turbo21psi
-
Posts
25 -
Joined
-
Last visited
Posts posted by turbo21psi
-
-
14 hours ago, irishj said:
Seeing the same thing here with a LSI SAS 9207-8i, running on Baremetal. Any idea how to fix it or if it's even possible ?
I should note, I also have two NVMe drives for SSD caching and I don't see the info on the first page for them either, I do see smart data in the smart attribute section. These NVMe drives are connected directly to the motherboard.
I have another of these cards in an ESX host with passthrough to a 3622xs+ VM and don't see smart data on the overview page there either. I also have a NVMe drive (connected to motherboard) and passthrough to the VM and I don't see smart for that either on the overview page, so I don't believe it's a HBA controller issue.
I'm using a flashed DELL H710 which I believe is the same or similar to the LSI HBA and I noticed this same issue with both baremetal and ESX build for 7.01 on 3622xs+. DS3615 didn't have this issue on the same machines.
Upgrading to 7.1 fixed this issue for me.
-
1 minute ago, Dvalin21 said:
I dont think its the disk however i haven't tried 0F00 since I've made sure to turn the embedded ports off. I will have to try that. I noticed that you added the netif_num. I wonder, are the nics you are using individual or are they all on the same device? I have the T320 and i believe its the same device so I haven't had to include that for both of them to show up. Now I'm just being curious
They are 2 different cards. A single port intel NIC and a dual port Mellanox NIC. I disabled the onboard NICs.
-
13 minutes ago, Dvalin21 said:
Me and you have the H310 card, how are you or what are you doing for your drives to come up as "supported" Its like at random every time i build and then access it changes. I've looked at all the websites that have talked about satamap and diskidxmap and sasidxmap and I thought I understood, but I dont know what keeps the issue going. When it says the drives are unsupported that its not able to do secure erase or benchmarks. My settings are satamap 8 (all embedded sata ports are off. It was the only way to get it to put the drives in order. Im also not going to be using those ports), and diskid and sasid "0". I had it at 0 before and three out of the 4 disk showed up as being supported. Now 1 out of the 4 shows as being supported. I've changed the maxdisk to 8. If you dont mind could you share what your user_config.json settings? (obviously not your macs). I would really appreciate it. Maybe I can get this thing working fully finally. @turbo21psi has the same card or similar so the settings would be helpful for him and I would say many others as well. Thanks in advance.
This is what I'm using and all my disks are showing as normal. Could it be an issue with that specific disk perhaps?
{ "extra_cmdline": { "pid": "0x5571", "vid": "0x0781", "sn": " ", "mac1": " ", "mac2": " ", "mac3": " ", "SataPortMap": "8", "netif_num": "3", "DiskIdxMap": "0F00" }, "synoinfo": { "internalportcfg" : "0xffff", "maxdisks" : "16", "support_bde_internal_10g" : "no", "support_disk_compatibility" : "no", "support_memory_compatibility" : "no" }, "ramdisk_copy": { -
Thank you all for your amazing work.
Successfully update from 7.01 to 7.1 DS3622xs+ on a DELL R320 with a flashed H710 hba, onboard NIC disabled, using an intel gigabit nic and a mellanox 10G connectx4 nic.
I had the same failed to load issue earlier and the latest update fixed it. Also a fresh install of 7.01 straight to 7.1.
After the first successful postupdate, it booted to no disks detected. Tried again and added the mpt3sas extension before postupdate, disks were detected on reboot. It made me reinstall dsm, used the same PAT file I downloaded when manually updated and now have a working 7.1 install. Had to manually enable SHR through SSH. 10G Mellanox NIC is also working fine.
-
1
-
-
On 2/13/2022 at 6:21 AM, IG-88 said:
to understand this it need to looked into kernel versions
the above from @pocopico was for 918+, thats coming with kernel 4.4 and in that kernel the kernel-dev's merged mpt2sas and mpt3sas, so there is usually only mpt3sas (there is a option in the kernel for backward compatibility that will create a mpt2sas, but thats optional)
Is this why I can't get DS3617 to work with my LSI SAS2308 HBA (flashed DELL H710 mini) while DS3615 works just fine if I manually add the mpt2sas extension?
If I understand it correctly, for DS3617 with kernel 4.4, the correct driver is mpt3sas but it needs to have the backward compatibility option and the one available now doesn't have it turned on?
-
Unsuccessful on Asrock J3455M, the micro-atx version. 6.1 works perfectly on this board. I suspect it's an issue with the onboard NIC. It looks like it boots up but the NIC doesn't initialize (light doesn't turn green).
From other's posts, it sounds like the itx version works just fine.
I tried using an intel NIC (Intel(R) Gigabit CT Desktop Adapter), that also did not work.
-
To answer your question, it is possible. However, to go into further details would be a violation of the forum rules.
-
1
-
-
3 hours ago, Cr4z33 said:
Test on an empty spare hard drive was succesfull with hardware in signature!
Now how should I upgrade by using the normal system without loosing personal data and config?
I was a little paranoid so I took extra steps after I confirmed 6.2 was working on a spare drive. I actually tried to mimic my current install on the spare drive and did a test migration. That went well so I went ahead with my real disks.
-
Thanks Jun!
Everything looks to be working on my box:
Baremetal DS3617, Supermicro X10slm+-f, E3-1220v3, LSI 9211-8i (IT mode)
Using both onboard SATA and HBA.
Migrated disks with 6.1 to 6.2 with no issues.
-
I booted up 6.2 again with the custom extra.lzma and got about the same error messages. It's super late when I was doing this and I may have done something wrong, but when trying to install DSM with only a drive connected to the HBA, the installer reported no disks detected. Installed dsm on a disk connected to the onboard sata and once booted, it can detect disks on the hba again.
-
Thanks for all your work on these! My LSI 9211-8i (IT mode) came in yesterday and I did some testing on my 6.2 box. It's a Supermicro x10slm+-f with E3-1220v3. 6.2 is running well and stable on it with just the onboard SATA ports.
Plugged in the LSI and booted with the standard loader. As expected, drives were not detected on the LSI card.
Added the modified extra.lzma to the usb and it booted fine and disks were detected on the LSI card but with some issues.
1. Hotswap was broken, it's fine when plugging in but when a disk is taken out, dsm will crash and reboot.
2. S.M.A.R.T. data were missing on the disks plugged into the LSI card.
Messed around with BIOS settings for a bit with no luck. To rule out if it's a hardware issue, I booted up 6.1(DS3617) with the 1.02b loader and everything appears to be working. Hotswap doesn't crash and S.M.A.R.T readings were available.
I'm in no rush to transfer my "production" disks to this box so I'm open for more testing later. This is somewhat new to me so I don't know what kind of logs to pull and share at this time.
-
1 hour ago, ming0070913 said:
Btw has anyone updated to DSM 6.2-23739 Update 2 yet? How's that?
Results for that are reported here:
-
- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.2-23739 UPDATE 1
- Loader version and model: JUN'S LOADER v1.03a2 - DS918+
- Using custom extra.lzma: NO
- Installation type: Baremetal - Supermicro x10slm+-f, e3-1220v3
- Additional comments: No issues, reboot less than 5 minutes.
-
51 minutes ago, Olegin said:
Can you post here the result of this command in telnet/ssh:
cat /usr/syno/etc/codec/activation.confNot OP but this is what I get with that command:
{"success":false,"msg":"SN format is wrong."}
-
On 7/12/2018 at 12:44 AM, Sonnyboy666 said:
Sorry for rushing in, but I have a Plex Pass and for me Hardware Acceleration is working with Plex and Videostation.
I am running DSM 6.2 on a DELL Poweredge T30 with an Intel Xeon E3-1225 v5.
I also have Plex pass and I did a manual install using a package from their site and now the hardware acceleration option is available. Plex works with it checked and doesn't crash, but since my system doesn't have an iGPU I'm pretty sure it doesn't do anything.
As far as updates on stability, I have 6.2 up and running since tuesday(4 days) with no crashes or reboots. The stuff I've done so far are: file transfers, hyperbackup (usb backup and restore), VM manager and just installing random apps. I'll see if I can find some old drives this weekend and try to build an array and see how that goes.
-
Loader version and type (918+): 1.03a2 DS918+
DSM version in use (including critical update): DSM 6.2-23739 Update 1
Using custom modules/ramdisk? If yes which one?: None
Hardware details: MB: Supermicro X10SLM+-F, E3-1220v3, onboard NIC (Intel I210-AT), onboard SATA
-
34 minutes ago, AndreyATGB said:
I find it hard to believe it actually works with no GPU. If you play a video that requires transcoding (HEVC for example) does it say -hwaccel in top as an argument to ffmpeg? Plex for Synology definitely supports it, you need Plex Pass and a compatible loader. There's people with Plex Pass running with hw accel on DS918+ for example.
Oh I wasn't saying hardware acceleration was working, just that the check box to turn it on is available. I'm pretty sure checking that box will do nothing for that server.
I installed Plex using just what's available in the package center.
-
1 hour ago, Rhubarb said:
Hi,
Out of curiosity, what do you have you system configured as: DS918+, 916,3615xs, 3617xs?
The one I'm testing 1.03a2 on is configured as DS918+. I actually just built this box yesterday and weighing in if I should jump into 6.2 or stay with 6.1 when I migrate my "production" disks.
-
5 hours ago, AndreyATGB said:
Wouldn’t that be because the E3-1220v3 doesn’t have an iGPU? I was under the impression that you need a GPU of some sort to use hardware accelerated encoding.
Good point, but the one with the hardware acceleration option is on a DL380-G7 (X5660 CPUs) which I don't believe have an iGPU either. I think Plex build for synology machines just don't have this option, which kind of make sense since it probably wouldn't work anyway.
-
Plex transcoding is working. I forced playback to transcode and it was doing it. Got up to 3 streams before cpu is pegged at 100%. I'm not sure how accurate the cpu usage meter is, I feel like it shouldn't hit 100% on 3 transcodes.
The option for hardware acceleration doesn't seem to be available for the DSM installed plex server.
-
1.03a2 seems to be working just fine on Supermicro X10SLM+-F with E3-1220v3. Motherboard has 2 NIC ports and both are detected, LACP bond working. No additional sata or nic card, just onboard for now. USB 3.0 ports work fine, was able to get over 100mbps transfer rate.
Videostation doesn't seem to work for some files, is that the transcoding issue? I don't really intend on using that app, but I thought I'd test it. DSM doesn't crash though, just some videos will not play.
So far it seems pretty good to me. Only have it up for a few hours but no random crashes or anything. Most of the things I tried are working. Plex, AD integration, NIC Bonding.
I only have 1 spare disk for testing so I haven't tried making RAID arrays yet.
Anything other things I should be testing? I'm open for suggestions.
-
Just wanted to say thanks! Your post saved me a ton of potential headaches. I was lucky enough to see this post before I started the build on my p5q pro.
-
I now have 2 "servers" built from my old desktop gaming PC and a hand me down 2006 Mac Pro.
2006 Mac Pro
- upgraded processors to 2x Xeon x5355 (2.6ghz quad core), bought for $25 on ebay
- 20 GB DDR2 RAM (cheap amazon brand)
- running headless as an ESXi server
VM 1 - Windows Server 2012: for Active Directory DC
VM 2 - Windows Server 2012: sql server, sharepoint for learning
VM 3 - Centos 7: plex, rclone backup, and used for learning linux in general
- I'm considering running Untangled as another VM on this server
Gaming Desktop from 2009 repurposed as Xpenology NAS
- DSM 6.02, using Jun's bootloader 1.01 on a usb stick
- Asus P5Q-Pro Turbo
- modded Xeon x5460 to fit socket, overclocked to 3.8ghz with water cooling. (I should probably remove the overclock but it's been stable for years and I'm scared to change the settings now)
- 8 GB RAM
- 4 x 2TB WD drives (2 WD REDs are new, 2 other WD drives I've had for a while and repurposed)
- Coolermaster CM690 case. 3.5" bays are pretty much full but I could use the 5.25" bays with some brackets should I need to add more drives
I'm using the NAS to store pictures and videos. I do a little photography/videography so there are a lot of these. I'm also storing media for the plex server and the home folders for active directory users.
Since I have a separate ESXi server, I'm pretty much only using the xpenology as a NAS. I'm not running any apps on it yet. Fortunately the motherboard worked with xpenology as is. There are 5 sata ports, plus 2 more that appears to be eSATA, I'm not sure if those will work for additional drives.
Yes, I know.... my power draw is probably stupid.
TinyCore RedPill Loader (TCRP)
in Loaders
Posted
I used this extension https://raw.githubusercontent.com/pocopico/rp-ext/master/mpt3sas/rpext-index.json
I have a flashed Dell H710 which I believe is the same as yours after the flash.