IG-88 Posted October 29, 2019 Share #101 Posted October 29, 2019 18 hours ago, cpuks said: So does this module going to work on 3615 6.2.2 microserver gen8? yes, for anything below that is already support in the spk 18 hours ago, cpuks said: How can I install this? Download spk and module and replace it then install in package center? you install the spk and then replace the hpilo.ko the spk installed with the new one Quote Link to comment Share on other sites More sharing options...
IG-88 Posted October 29, 2019 Share #102 Posted October 29, 2019 On 10/28/2019 at 4:53 PM, youhq said: Thank you very much, 918+ can be used, but it seems that either 918 or 3615 does not seem to work. its kind of hard to tell what you try to say, did you try both? loader 1.03b with 3615 DSM 6.2.2. loader 1.04b with 918+ DSM 6.2.2 16 hours ago, youhq said: 3615 uses spk installation, 04-hd max is also unrecognizable also not sure what you trying to say, you used 3615 dsm 6.2.2 with the original spk? whats 04-hd max? 8 hours ago, youhq said: Can I compile a 2.9.1? the driver need to be compiled, the spk is a dsm compatible version of what hp released as rpm after installing the spk (2.5.0) i'd expect you extract the files from the rpm (2.9.1) copy them to the places where the spk installed the 2.5.0 files and replace them with the one's from 2.9.1 just look into the "/scripts/postinst" from the spk package ret=`ln -s "${SYNOPKG_PKGDEST}/files/sbin/amsHelper" /sbin/amsHelper` ret=`ln -s "${SYNOPKG_PKGDEST}/modules/$DSM_VERSION/hpilo.ko" /lib/modules/hpilo.ko` ret=`ln -s "${SYNOPKG_PKGDEST}/files/usr/local/etc/rc.d/S99HP-AMS.sh" /usr/local/etc/rc.d/S99HP-AMS.sh` its just the amsHelper and a startspript (made for dsm), youi just have to copy the new amsHelper to /sbin in DSM Quote Link to comment Share on other sites More sharing options...
youhq Posted October 30, 2019 Share #103 Posted October 30, 2019 (edited) I have tested both 1.02b 3615 DSM 6.1.7 and 1.04b 918+ DSM 6.2.2 with good Agentless Management Service (AMS) results. But what I need to mention is that 04-HD Max temperature sensor cannot be recognized through ILO hard driver.thus, the fans cannot adjust the speed automatically. Edited October 30, 2019 by youhq Quote Link to comment Share on other sites More sharing options...
youhq Posted October 30, 2019 Share #104 Posted October 30, 2019 21 hours ago, IG-88 said: its kind of hard to tell what you try to say, did you try both? loader 1.03b with 3615 DSM 6.2.2. loader 1.04b with 918+ DSM 6.2.2 also not sure what you trying to say, you used 3615 dsm 6.2.2 with the original spk? whats 04-hd max? the driver need to be compiled, the spk is a dsm compatible version of what hp released as rpm after installing the spk (2.5.0) i'd expect you extract the files from the rpm (2.9.1) copy them to the places where the spk installed the 2.5.0 files and replace them with the one's from 2.9.1 just look into the "/scripts/postinst" from the spk package ret=`ln -s "${SYNOPKG_PKGDEST}/files/sbin/amsHelper" /sbin/amsHelper` ret=`ln -s "${SYNOPKG_PKGDEST}/modules/$DSM_VERSION/hpilo.ko" /lib/modules/hpilo.ko` ret=`ln -s "${SYNOPKG_PKGDEST}/files/usr/local/etc/rc.d/S99HP-AMS.sh" /usr/local/etc/rc.d/S99HP-AMS.sh` its just the amsHelper and a startspript (made for dsm), youi just have to copy the new amsHelper to /sbin in DSM it does not function with the extracted amsHelper from rpr (2.9.1) amsHelper: error while loading shared libraries: libnl.so.1: cannot open shared object file: No such file or directory Quote Link to comment Share on other sites More sharing options...
IG-88 Posted October 30, 2019 Share #105 Posted October 30, 2019 3 hours ago, youhq said: I have tested both 1.02b 3615 DSM 6.1.7 and 1.04b 918+ DSM 6.2.2 with good Agentless Management Service (AMS) results. But what I need to mention is that 04-HD Max temperature sensor cannot be recognized through ILO hard driver.thus, the fans cannot adjust the speed automatically. thanks i understand it now i looked a little for something like a extra driver but after extending the search i found this (and we need to run in ahci for xpe/dsm, so it seems kind of "normal") This is well known deficiency of MS Gen8. If you use B120i in AHCI mode, iLo is unable to read HD max. If you switch in the BIOS to raid mode - everything will be OK. That is the reason of so called "fan speed issue" with MS Gen 8. Do search of this forum for "fan issue" for more information. Unfortunately HP officially rejected to fix this. They say "this is by design" source: https://homeservershow.com/forums/topic/14953-temp-sensor-04-hd-max/ Quote Link to comment Share on other sites More sharing options...
IG-88 Posted October 30, 2019 Share #106 Posted October 30, 2019 3 hours ago, youhq said: it does not function with the extracted amsHelper from rpr (2.9.1) amsHelper: error while loading shared libraries: libnl.so.1: cannot open shared object file: No such file or directory even if running it might not solve your problem maybe this is the way to go? https://xpenology.com/forum/topic/7691-hp-gen-8-hacked-ilo-and-optimal-bios-settings/ https://www.reddit.com/r/homelab/comments/dc7dbc/silence_of_the_fans_preliminary_success_with/ Quote Link to comment Share on other sites More sharing options...
v02max Posted November 15, 2019 Share #107 Posted November 15, 2019 (edited) So I have got AMS running under "loader 1.04b with 918+ DSM 6.2.2" on ilo 4 2.70 (I don't have a system to test ilo 5 but assume it will work also). Thanks to IG-88 for the complied kernel module hpilo.ko CAUTION... insmod hpilo.ko You need to take the attached zip and unzip it onto /volume1/Downloads or similar directory, DO NOT extract folders into root directories as the /lib is likely to break your install, I have not tested these scenarios... Once extracted you can run it by adding a one time library path to the execution, which will use the attached library files first "under /volume1/Downloads/hp-ams/lib" sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 hp-ams.zip Edited November 15, 2019 by v02max 2 Quote Link to comment Share on other sites More sharing options...
v02max Posted November 17, 2019 Share #108 Posted November 17, 2019 (edited) Here is a working ams as above for "loader 1.03b with 3517 DSM 6.2.2" please extract into /volume1/Downloads/ as above My previous zip contains some excess directories and duplicate library files; I have added the hpilo.ko for 918 / 3157 as labeled (thanks IG-88) this is tested on my Microserver g8 running 2.70 ilo To start, execute: insmod /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 script something like: more /usr/local/etc/rc.d/S99HP-AMS.sh #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 You'll see the below messages on both platforms if it is working, safe to ignore... NET-SNMP version 5.7.3 AgentX subagent connected error: Unable to open /usr/lib/rpm/rpmrc for reading: No such file or directory. Can't find directory of RPM packages System used: Microserver G8 HP Ethernet 1Gb 2-port 361T Adapter1.52, 0x80000fc5, 1.1752.0Slot 1 iLO2.70 May 07 2019System Board Intelligent Platform Abstraction Data0.00System Board Intelligent ProvisioningN/ASystem Board Redundant System ROMJ06 05/21/2018System Board Server Platform Services (SPS) Firmware2.2.0.31.2System Board System Programmable Logic DeviceVersion 0x06System Board System ROMJ06 04/04/2019System Board System ROM Bootblock02/04/2012 hp-ams3517.zip Edited November 17, 2019 by v02max 3 Quote Link to comment Share on other sites More sharing options...
ronron1982 Posted November 22, 2019 Share #109 Posted November 22, 2019 On 11/17/2019 at 5:41 PM, v02max said: Here is a working ams as above for "loader 1.03b with 3517 DSM 6.2.2" please extract into /volume1/Downloads/ as above My previous zip contains some excess directories and duplicate library files; I have added the hpilo.ko for 918 / 3157 as labeled (thanks IG-88) this is tested on my Microserver g8 running 2.70 ilo To start, execute: insmod /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 script something like: more /usr/local/etc/rc.d/S99HP-AMS.sh #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 You'll see the below messages on both platforms if it is working, safe to ignore... NET-SNMP version 5.7.3 AgentX subagent connected error: Unable to open /usr/lib/rpm/rpmrc for reading: No such file or directory. Can't find directory of RPM packages System used: Microserver G8 HP Ethernet 1Gb 2-port 361T Adapter1.52, 0x80000fc5, 1.1752.0Slot 1 iLO2.70 May 07 2019System Board Intelligent Platform Abstraction Data0.00System Board Intelligent ProvisioningN/ASystem Board Redundant System ROMJ06 05/21/2018System Board Server Platform Services (SPS) Firmware2.2.0.31.2System Board System Programmable Logic DeviceVersion 0x06System Board System ROMJ06 04/04/2019System Board System ROM Bootblock02/04/2012 hp-ams3517.zip 4.52 MB · 5 downloads Thanks Bro , I am using 918+ with 1.04b loader (dsm 6.2.2-24922 update 4) , is it safe to use this patch on my gen8 machine ? Quote Link to comment Share on other sites More sharing options...
v02max Posted November 23, 2019 Share #110 Posted November 23, 2019 19 hours ago, ronron1982 said: Thanks Bro , I am using 918+ with 1.04b loader (dsm 6.2.2-24922 update 4) , is it safe to use this patch on my gen8 machine ? That is the setup I have, the main thing is to extract it into your /volume1/ somewhere, not into the root directory "/" if you do this then it is safe, I've just realised I need to cleanup the 918+ zip as there may be excessive files, either way it is safe if used as described. hp-ams.zip Quote Link to comment Share on other sites More sharing options...
ronron1982 Posted November 23, 2019 Share #111 Posted November 23, 2019 4 hours ago, v02max said: That is the setup I have, the main thing is to extract it into your /volume1/ somewhere, not into the root directory "/" if you do this then it is safe, I've just realised I need to cleanup the 918+ zip as there may be excessive files, either way it is safe if used as described. hp-ams.zip 3.53 MB · 1 download Thank you very much !! V02max, Quote Link to comment Share on other sites More sharing options...
ronron1982 Posted November 24, 2019 Share #112 Posted November 24, 2019 (edited) Thanks Again V02MAX, i've got it running well on my baremetal GEN8 System . Also with my (SAS HBA) card. All Drivers both onboard and hba controller are visible. i've tried to follow the instruction and created a task on start up . ---- more /usr/local/etc/rc.d/S99HP-AMS.sh #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 ---- but with no luck , the system reported "file not found "s99hp-ams.sh", somthing like that. then i try: (i replaced the path because i don't want to mess up with my existing folder.) ---- insmod /volume1/hp-ams/hp-ams/hpilo.ko modprobe /volume1/hp-ams/hp-ams/hpilo.ko LD_LIBRARY_PATH=/volume1/hp-ams/hp-ams/lib /volume1/hp-ams/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 ---- it success to run , but i am not sure what "s99hp-ams.sh" is. i don't know what if this file cannot be loaded. by the way, thanks again to V02MAX and everyone . Edited November 24, 2019 by ronron1982 Quote Link to comment Share on other sites More sharing options...
v02max Posted November 24, 2019 Share #113 Posted November 24, 2019 55 minutes ago, ronron1982 said: 55 minutes ago, ronron1982 said: i've tried to follow the instruction and created a task on start up . ---- more /usr/local/etc/rc.d/S99HP-AMS.sh #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 ---- but with no luck , the system reported "file not found "s99hp-ams.sh", somthing like that. then i try: (i replaced the path because i don't want to mess up with my existing folder.) ---- insmod /volume1/hp-ams/hp-ams/hpilo.ko modprobe /volume1/hp-ams/hp-ams/hpilo.ko LD_LIBRARY_PATH=/volume1/hp-ams/hp-ams/lib /volume1/hp-ams/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 ---- it success to run , but i am not sure what "s99hp-ams.sh" is. i don't know what if this file cannot be loaded. by the way, thanks again to V02MAX and everyone . /usr/local/etc/rc.d/ is where you place the startup scripts so you need to create the S99HP-AMS.sh in that directory copy the below to your buffer #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 then do sudo vi /usr/local/etc/rc.d/S99HP-AMS.sh then press "SHIFT i" for insert and paste it into the file #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 then press ESC type the below to exit and save the file :wq! then type "sudo chmod 755 /usr/local/etc/rc.d/S99HP-AMS.sh" upon reboot it should run automatically 1 Quote Link to comment Share on other sites More sharing options...
ronron1982 Posted November 24, 2019 Share #114 Posted November 24, 2019 24 minutes ago, v02max said: /usr/local/etc/rc.d/ is where you place the startup scripts so you need to create the S99HP-AMS.sh in that directory copy the below to your buffer #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 then do sudo vi /usr/local/etc/rc.d/S99HP-AMS.sh then press "SHIFT i" for insert and paste it into the file #!/bin/sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH=/volume1/Downloads/hp-ams/lib /volume1/Downloads/hp-ams/sbin/amsHelper -f -I0 -M1,5,14,16,18,23,99 then press ESC type the below to exit and save the file :wq! then type "sudo chmod 755 /usr/local/etc/rc.d/S99HP-AMS.sh" upon reboot it should run automatically Oh yeah , thanks so much Bro . Quote Link to comment Share on other sites More sharing options...
cpuks Posted November 25, 2019 Share #115 Posted November 25, 2019 Does it helps somehow with high fan speed with AHCI turned on? Quote Link to comment Share on other sites More sharing options...
v02max Posted November 26, 2019 Share #116 Posted November 26, 2019 2 hours ago, cpuks said: Does it helps somehow with high fan speed with AHCI turned on? Doubt it, if there is a fix for that would more likely be in the bios, ilo revisions. This will work with the latest revisions.. Quote Link to comment Share on other sites More sharing options...
youhq Posted December 8, 2019 Share #117 Posted December 8, 2019 On 2019/11/24 at PM1点58分, ronron1982 said: 再次感谢V02MAX,我已经在裸机GEN8系统上很好地运行了它。 也可以使用我的(SAS HBA)卡。板载和hba控制器上的所有驱动程序均可见。 我试图按照说明进行操作,并在启动时创建了任务。 ---- 更多/usr/local/etc/rc.d/S99HP-AMS.sh#!/ bin / sh modprobe /volume1/Downloads/hp-ams/hpilo.ko sudo LD_LIBRARY_PATH = / volume1 / Downloads / hp-ams / lib /第1卷/下载量/ hp-ams / sbin / amsHelper -f -I0 -M1,5,14,16,18,23,99 ---- 但是没有运气,系统报告“找不到文件“ s99hp-ams.sh””,像这样。 然后我尝试:(我替换了路径,因为我不想弄乱我现有的文件夹。) ---- insmod /volume1/hp-ams/hp-ams/hpilo.ko modprobe /volume1/hp-ams/hp-ams/hpilo.ko LD_LIBRARY_PATH = / volume1 / hp-ams / hp-ams / lib / volume1 / hp-ams / hp-ams / sbin / amsHelper -f -I0 -M1,5,14,16,18,23,99 ---- 它运行成功,但是我不确定“ s99hp-ams.sh”是什么。 我不知道该文件无法加载怎么办。 顺便说一句,再次感谢V02MAX和大家。 04-HD Max ok?I tried again,but still no success ml310e gen8 v2 918+ 1.04b loader dsm 6.2.2-24922 update 4 Quote Link to comment Share on other sites More sharing options...
nikon331 Posted January 25, 2020 Share #118 Posted January 25, 2020 I wish someone would do a easy tutorial or perhaps a video on how to apply this patch to Xpenology for AMS support on the Gen8 Microserver I know this is an old topic but I’m not very familiar with Linux commands but would like to get this working on my box. Quote Link to comment Share on other sites More sharing options...
Last Boyscout Posted February 22, 2020 Share #119 Posted February 22, 2020 On 11/17/2019 at 10:41 AM, v02max said: Here is a working ams as above for "loader 1.03b with 3517 DSM 6.2.2" please extract into /volume1/Downloads/ as above Thanks V02max; It worked for me as well on my Gen8 (Latest Ilo f/w, HP Bios and DSM 6.2.2-24922 Update 4). Now all we need to have someone to create an SPK of it so others can benefit from it without tinkering Quote Link to comment Share on other sites More sharing options...
Ionlab Posted May 15, 2020 Share #120 Posted May 15, 2020 (edited) Hi, I seem to have some trouble getting the thing to work. I downloaded the hp-ams files from this post I have copied the hp-ams directory to /volume1/Downloads/ retaining the zip structure I am using the hpilo.ko as is (not the 918 nor the 3617 variant) I have created the script as indicated at /usr/local/etc/rc.d Whenever I try to run it (via ssh after logging in as admin and typing sudo su) I get the following response "This program requires the host to have a HP Integrated Lights Out 4 (iLO 4) BMC" This happened with ILO 2.60, 2.61b, and now the latest 2.73 What am I doing wrong? Setup is Baremetal Gen8/G1610T 3615xs/Jun's mod 1.03b/DSM 6.2-23739 Update 2 Edited May 15, 2020 by Ionlab Quote Link to comment Share on other sites More sharing options...
Ionlab Posted May 16, 2020 Share #121 Posted May 16, 2020 OK...The spk package did the job wonderfully!!! Seems I mixed up the DSM versions!!! Quote Link to comment Share on other sites More sharing options...
Ionlab Posted May 16, 2020 Share #122 Posted May 16, 2020 FYI the 4sag package also Works with DSM 6.2.3-25426 Quote Link to comment Share on other sites More sharing options...
le.pipo007 Posted May 28, 2020 Author Share #123 Posted May 28, 2020 On 5/16/2020 at 7:21 PM, Ionlab said: FYI the 4sag package also Works with DSM 6.2.3-25426 hi i don't understand, you download this file? https://spk.4sag.ru/packages/hp_ams-5.2_2.5.0-1.spk for me, it not starting! how can you do that? Quote Link to comment Share on other sites More sharing options...
Ionlab Posted May 28, 2020 Share #124 Posted May 28, 2020 30 minutes ago, le.pipo007 said: hi i don't understand, you download this file? https://spk.4sag.ru/packages/hp_ams-5.2_2.5.0-1.spk for me, it not starting! how can you do that? I added the 4sag.ru repository to my package center. Afterwards you search for the hp-ams package and install it and reboot. Alternatively you can downloaded the file and install it using the manual install in the package center. After the reboot everything was running. If the link is not working for you attached is the spk file. hp_ams-5.2_2.5.0-1.spk 1 Quote Link to comment Share on other sites More sharing options...
le.pipo007 Posted May 28, 2020 Author Share #125 Posted May 28, 2020 ok, thanks, i try to launch it, without reboot ! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.