Search the Community

Hi everyone! This is my first post on this forum. I made an Xpenology NAS from my old DELL T40 computer with an H310 controller in IT mode, 8x 2TB HDD. In this DELL I have an ASUS XG-C100C 10gbps network card. Unfortunately, Xpenology does not recognize this card. What drivers do I need to install for Xpenology to see this card? Do I have to reinstall the system or is it possible to install drivers for this card? SYSTEM: DSM 7.1.1-42962 Update 6 DEVICE: DS3622xs+ I installed Xpenology from the arpl-1.1-beta2a.img image Thanks!

Hi. curious about the article https://servicemax.com.au/tips/synology-10gigabit-ethernet-on-the-cheap/ I purchased an Asus 10GBe rj45 card. I am encountering an error when executing instructions in ssh: /usr/local/etc/rc.d/aqc107.sh start installing config removing synology kernel driver rmmod: ERROR: Module atlantic is not currently loaded installing proper module from /volume1/aqcnetconf/atlantic.ko insmod: ERROR: could not insert module /volume1/aqcnetconf/atlantic.ko: Invalid module format restarting networking, dont panic /etc/rc.network: line 1194: nat_stop_dhcpd: command not found [dhclient@eth0.service] stopped. [dhclient6@eth0-client.service] stopped. [dhclient6@eth0-info.service] stopped. [dhclient6@eth0-pd.service] stopped. [dhclient@eth1.service] stopped. [dhclient6@eth1-client.service] stopped. [dhclient6@eth1-info.service] stopped. [dhclient6@eth1-pd.service] stopped. [dhclient@eth2.service] stopped. [dhclient6@eth2-client.service] stopped. [dhclient6@eth2-info.service] stopped. [dhclient6@eth2-pd.service] stopped. [dhclient@lo.service] stopped. [dhclient6@lo-client.service] stopped. [dhclient6@lo-info.service] stopped. [dhclient6@lo-pd.service] stopped. [dhclient@tun.service] stopped. [dhclient6@tun-client.service] stopped. [dhclient6@tun-info.service] stopped. [dhclient6@tun-pd.service] stopped. eth1: ERROR while getting interface flags: No such device eth2: ERROR while getting interface flags: No such device tun: ERROR while getting interface flags: No such device 0 0 0 0 unknown Finally, it only loads my built-in network card. Is Xpenology in DSM7 not possible to install this card?

Hello! I've finally get a DSM 7.1.0-42661 working on my test system (i7-4770, rtl8111, Intel 8 Series C220 chipset). Now I'm trying to add a NIC Asus XG-C100C that is identified by TCRP as Aquantia Corp. AQC113CS NBase-T/IEEE 802.3bz Ethernet Controller [AQtion] [1d6a:94c0] The problem is if I add the atlantic module the installation always ended on a loop install. I've suppose that the driver is not valid for that NIC because his ID or the chipset itself is sensible different from is included on the rpext repo (which always reference to AQC107/8 but no AQC113CS). I've found the linux driver on the Asus website for this NIC, but I don't have any idea how can make it myself, in which distro linux could I make it or how compile to test it later on DSM 7, replacing the included atlantic.ko file, I'm totally newbie with these questions compilation related. Can somebody give me some basic instructions to start with? Thanks in advance.

ASROCK Z370 GAMING K6 INTEL INTEL CORE I3-8100 CRUCIAL 8GB 2X4 D4 2400 SPLT CL16 10 randoms HDDs = SHR = 20TB XPEnology runs pretty great! Ended up with a DS-3615xs running 6.1.6-15266 Turned on SHR because the drives are all different sized repurposed HDDs. I installed an ASUS XG-c100c. The module shows up in lspci -vvv: admin@salt:**/**$ lspci -d 1d6a:d107 -vvv 0000:06:00.0 Class 0200: Device 1d6a:d107 (rev 02) Subsystem: Device 1043:8741 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at fd840000 (64-bit, non-prefetchable) Region 2: Memory at fd850000 (64-bit, non-prefetchable) Region 4: Memory at fd400000 (64-bit, non-prefetchable) Expansion ROM at fd800000 [disabled] Capabilities: <access denied> Kernel driver in use: atlantic but when I look in DSM > Networking > Network Interface > LAN 2 "Disconnected" and the Network Status is "--" I have link lights and a "CAT7" cable between the computers. The other end of the link is a CentOS 7.4 server. If I ifconfig down the interface, the link lights go out. When I up the interface the lights come on. I could do this all day. What am I doing wrong? I edited the grub.conf with my mac addresses and changed the nic count to 3. I've played with changing round the order of the MAC addresses BUT I CAN'T BRING THE 10g INTERFACE UP! Help?

habe auf den englischen Forum-Seiten etwas gefunden, siehe Link; werde aber nicht schlau aus der Info. Kann mir jemand helfen was ich für ein Kunststück man machen muss damit die ASUS Karte zum laufen kommt. Weitere Frage eine Original Syno Karte E10G18-T1 würde etwas das doppelte der ASUS kosten, würde diese wenigsten ohne Bastelei auf einem Clon laufen? Bsp ds3617 https://xpenology.com/forum/search/?&amp;q=ASUS XG-C100C &amp;search_and_or=or&amp;sortby=relevancy

I'm running an ASUS mobo with an AMD PHENOM II 4 core, 16GB RAM, 8 HDDs. XPEnology runs pretty great! Ended up with a DS-3615xs running 6.1.6-15266 Turned on SHR because the drives are all different sized repurposed HDDs. All that is awesome, however, I still have a couple of issues. 1. dmesg shows this pretty early in the bootup. DSM shows 4GB RAM, 12GB is "reserved" WARNING: BIOS bug: CPU MTRRs don't cover all of memory, losing 12799MB of RAM. 2. My 2nd nic is a xg-c100c. The module shows up in lspci -vvv: 0000:06:00.0 Class 0200: Device 1d6a:d107 (rev 02) Subsystem: Device 1043:8741 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at fd840000 (64-bit, non-prefetchable) Region 2: Memory at fd850000 (64-bit, non-prefetchable) Region 4: Memory at fd400000 (64-bit, non-prefetchable) Expansion ROM at fd800000 [disabled] Capabilities: [40] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L0s L1, Exit Latency L0s unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] MSI-X: Enable+ Count=32 Masked- Vector table: BAR=2 offset=00000000 PBA: BAR=2 offset=00000200 Capabilities: [a0] MSI: Enable- Count=1/32 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [c0] Vital Product Data Product Name: AQtion Read-only fields: [PN] Part number: AquantiaPartNumber [EC] Engineering changes: AquantiaEngineeringChangeLevel [FG] Unknown: 41 71 75 61 6e 74 69 61 46 61 62 72 69 63 47 65 6f 67 72 61 70 68 79 [LC] Unknown: 41 71 75 61 6e 74 69 61 4c 6f 63 61 74 69 6f 6e [MN] Manufacture ID: 41 71 75 61 6e 74 69 61 4d 61 6e 75 66 61 63 74 75 72 69 6e 67 49 64 [PG] Unknown: 41 71 75 61 6e 74 69 61 50 63 69 47 65 6f 67 72 61 70 68 79 [SN] Serial number: AquantiaSerialNumber [V0] Vendor specific: AquantiaVendorSpecificReadOnlyItem0 [V1] Vendor specific: AquantiaVendorSpecificReadOnlyItem1 [RV] Reserved: checksum good, 0 byte(s) reserved Read/write fields: [YA] Asset tag: AquantiaAssetTagIdentifier [V0] Vendor specific: AquantiaVendorSpecificWritableItem0 [V1] Vendor specific: AquantiaVendorSpecificWritableItem1 [Y0] System specific: AquantiaSystemSpecificWritableItem0 [Y1] System specific: AquantiaSystemSpecificWritableItem1 [RW] Read-write area: 9 byte(s) free End Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [150 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Capabilities: [180 v1] #19 Kernel driver in use: atlantic but when I look in DSM > Networking > Network Interface > LAN 2 "Disconnected" and the Network Status is "--" I have link lights and a "CAT7" cable between the computers. The other end of the link is a CentOS 7.4 server. If I ifconfig down the interface, the link lights go out. When I up the interface the lights come on. I could do this all day. What am I doing wrong? I edited the grub.conf with my mac addresses and changed the nic count to 2. Help?