Spats
-
Posts
87 -
Joined
-
Last visited
Posts posted by Spats
-
-
Board: Asus Prime Z270-P
CPU: I5 6400 (Skylake)
RAM: 8GB
I have Video station working with a 4k video it streams ok to samsung s21.
using Plex with Plex pass same video is working but cpu is high via edge or chrome win11
What are the commands to getting activation.conf and what drivers do i need.
TIA guys
EDIT: AME is working ok as well.
-
-
Hi, just installed the DS918+ with this loader but do you have drivers for Intel X520-DA2 as it does not recognize i have it.
and what would be the best way to add the drivers as well as the macs.
cheers guys
-
-
Guys managed to get the above installed but when it goes to reboot and starts the countdown it gets stuck in recover mode after counting down.
the setup is Dell R710 server.
2 x Intel Xeon L5630@2.13Ghz
24Gb DDR3 ECC memory
Dell Perc 200I flashed to IT mode
iDRAC6
4 QLOGIC BCM5709C onboardINTEL PRO 1000 dual 1gbe nic card that i am using
./rploader.sh update
./rploader.sh fullupgrade
./rploader.sh identifyusb./rploader.sh serialgen realmac
./rploader.sh listmods bromolow-7.0.1-42218
./rploader.sh build bromolow-7.0.1-42218
I install the DSM_DS3615xs_42218 pat file from but when it reboots to start it just counts down then it says recover.
I am stuck with this one guys
cheers
-
Guys managed to get the above installed but when it goes to reboot and starts the countdown it gets stuck in recover mode after counting down.
the setup is Dell R710 server.
./rploader.sh update
./rploader.sh fullupgrade
./rploader.sh identifyusb./rploader.sh serialgen realmac
./rploader.sh listmods bromolow-7.0.1-42218
./rploader.sh build bromolow-7.0.1-42218
it built it ok, I load the DSM_DS3615xs_42218 pat file from but when it reboots to start it just counts down it says recover.
-
Trying to load DSM7 DS3615xs on a R710 server cannot remember the procedure for redpill, looking for help on this guys.
it gets updated day by day so struggling with this, its a legacy system.
I can get jun's loader 1.0.1 dsm 6.0.1 working but looking to do full bare metal install of dsm 7 hence asking what the procedure is.
cheers
-
Would I be able to use this setup on a Dell Poweredge R710 guys.
Cheers
-
1 hour ago, cyberphoy said:
I installed a temporary cheap pci-e card in mine that RedPill Tiny core recognized and the setup was easy from there for DSM 7
Got one installed as well mate, but still doesn't give me an ip after I build the loader.
What version of dsm are you using.
-
Finally got it only with Jun's Loader 1.01, v6.0.2 DS3615xs_8451 pat file.
Got the 4 internal macs in the grub.cfg
I have a Perc H200I flashed in IT mode
So it looks as if i cannot take this anywhere else, as i have spent a lot of time reading the forum.
If anyone can shed a light in taking this up to 6.2 i would be happy with that.
Cheers
-
Guys got two Intel Xeon L5630 @2.13 GHz Processors 8 cores, 24 Gb memory.
BCM5709C 4 1 Gb ports plus 2.5Gb Realtek nic card installed.
what is the lowest BareMetal DSM i can go, then i can go from there.
cheers guys
-
cheers mate
18 minutes ago, flyride said:FWIW the script doesn't recognize "now" anymore and you cannot specify the mac address with realmac. It just takes the actual MAC from the hardware. Same result though, as long as you were typing in the hardware MAC.
./rploader.sh serialgen DS3622xs+ realmac
The only way to specify your own MAC address that is not the hardware MAC is to edit user_config.json yourself.
still not getting an IP from the 2.5gb card, albeit i am getting an IP when installing the TCRP loader tho.
Put the my own mac in still nothing.
-
Cheers mate, yes 008E25711489 is the real nic for the 2.5 gb card but I cannot access SA or find.synology.com.
Winscp cannot find my ip, and I only get an ip when configuring the TCRP loader after reboot nothing.
-
Thanks mate
these are the commands, and the list off what i done mate
much appreciated
./rploader.sh update now
./rploader.sh fullupgrade now
./rploader.sh identifyusb now
./rploader.sh serialgen DS3622xs+ realmac now./rploader.sh satamap
./rploader.sh build broadwellnk-7.1.0-42661 -
Thanks mate,
I have now ordered an Perc H200 card to flash to IT mode.
I tried to get the DS3622xs setup but it wouldn't give me an ip from any of the ports, so i disabled them.
I have a 2.5gbe card for my pc put it into the server and that gave me an IP address, used the real mac and port for that card.
loaded up the broadwellnk on the flash drive for DSM 7 but i get no ip, nothing from the router, so cannot boot from that to install DSM.
Will dig a bit deeper into trying to get this work.
cheers for your help mate
-
Thanks bud, I have ordered a perc h700 card to flash in IT mode.
Will look into the DS3622xs and give it a go.
I don't know anything virtualization of any kind, but willing to try.
Cheers
11 hours ago, rojoone2 said:The R710 is such a beast to only use it as a NAS. But you will probably have issues with the disks being recognized with the Perc 6i.
I don't believe there are drivers for that card and I'm unsure if can even be flashed to IT mode.
Have a look at this thread where members have had some success with Jun's Loader (DS3615xs and DS3617xs) and DSM 5 and 6 on a the R710:
Give the DS3622xs+ a try if you want DSM 7 using a test disk in one of the bays to see if the 6i would pass through and give access to the disks.
Would like to try to get DSM 7 on it.
Does this server support 12tb drives, need to test it.
-
Anyone any thoughts guys on how to get this up and running.
cheers
-
Admin, Mods can this topic be deleted, cheers
-
As per the heading
what dsm can i put on the R710
do i need new hardware etc to make it work.
no experience on server related stuff before.
I also want to use plex on it, but i can add a GTA 660 card for it, not bothered about that at the moment.
just need guidance guys
2 x Intel Xeon L5630@2.13Ghz
LFF 6x3.5inch bays
24Gb DDR3 ECC memory
Dell Perc 6/i integrated raid controller
2 x 870W 80plus silver
iDRAC6
4 onboard nic 1gb cardsGot win 10 installed on it at the moment.
Cheers guys
PS would prefer to install BareMetal if i can.
-
Guys / Gals
Is this server any good for dsm 7.1 if so what would be the recommended build to go for.
Cheers
Computer:
2 x Quad Core Intel Xeon E5506 (1MB L2 Cache, 4MB L3 Cache, 2.13Ghz) Processor
2 x CPU Sockets, Both CPUs Installed (12 CPU Cores, Logical Processors, 24threads)Memory:
6GB Of PC3 Memory (6 x 1GB)
Storage:
12 x 2TB 7.2K External Drives + 2 x 500GB 7.2K Internal Drives
Backplane:
1 x 12 Bay 3.5” LFF SATA, SAS, SSD
RAID:
Perc 6I RAID Controller With Battery Module (RAID 0, 1 & 5)
Power Supply:
2 x Redundant Power Supply (Cables Not Included)
Networking:
2 x Integrated 10,100,1000 (1GbE) Network Ports
Graphic:
Standard VGA (Cable Not Included)
Management System:
iDRAC 7 - Enterprise License
-
Thanks goes to @IG-88 for getting this sorted for me in the 6.2 build as the DS918+ only has 2 lan ports.
edit synoinfo.conf located in /etc.defaults/synoinfo.conf maxlanport="2" I changed it to 8.
Also edit /etc/synoinfo.conf maxlanport="2" I changed it to 8
Reboot you now have all mac addresses showing
Thanks goes to Pocopico and Peter Suh for helping me trying to get this sorted.
Edit: Now I got my 10gb NIC working.
- 2
-
Waited for a good 30mins for an IP still nothing.
is it possible to go the DS920+ route guys
cheers
-
19 minutes ago, pocopico said:
If you see disk activity, then probably there is no KP. Several people complain about the 10min wait for IP. did you leave the system up for about 10-15 mins and still dont get an IP ?
No mate, I get an ip within a minute without the 10g card,
But waited about 5 mins when card is in, so I could try the 10 to 15 min wait and see what happens.
- 1
-
5 minutes ago, pocopico said:
Do you have any serial console ? I think you might get kernel panic because of the ixgbe modules. Do you get any disk activity ?
No serial console, disk activity yes I get noise from hdd as its trying to boot, if that's what you mean mate
TCRP Have ds918+ working, but no activation.conf need help please.
in The Noob Lounge
Posted
Anyone with any ideas guys, as to why this is happening.