/30443567f58256a84d0225ee16182eab4b6c3e7c/rploader.sh" -O And, to prevent automatic update to the final version of M shell Edit my.sh and comment out both lines 61 and 230 with # ------------------------------------------------------------ ------------------------------- I've retested Jun's Mod and Jot's Mod of DVA3219 on bare metal for you now. Jun's Mod messed up what was the problem (probably a mistake in the process of migrating custom.gz as advised by pocopico. Driver could not be loaded) Only bare metal Jot's Mod seems to work. Jun's Mod and Jot's Mod's VMs go into kernel panic. I can no longer use my time and energy. Please switch to any other method available to you. Please use ARPL for Jun mode. Most of the models available in M Shell, including the DVA3219, have been requested from fabio to be supported by ARPL. The bottom line is that the only situation where the DVA3219 is possible is in bare metal Jot mode. Finally, DVA3219 will also continue the stabilization test at TCRP FRIEND. Please consider switching to using TCRP FRIEND in the future. Thank you.

Thanks for info, question, is it possible to download and put to TC folder last version of M Shell with Jun and Jot instead of using command to download latest version where its not there? Or is it possible to leave it there on list as it was but not support it anymore? You could just leave files on github with latest version that had them on the list if possible. Jot/Jun works fine with DVA3221/3219 the way it is the reason I am asking is that I want to test them out on older system without fma3 and try to make it work as well as emulate instructions and it takes some time, if I will succeed it will be good alternative for those with old cpus. The more versions are there on the list the better for testing purpose. But totally agree it takes a lot of energy so its totally understandable why you discontinue. You guys already did a very big job and thank you very much for your work

Is it possible to blank the two values like below and rebuild the TCRP FRIEND loader? If it is left blank, the loader automatically maps the SATA port. "SataPortMap": "", "DiskIdxMap": "" By the way, your usb_line / sata_line content is a bit strange. Did you manually delete sataportmap/DiskIdxMap by directly changing user_config.json?

Synology suggest an intermediate step :