menace

Brilliant! Thank you so much! Worked straight away using the "manual" command. I had to modify "synoinfo.conf" to enable SHR when using the "manual" command Did you have have to add the IXGBEVF ext to get SR-IOV functionality? It does not seem to be installed by default.

SynologyNAS login: SynologyNAS login: root Synology strongly advises you not to run commands as the root user, who has the highest privileges on the system. Doing so may cause major damages to the system. Please note that if you choose to proceed, all consequences are at your own risk. BusyBox v1.30.1 () built-in shell (ash) SynologyNAS> cat /var/log/junior_reason Exit on error [99] rp ext init exec failure... SynologyNAS> cat /var/log/*rc* START /linuxrc.syno.impl Insert Marvell 1475 SATA controller driver Insert basic USB modules... :: Loading module usb-common ... [ OK ] :: Loading module usbcore ... [ OK ] :: Loading module ehci-hcd ... [ OK ] :: Loading module ehci-pci ... [ OK ] :: Loading module xhci-hcd ... [ OK ] :: Loading module xhci-pci ... [ OK ] :: Loading module usb-storage ... [ OK ] :: Loading kernel modules from extensions ... Loading kmod #0 "dca.ko" for pocopico.igb (args: ) Loading kmod #1 "igb.ko" for pocopico.igb (args: ) Loading kmod #0 "udp_tunnel.ko" for pocopico.ixgbe (args: ) Loading kmod #1 "ip6_udp_tunnel.ko" for pocopico.ixgbe (args: ) Loading kmod #2 "dca.ko" for pocopico.ixgbe (args: ) insmod: can't insert 'dca.ko': File exists ERROR: kernel extensions "dca.ko" from pocopico.ixgbe failed to load Exit on error [99] rp ext init exec failure... Tue Apr 19 05:51:45 UTC 2022 none /sys/kernel/debug debugfs rw,relatime 0 0 SynologyNAS> Thanks for your help

Hi I have been using DS3622xs DSM 7.0.1-42218 for many weeks now without any errors. (Baremetal) I decided to upgrade to DSM 7.1.0-42661 using the process as described in this thread. I don't have any errors in the build process. Once rebooted, I have no problems accessing the Synology install screen. However, once the install completes, it reboots and goes directly back into the install screen again! This happens over and over. I decided to wipe all my drives (I have backup!) And start from scratch. However, I still run into the same problem! (Installation loop) Do you have any idea of what is going on? What commands do I need from the telnet screen to find out what is happening? Thanks in advance

Hi you have inadvertently left out DS3622 DSM 7.0.1-42218 in your rp-ext.json file for Atlantic (Marvell drivers) the TAR file and set up file are in the releases directory. Could you please correct? Thank you

Please create a module for 918+ DSM 6.2.4 the current SFC module in the repository does not support this particular network card. Thanks very much

It appears that the file "i2c-algo-bit.ko" has been left out of the tar file. Is it possible to get this corrected? Thank you very much. Sorry for all the duplicate posts. I cannot figure out how to delete a post!

Getting this error when trying to install Solarflare SFN7122f for 918+ 6.2.4

Many thanks! Now to do some testing

Could I please request a module for Solarflare SFN7122f 10 Gb network card for both 918+ and 3622xs? I have DSM 7.0.1 918+ working right now on my Asrock E3C232D2l motherboard but would also like to test 3622XS. Result from lspci: 0000:01:00.0 Ethernet controller [0200]: Solarflare Communications SFC9120 10G Ethernet Controller [1924:0903] (rev 01) RPM is available at: https://support-nic.xilinx.com/wp/drivers Thanks