Aigor Posted December 10, 2016 Share #1 Posted December 10, 2016 (edited) Hi friends, i have one Gen8 box with dsm 6.02 with last Jun bootloader, i add a 10 Gb SFP intel network card and try to configure iSCSI to host a datastore for my esxi box. Everything seems ok, but despite card have static ip and webinterface showme connect at 10 Gb FD i can't ping vmware host and from vmware i can't ping synology box, i'm still crazy , i'm not able to target the problem, everything seems work fine but i can't add iSCSI target. Many thanks Edited February 17, 2017 by Guest Link to comment Share on other sites More sharing options...
Polanskiman Posted December 12, 2016 Share #2 Posted December 12, 2016 I am not using VM, I am on baremetal, but I remember I had some issues in the past when I tried to ping the NAS. I solved it by adding an ICMP rule in DSM firewall which explicitly allowed DSM to respond to ping requests. Try that and let me know if it works for you. Link to comment Share on other sites More sharing options...
Aigor Posted December 12, 2016 Author Share #3 Posted December 12, 2016 I am not using VM, I am on baremetal, but I remember I had some issues in the past when I tried to ping the NAS. I solved it by adding an ICMP rule in DSM firewall which explicitly allowed DSM to respond to ping requests. Try that and let me know if it works for you. Hi, i'm using baremetal too, i have one esxi host and one gen8 box with xpenology installed, all works fine. So i decide to play with 10Gb nic card to use iSCSI as storage for esxi host, i bought 3 cards, one dual port to install on xpenology, and other two for my desktop pc and my esxi host. I don't have any switches, i connect esxi 10Gb card directly with one port on dual port card in xpenology, defined iSCSI lun and target, assigned ip on same class on both hosts ( xpenology and esxi) try to ping frome one to each other, no ping response, both webinterface show me card connected, so i assume both are working, tcpdump on xpenology on 10Gb card, show me no packet comes from somewhere when ping from esxi to xpenology, networking are up and running. I suspect there is some trick on synology because i have the same problem if i connect my desktop pc with xpenology via 10gb card. As far you know there is some bond beetwein number of physical cards and boot argument if_number=(number of card ) ? After my regular work i will try to figure what's wrong, but i suspect is boot arg if_number Many thanks for the answer. Link to comment Share on other sites More sharing options...
peterpakos Posted February 3, 2017 Share #4 Posted February 3, 2017 Aigor, did you manage to get to the bottom of this? I think I'm experiencing exactly the same issue with HP NC365T card I added to my HP Microserver running DSM 6.0.2. Link to comment Share on other sites More sharing options...
Aigor Posted February 17, 2017 Author Share #5 Posted February 17, 2017 Aigor, did you manage to get to the bottom of this? I think I'm experiencing exactly the same issue with HP NC365T card I added to my HP Microserver running DSM 6.0.2. yes and not. Digging into boot log i catch this errors [ 15.985894] ixgbe 0000:07:00.0: SR-IOV: bus number out of range [ 15.988036] ixgbe 0000:07:00.0 (unregistered net_device): Failed to enable PCI sriov: -12 [ 16.162859] ixgbe 0000:07:00.1: SR-IOV: bus number out of range [ 16.164981] ixgbe 0000:07:00.1 (unregistered net_device): Failed to enable PCI sriov: -12 [ 21.064691] BTRFS: has skinny extents It seems it's' a SR-IOV probolem. Looking for error in google, i found a trick, i have to load ixgbe module with max_vfs=8 param, but this param it's already present in /etc/modules_conf. Unload ixgbe and load without any param, did trick, but evene if commented out param in modules_conf, it seems that module still loading at boot time with param, the only way to work with intel dual 10Gb card, it's' unload module, reload whitout any params, and restart networking,after this trick 10Gb card start to working well. I would like to avoid any param to be passed to module, but i don'know where looking for, using modules_conf like in any other distro, don't do the magic If you have some idea Link to comment Share on other sites More sharing options...
Aigor Posted February 17, 2017 Author Share #6 Posted February 17, 2017 Solved i had to edited /etc.defaults/modules.conf , deleted max_vfs param my card it's working Link to comment Share on other sites More sharing options...
peterpakos Posted February 22, 2017 Share #7 Posted February 22, 2017 Many thanks! Link to comment Share on other sites More sharing options...
peterpakos Posted February 26, 2017 Share #8 Posted February 26, 2017 Solved i had to edited /etc.defaults/modules.conf , deleted max_vfs param my card it's working Can you tell me what exactly you have got in /etc.defaults/modules.conf? Or is it /etc/modules.conf that needs to be updated? I've just installed Intel x520 card and cannot ping its IP address despite the link being up. Many thanks. Link to comment Share on other sites More sharing options...
s3ntro Posted March 1, 2017 Share #9 Posted March 1, 2017 I just installed an Intel x540-T2 and after assigning manual IP addresses (separate networks for each port going to two different computers) I have the same issue. Link is up and recognized as 10G but no communication is happening. I don't know the first thing about editing or compiling kernel stuff. Is there anything I can do? 6.0.2-8451 update 8. Bare metal. Edit: damn it I'm the FNG replying to a solved thread. Link to comment Share on other sites More sharing options...
Recommended Posts