SSS_Viva
-
Posts
32 -
Joined
-
Last visited
Everything posted by SSS_Viva
-
Received USB DOM, the installation was successful. Next CPU 🤪.
- 306 replies
-
- 1
-
-
- firmware
- 08-0220usb14
- (and 4 more)
-
Did you have to replace the connector?
-
Phison String Info updater can change the appearance of VID PID. click
-
I have not yet seen in any of the bootloaders that the search for the necessary files would occur by VID PID, either the UUID of the partition is registered in the config, or, as in this case, HD0, which will be the USB connector for the USB DOM. In this case, there are two options, either to change the config to boot by UUID, or to solder a regular USB connector to the USB DOM connector.
- 306 replies
-
- 1
-
-
- firmware
- 08-0220usb14
- (and 4 more)
-
your NAS is configured to boot from HD0, it is possible that HD0 is a USB DOM, and from another device, it will not be possible to boot in a simple way, you have to wait for a new USB DOM.
-
On the first section, there is a file called SynoBootLoader.conf ? Can you show its contents?
-
Remove the USB DOM. Take any usb flash drive, deploy the resulting image from the USB DOM to it, Insert into the front USB and try to boot.
-
I wrote above that this utility only works under Windows XP 32, tested personally.
-
https://xpenology.com/forum/topic/9897-flash-transplant/ In this message there is a utility to change the VID PID, but for me, it only worked under Windows XP 32bit.
-
My Putty also gave out unacceptable data, I used this program, everything is displayed correctly in it.
-
Apparently we don't understand each other.
- 306 replies
-
- 1
-
-
- firmware
- 08-0220usb14
- (and 4 more)
-
What did I say wrong? The 412+ has an Intel Atom D2700 processor and is not affected by the AVR54 issue. click
-
Now the most correct thing is to connect using the terminal and see what is displayed there.
-
Yes, I wrote above that this processor is not affected by the C2000 problem.
-
Your processor doesn't seem to be affected by the C2000 problem. Therefore, it is better to connect via TTL
-
Did you find how to connect to the terminal?
-
If you have connected the USB DOM and made a copy of it, then it is working. You need to check on another power supply, check the BIOS, if you have an Intel Atom, then it may be affected by the С2000 problem.
- 306 replies
-
- 1
-
-
- firmware
- 08-0220usb14
- (and 4 more)
-
I have compiled a bootloader for my DS218+. The image of a USB flash drive from 918+ was taken as a basis. In the first section, the SynoBootLoader.conf file was replaced, which was kindly provided to me by DSfuchs, thanks to him for this. The files on the second disk were replaced: checksum.syno, grub_cksum.syno, rd.gz, zImage, these files were used from the unpacked PAT file. The vender file contained the serial number and MAC address and their check amounts, with stickers on the motherboard. P.S. If you do not change the VID PID of the USB flash drive on F400, when installing the operating system from a PAT file, you will receive the error "cannot install DSM, the file may be damaged." P. S. I'm waiting for the USB DOM to burn the image on it and install it inside, as well as the CPU SR2Z9 4c / 4t .
-
-
In the evening I will try to collect all this, I will unsubscribe about the organization, once again many thanks for the help.
-
I correctly understood this Sone.9 from DS218 +? You can see the meaning of this file in the SynoBootLoader.cfg file from DS218+: syno_hdd_detect = 18 179 176 175 syno_hdd_enable=21,20,19,9 sata_remap="0>2:1>3:2>0:3>1 Thank you very much for your help.
-
The first section contains the file SynoBootLoader.cfg. I think that for 218+ these variables should have different values: syno_hdd_detect=18,179,176,175 syno_hdd_enable=21,20,19,9 syno_hw_version=DS918+ sata_remap="0>2:1>3:2>0:3>1 I looked in the unpacked firmware, there is no file Sone.9, I don't know where to get it DS218+ SynoBootLoader.cfg
-
I need the contents of this file, this is what it looks like from 918+, on which I managed to boot.
-
The original physical flash is disabled, since it does not work, it is now in this state. I would be very grateful to you if you could share the image of the original flash for DS 218+.
-
In 218+, you can install 16GB of memory, the approximate cost is $ 40, I think it's not that expensive. When I restore this NAS, I may try to change SR2Z8 to SR2Z9 as a result it will be 4c / 4t.
