Jump to content
XPEnology Community

Dominik

Rookie
 View Profile  See their activity

  • Posts

    9

  • Joined

  • Last visited

 Content Type 

Posts posted by Dominik

    TinyCore RedPill Loader (TCRP)

    in Loaders

    Posted · Edited by Dominik

    16 minutes ago, pocopico said:

     

    Unfortunatelly there is always the chance to get an early KP and if this will stops the boot process the diag will not run.  Try with a different loader. DS3266 is always IMHO the best option ATM 

    Yes, i think so too. But i`ve tried so many variants of different loaders for all supported DS (uefi and bios), that i`ll wait for a new kernel / image like 0.4.7 or higher.. Do you have some plans for updates? Like, to support for dsm 7.1?

     

    Dominik

    TinyCore RedPill Loader (TCRP)

    in Loaders

    Posted · Edited by Dominik

    16 minutes ago, pocopico said:


    you have to leave the boot to complete. After the collection is triggered it will take about 120 secs before it’s launched. So leave it for about 5 minutes after you edit grub and boot. You will find the file under /mnt/sda3/diag folder 

    Hi @pocopico

     

    Sry, but there is no such diag folder.. I leave the boot for 10 minutes and the message "starting kernel with usb boot" is displayed, but still no data.. Should there be more information on screen? How can i check, that the boot has been done? I guess, i have a boot-problem, the kernel can`t fully boot and that is the reason, i don`t get a dhcp adress... Btw, there are no build errors, anything is green and i tried different usb sticks.

     

    Dominik

    TinyCore RedPill Loader (TCRP)

    in Loaders

    Posted · Edited by Dominik

    27 minutes ago, pocopico said:

     

    Its an extension, you have to add it as you do with any extension before you build the loader.

    Hi @pocopico Thank you for your respond and information. I`ve successfully added the extension with sudo ./rploader.sh ext broadwellnk-7.0.1-42218 add https://raw.githubusercontent.com/pocopico/rp-ext/main/tcrp-diag/rpext-index.json and build the uefi-loader 0.4.6 for DS3622xs+ after that. Unfortunately, i still don`t get any diagnostic data, when i add the tcrpdiag command in grup with "e".. Any further suggestions/solutions..? I Can`t telnet/ssh, because i don`t get an ip-address and that`s the reason for needing some disgnostic data.

     

    Sry, i`m a beginner in grub/linux and xpenology, i hope, you can help me.

     

    Dominik

    TinyCore RedPill Loader (TCRP)

    in Loaders

    Posted · Edited by Dominik

    11 hours ago, painkiller895 said:

    Plug in a intel nic card  Then build your loader.  it should work  Do not use internal card...

     

    Hi @painkiller895

     

    Thank you for your respond and interest. I installed a separate intel nic and tested all the bios and uefi  0.4.6 variants with DSM 7.0.1 of the tinycore/redpill loader but i can`t still not get any dhcp adress or access to the DSM setup homepage.

     

    @pocopico I`ve tried to setup your tcrpdiag command in GRUB  to give me a hint, what the reason is, but unfortunately, i can`t get some disgnostic data. there ist nothing stored on my usb bootstick, in any folders of all partitions.. Do i have to setup this tcrpdiag command in the build command or can i place it normally with "e" in the GRUB boot screen so i can get some additional data for further research?

     

    Thank you for your answers!

     

    Dominik

    TinyCore RedPill Loader (TCRP)

    in Loaders

    Posted · Edited by Dominik

    3 hours ago, Aigor said:

    I have same hardware and i was able to update from 6.2.3 to 7.01 
    how loader has been built? 
    if you used tinycore, you have to add TG3 extension on building and you have to use DS3622xs+ hardware 
    Try install without ANY other network card than internals 

    Gen8 doesn't have UEFI bios so can't boot UEFI loader 

     

    Hi @Aigor

     

    Thank you for your answer. To be clear, i don`t use an HP microserver, i`m using an amd mainboard, an asrock x570 phantom gaming 4. I used the DS3622xs+ variant with uefi and bios. I included also the TG3, e1000, e1000e and i40e driver. Unfortunately, this didn`t help me. It seems, that i`m still not getting any dhcp adress... It still stucks at "starting kernel with usb boot" and i`m not able to find the ds over find.synology.com and the synology assistant. I tried it with the buildin nic (intel i211at) and removed the atlantic nic, but no success. Any other suggestions..? From anyone..?

     

    Greetings Dominik

    TinyCore RedPill Loader (TCRP)

    in Loaders

    Posted

    2 hours ago, cospotato said:

    Hello @pocopico@Aigor,

     

    My server is microserver Gen8. I followed this https://xpenology.club/install-dsm-7-on-baremetal-or-vm/ tutorial tried again and again. But after reboot. The Server stuck at this screen. And never fetch IP from my DHCP Server. Please help!

    image.thumb.png.e79a9724136da038fa5fc397d067dce0.png

     

    I also fetched the console output with iLO VSP

    console.log 25.81 kB · 1 download

     

     

    Hello @ all

     

    I`ve got the same problem like cospotato. I`m running the tinycore/redpill 0.4.6 version with an amd x570 board and an atlantic 10gb card and an onboard intel 221 1gb nic. I`ve tried it in uefi and bios mode, but i can`t get it to work. it seems, it doesn`t get an ip adress in any way with the atlantic or the intel nic. Please help!

     

    Greetings Dominik

×
×
  • Create New...