-
Posts
583 -
Joined
-
Last visited
-
Days Won
7
Posts posted by Trantor
-
-
Marvell SE9172+Intel C2750 SATA3 Don't Mix. But they Did all work in Nanoboot.
So to sume up, when I enable Marvell SE9172 and the two SATA3 ports on the Intel C2750 Controller at the same time, I get this boot hang issue "=trigger device plug event="
Hope this helps.
First thanks you and neoeny152 for these feedbacks.
Which version of Nanoboot it is ? Did it works with eveything in AHCI mode and all controllers enabled?
-
I have the C2750D4I MB.
I have the same issue. The Intel and Marvell SE9230 ports are working, in IDE aswell as AHCI mode. But when I enable the Marvell SE9172, I get =trigger device plug event= when trying boot. This is only 2x sata, so not such a big issue for me.
So it lookslike there are an issue with the Marvell SE9172 drivers.
I'm running 5.2-5592.2
Thank's for the great work!!!
Thank's for this feedback.
I read some informations about this issue here : viewtopic.php?f=2&t=5203&start=10
Some users disable marvell controllers, some switch intel and marvell to IDE and other disable COM ports...
Asrock C2750D4I --> "Intel RC Setup -> South Bridge Chipset Configuration -> SATA Configuration -> SATA Mode Selection = IDE"
Can you please confirm that you can boot and use intel and marvell 9230 in AHCI mode without any issue.
If it's ok try to disable everything exept marvell 9172 controller and do to some tests in both mode (AHCI & IDE) to confirm the issue.
This will maybe help us to find a fix to this boot hang issue
-
Hello, I'm not really sure how to go about this or if this has already been requested. But is it possible to add support for this ASRock motherboard (see below) - So that it can be run outside of 'ide mode' (ahci mode). Because of having to run in IDE mode I lose several SATA ports that the board comes with and I'm considering adding more hard drives soon. Hopefully this request is in the right place.
ASRock Intel Avoton C2750 2.4GHz/DDR3/SATA3/V&2GbE/Mini-ITX Motherboard and CPU Combo C2750D4I
http://www.asrockrack.com/general/produ ... I#Download
-NeoenY152
I already read something similar about switching from AHCI to IDE in the forum.
Can you explain what happen exactly in both mode with maximum details.
EDIT:
After reading motherboard manual I see 12 SATA ports handle by two controllers:
Intel : 2 x SATA3 6.0 Gb/s, 4 x SATA2 3.0 Gb/s
Additional SATA
- Marvell SE9172: 2 x SATA3 6.0 Gb/s, support RAID 0, 1
- Marvell SE9230: 4 x SATA3 6.0 Gb/s, support RAID 0, 1,
Which SATA ports are working and which doesn't ?
-
Hi, is there anyway to add Dell R610 NIC drivers? I believe its the Broadcom BCM5709C not too positive... even after trying 5644 I receive eth0/1/2/3 are not up. Thanks
I made a mistake and put the missing firmware in /lib/firmware/bnx2x/ instead of /lib/firmware/bnx2/
You have to move the file bnx2-mips-09-6.2.1b.fw from bnx2x to bnx2 folder.
This will be fix the next repack/release.
-
In the syslinux.cfg located on your usb stick you can edit the network interface number :
netif_num=4 to netif_num=X
Other users with mellanox have to switch port type form ib to eth:
https://community.mellanox.com/docs/DOC-1131
look the inbox driver part
-
It's a know issue with Broadcom NetXtreme II 5709c network adapter. (missing firmware)
viewtopic.php?f=2&t=1361&start=590
This will be included in the next release
-
guys, can you please open a new thread about your dvb issues.
-
@dszego : Fist thank you for your work.
Can you please open a new thread for this subject.
In your package make some cleaning in order to only have modules related to media and not all kernel modules
According to your script you only need :
"media.ko videodev.ko dvb-core.ko dvb_pll.ko cx88-vp3054-i2c.ko videobuf-dma-sg.ko videobuf-core.ko videobuf-dvb.ko btcx-risc.ko tveeprom.ko v4l2-common.ko rc-core.ko videobuf-dma-sg.ko tda8290.ko tuner.ko tuner-types.ko tuner-simple.ko cx88xx.ko cx8800.ko cx8802.ko or51132.ko cx88-dvb.ko"
and of course firmwares
EDIT: backports_dvb modules are not loaded by your script.
-
Thus, the request to add the driver "pata_via.ko" to the next release XPEnology. I do not know whether to write to Sancome whether it is your part in the project, ie. drivers.
pata_via and other requested drivers (i40e, usb-lan...) will be added to the next release.
Promise FastTrak TX4650, 4SATA RAID CARDI will check this
-
Server HP Enterprise ProLiant ML10 v2 G3240 4GB-U B120i
Drivers for intel X710-DA2;
DSM 5.2-5592 DS3615xs update 4
XPEnoboot DS3615xs 5.2-5592.2
the network card is not detected.
Thanks a lot.
Your network card is handled by the intel i40e driver : https://downloadcenter.intel.com/downlo ... der-Linux-
It's not included but I will try to find some time to compil it
EDIT : Here the i40e driver https://download.xpenology.fr/drivers/i40e.ko
-
Look here for 2680 : viewtopic.php?f=2&t=1361&start=620#p45107
Here for 271x/272x : viewtopic.php?f=2&t=1361&hilit=rocketraid&start=580#p42804
Here for 620/622/640/644/640L/642L/644L/RR644LS : viewtopic.php?f=2&t=7737&p=43301&hilit=rocketraid#p43301
-
I'm having a lot of trouble getting this one compiled
http://www.highpoint-tech.com/BIOS_Driv ... _24.tar.gz
downloaded the source and toolchain and make cross_compile=toolchain kerneldir=source/linux-3.10.x
but nothing happens, i think there might be something wrong with the driver package, but i could be doing something really stupid.
if anybody has some tips or a vm to cross compile for 5.2 that would be great
Here the rr2680 drivers : https://download.xpenology.fr/drivers/rr2680.ko
Same warning has before (viewtopic.php?f=2&t=1361&hilit=rocketraid&start=580#p42804), unload mvsas module before loading rr2680.ko !
-
Just did some additional test on my asus a8n-e with these graphic cards : Quadro FX, 8600GT, 9800GT, HD5450.
All cards boot ok up to the login prompt without doing anything.
I don't think it's something about the graphic cards but maybe it's related to gigabytes mainboard.
Gigabyte EP45-DS3 : vigao
Gigabyte GA-X99-UD4 : xpenfan
Gigabyte 965P-DS4 : zslibra
Gigabyte Ga-965P-DS3 : mats92
-
Only the 1 Gigabit port with Realtek RTL8153 remains unrecognized.
Check this post for Realtek RT8153 : viewtopic.php?f=2&t=5260#p42803
-
When it shows you the booting kernel screen, did you have a blinking cursor or anything else ?
Did you check if synology assistant detect your system ?
-
Hi Trantor.
thank you for your response. I am quite a newbie with linux commands. Can you detail exactly how to use the lsmod commands?
Also, any ideas about the "system partition failed" errors ? all my drives were fine until I tried the inifiniband drivers
Enable SSH in DSM option, download putty, connect to your XPEnology with user root and your admin password.
type : insmod /lib/modules/e1000e.ko and insmod /lib/modules/igb.ko
It should load intel drivers (if they are not already loaded).
Sorry but no ideas about your system partiton failed
-
Did you try to add nomodeset parameter to grub ?
When booting press tab to edit the boot command line:
edit : APPEND root=/dev/md0 ihd_num=0 netif_num=4 syno_hw_version=DS3615xs sn=B3J4N01003 vid=0x0EA0 pid=0x2168 loglevel=0 vga=0x305
to : APPEND root=/dev/md0 ihd_num=0 netif_num=4 syno_hw_version=DS3615xs sn=B3J4N01003 vid=0x0EA0 pid=0x2168 loglevel=0 nomodeset
You can also edit syslinux.cfg
-
I just tried an old computer with an asus a8n-e and nvidia 8400gs.
No blank screen issue.
Did you tried to boot in debug mode ?
In DSM 5.1 use lspci -qk command to show informations about pci.
If lspci command is not present boot a linux livecd like ubuntu and use lspci -qk
In 5.2 with the 8400GS I have:
DiskStation> lspci -qk 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [GeForce 8400 GS] (rev a1) Subsystem: Gigabyte Technology Co., Ltd Device 3463
-
Hi Trantor,
Could you please include the tun kernel module in XPEnoboot? I got ZeroTier One to install and run, but without that kernel module its a little useless
Also, are the sources for XPEnoboot available for our own tinkering? ... as per GPL?
Thanks
tun module is included but not loaded. You only need to insmod it
-
Does that mean an updated image is upcoming?
Also, seeing that 5.1 does work for me, does it ultimately mean that whatever was included in 5.1, was removed in 5.2?
Thanks Trantor.
When Synology release DSM 5.2 they update the linux kernel to 3.10.35 so every parameters have to be set again and kernel have to be patched and recompiled.
I plan to make a thread with a todo list so the dev team know what to fix/update.
I hope this will help this project to go forward
No idea about an upcoming release.
-
Another diffrenece is that GnoBoot found file "pata_via.ko" , wchich XPEnology didn't found. Any suggestions what to check next?
Module size is not relevant because 5.1 modules use kernel 3.2.40 and 5.2 use 3.10.35.
I think you found the source for your issue. Maybe VX900 support is not in sata_via but in pata_via.
I will try to find some time to compil it
EDIT : Here https://download.xpenology.fr/drivers/pata_via.ko
Copy it to /lib/modules/ and insmod it.
I'm afraid that if it detect your drive it didn't survive a reboot...
-
To sum up external graphics = blank screen and onboard graphic = good ?
If so It seems to me that the kernel is missing some part for display support.
Is there anything I could try/do with the img/iso to make 5.2 work?
Unfortunately no. The dev team have recompil kernel with more graphics support.
-
To sum up external graphics = blank screen and onboard graphic = good ?
If so It seems to me that the kernel is missing some part for display support.
-
Hi Trantor, would help add or explain how to add support for SATA for the VIA VX900 chipset for XPEnology. I am currently working on GnoBoot 10.5. I could not run Synology or on Nanoboot or also XPEnoboot in any version. It did not detect HDD. I work on HP Thin Client T5550 / T5565. Regards.
When you use XPEnoboot bootloader did you find your system with Synology Assistant ? If yes it's says NO HDD ?
VIA VX900 is handle by sata_via which is included and the lan part by via-velocity which is included (but not loaded in my VM setup).
How about a wiki of compatible hardware
in Archives
Posted
Your answer is in the sentence :
add rmmod=r8169 to grub or syslinux.cfg in order to unload r8169 driver and force r8168.
Linux Realtek drivers are shit
The old shitty r8169 driver from the kernel will be removed and replaced by the "new" r8169 from realtek web site in the next release.