Oliveiras
-
Posts
12 -
Joined
-
Last visited
Posts posted by Oliveiras
-
-
17 hours ago, dj_nsk said:
Do you use virtual disks in ESXi for the DSM virtual machine? How did you manage to increase its size?
And why don't you want to do it in a simple way: make a backup - delete the old disk - add a new disk - restore from backup?
I'm using proxmox but the principles are the same.
I'm not trying to expand data volumes, it's the main system drive because a docker container fill the drive with logs.
So I cannot copy the xpenology system volume to other drive.
-
On 12/22/2022 at 11:11 AM, Burny said:
Hey guys,
i know this topic is quite old, but i also like to extend my volume on DSM 7.1.1. Unfortunately the command "syno_poweroff_task -d" isn't available anymore in DSM 7. I have found something similar, but it's still not working for me. It's this one: "synostgvolume --unmount -p volume1".
When i then try to run "mdadm --stop /dev/md2", it tells me "mdadm: Cannot get exclusive access to /dev/md2:Perhaps a running process, mounted filesystem or active volume group?".
Do you guys know any solution for that?
Thank you very much!
With kind regards,
Burny
I'm on the same boat !
Any one done it on DSM 7.1 ?
I also tried to skipp the `mdadm --stop` command as @cwiggs mentioned but no luck!
-
Hello all,
After adding the "args" to the VM conf file the drives apear in the VM when booted but not at hardware section on the proxmox VM.
Any thing missing besside the "args" line ?
Thanks
-
On 12/20/2018 at 1:00 PM, codedmind said:
Anyone can make and share a vm template for 1.04b ?
Thanks
Yes Pleasseee
-
Hello,
So there's no way to get the vmxnet3 10GBe working with DSM6.2?
I was trying to install synoboot 1.04b with ds918 but it doesn't show up on my network. Tried on VMworkstation on my desktop i7-7820x and it shows up but in a diferent subnet and can't access it!!!
So the HP micro G8 it's not compatible with the later loader and drivers right ?
-
Hello,
Can I use this script with 5.2-5592 ?
Thanks
-
I got it working... just HDD out of order on the DELL chassis!
But they have to be on the order on boot if not it will just order HDD for the order we just put them, but since the H310 controler boot them on order it's ok.
-
Hi,
I've choosed the C2100 FS12-TY (2x L5630 / 32GB DDR3 / H700) and I'm running xpenology DSM 5.2-5592 Update 2 baremetal since it have IPMI included and 2x 2.5" HDD inside for SSD and also 18 DDR3 slots for future upgrades or if I want to convert the machine to a VMware host.
Been doing some tests and tune ups but everything works 90% OK till I sort everything up:
-replaced H700 for a H310 crossflashed to LSI-9211-8i (done)
-BIOS reverted to B16 so it can load VMware ESXi in the future (done)
-BMC reverted to v1.70 for lower fan noise (done)
-added mellanox 10GBe nic card (done)
-CPU load in xpenology is allways at 10% don't know why, and CPU is not throtled back, is allways at 2.13Ghz (100%) at idle!
-don't know how or if needed to activate write cache in xpenology (gives error), since I'm not having too good write speeds for 12x 3.5" HDD and H310 card (130 - 150 MB/s with 10GBe network) have to do more tests
But it's working, not at 100% but it's ok.
-
As I've wrote on other post I have a dell H310 2008 chip card flashed to LSI 2118IT and have the drives ordering problem, but if I use the card with original firmware from dell H310 it works ok, disks are in correct order on DSM and card Bios, only don't have SMART status in DSM!
So could be firmware related the ordering issue?
-
Hello,
I've searched a lot about this "issue" of the LSI cards and can I ask if anyone found a way to get arround it? In DSM or even in LSI card?
I have a H310 flashed to 2118IT but can't get in to the advanced functions with the LSIUTILS, so I can try to reset the disk position and start over, and also to map them directly to the correct physical port!
Any clue why or anyone made it?
Any way I get the H310 pass also the SMART status to DSM with the dell firmware?
With dell original firmware the disks are ordered correctly and passthrough works but only SMART doesn't shows in DSM!
So saying that random drive bay layout is a LSI thing, it's not, since the H310 with Dell firmware doesn't do that!
PS: I'm using a DELL server C2100 F12-TY model with sas expander with 12 HDD bays.
-
Hello,
I've been looking for this servers for some time now, along side the HP DL180 G6, but now I have a good deal for a pair of FS12-TY but the same seller also have the R510 with the exact same config ( 2xL5630 / 32GB (8x4GB) / H700 512mb / 1x750W ) but for 130€ more each.
For what I've researched the R510 is more upgradable and it have better driver support and also is VMware 5.5 compatible instead of the 5.1 FS12-TY.
I will use these servers for xpenology only to store backups or if they won't work for this in the future I might install Vmware in it later.
Any advice on what to choose guys, the R510 or FS12-TY based C2100 ?
Thanks
Posted via Xpenology.us
Expand/resize btrfs Syno volume after disk space increased (ESXI, Hyper-V, ....))
in Tutorials and Guides
Posted
I need to expand volume 1 that includes base system files:
/dev/mapper/cachedev_1 btrfs 21G 21G 0 100% /volume1
Label: '2023.01.15-18:30:06 v42962' uuid: 2b590ef9-e408-48dd-bed5-e407b5b9bff2
Total devices 1 FS bytes used 20.13GiB
devid 1 size 21.00GiB used 21.00GiB path /dev/mapper/cachedev_1
The comands mentioned on this topic don't work on DSM 7.1