Timon-H

It says it's booting but No Webinterface is loading. Sometimes the loader bricks my ethernet or something I think

All I've done is updating the bios, installing the new CPU in the same mainboard and yes the bios update resets also the bios. Since then its done. Buuuut iam poking around in the arc loader and saw some stuff that can maybe fix it. But now it's not booting at all so something is wrong I guess 😂

I have a spare disk and that disk also doesn't get detected. It's something about the portmapping or something like that. My board has only 4 Sata ports but it also displays 4 "dummy" ports in software or something. The stupid thing is it worked with the i3 and now after a CPU upgrade it's fu**ed.. iam playing with the idea of buying a pcie to sata card to hopefully get it fixed that way...

I tried multiple times to reinstall the arpl loader. What do you mean with arc loader? Do you mean the arpl loader? Edit: I guess you mean this loader: https://auxxxilium.tech/redpill/ I tryed that just now. Same issue. No Drives detected.

Hello, I hope someone can help me. My NAS was running for about a year without problems. But then i installed a new CPU..... This is what i did: Installed the newest BIOS and swapped my "old" i3-12100 to a i7 13700k. Booted up the system, set my XMP Profile and Fan Curve and Booted right into the ARPL Loader that i used right before i swapped the CPU and boom: Its German and means: No Drives detected in your DS3622xs+. connect drives and click "refesh" and so on... I tryed swapping the i3 back in and downgrading the Bios without any luck. The Problem is here to stay. I also other versions of ARPL, also no luck. I dont know what else i can do to fix this... The Sata Controller is in AHCI Mode and Hotswapp is turned on (tryed it with off as well). My board: Biostar B660GTN with Realtek RTL8125B 2,5Gbit onboard LAN. I use the onboard SATA Connectors. Is this maybe some Sata Portmapping issue? In the ARPL setup i can see 4 greyed out DUMMY Ports and 4 green Ports. So the detection from ARPL should work fine or not? Thanks for helping and sorry for my bad english

I now got the connection back! I upgradet to the oldest bios that still supports the i7, switched in the i7, used an older version of the bootloader and now it boots! but still the "no drives found" problem.... can someone help me with that?

The problem is, it worked. It worked for months just fine. But then i had to upgrade the CPU.... Now its RIP.. I hate it

Mainboard: Biostar b660GTN with Realtek RTL8125B Controller. For me all Modules are pre selected. So all those drivers should be present.

I now tryed a Ubuntu Stick i have kicking around. Boots right up to desktop. Its just something wrong with my Bootloader i guess. Thats how i install ist: 1. burn arpl to Usb 2. Boot from usb 3. configure model (DS3622XS+) 4. configure Buildnumber (42962) 5. use Serialgen. 6. build loader 7. Boot loader. 8. try to load the webui (in my case 192.168.178.59:5000) Nothing loads. Before i installed the old bios i would get some "please wait" and then the notification that no drives are detected. In bios all drives where detected tho. But now i get nothing..

Now it's completely rip. I installed the oldest bios and now the os doesn't boot at all. I have tryed reformating the usb stick and loading the bootloader again. No success. It tryes to boot, everything looks like it's booting but the website doesn't show anything even after 20min of waiting. Iam so done man. All my data is on those 4 drives and a simple CPU upgrade crashes the hole system. Yes I know I need a backup but I don't yet have one.. my friend wants a Nas then I can backup to his Nas but atm I don't yet have a good backup solution... Iam now trying a different usb stick i guess.. I don't have any other idea

I searched the UEFI again. in the drive list section i can see AHCI Mode. I cant change that but dont need to. i guess the Uefi Settings are fine.. So why then is the OS not picking up drives. I cant even login. The webui instantly says no drives detected... I only changed CPU and updated the BIOS wtf?? Iam thinking of installing the i3 again and downgrading the Bios just to get it (hopefully) to work again. Edit: I tryed now the i3 again. Same problem. Now iam going to install the oldest Bios i can find to check if that fixes it.

Something just broke ig. Since i updated the Bios (for the new CPU gen) i lost the Option to pick between AHCI and RAID in the Sata config menu. I now tryed the oldest Bios version that still supports the 13700k, still no AHCI setting. Maybe i should just buy a PCIe to Sata port card.... Do you guys have a recommendation for a 4-8Port card?

I just Upgraded my NAS from a i3 12100 to a i7 13700k and now my Drives are no longer detected by the OS. In Bios i enabled hotplug and all drives are detected there. But if i boot the OS i cant get to the login, i just get a "no drives detected" warning where i can refresh. Any idea how or why this is? I tryed to rebuild the bootloader and there the Sata ports are green so it should work?? Iam very much confused

This one:

I would suggest the other bootloader stuff that @renegadeBE linked higher up this thread. I tried hours to get it to work with manual trying different Sataportmap and SATA remap, nothing worked. But this loader.. it just worked and was very easy to setup.

Yee but I still would need to open the ports with an domain. The domain would only translate my IP address to the Domain name.

I got a fixed IPv4. So i just going to open up some Ports for the NAS i think.

Yes it works now! Yes DS3622xs+ By the way, is there a way to connect with Synology Account? I guess not? I don't need it, but it would be a nice to have I guess

Iam an Idiot! I tried to install the software with only some Patch files, not the real software!

OMG iam so dumb... Iam so sorry for all the trouble 😕 I got some Update Patch with 50mb size.. downloadet the right package and tried again. Its working! Thank you so much!

Thanks! Iam struggling for over 1 day continues installing DSM...Trying different versions all day long, editing the user config... Its a jurney.. I would be sooo happy if you find the problem!

OMG with that software i got it to work... sort of. My Drives are now all there and i can upload the image from the Synology OS. But after 41-42% it gives me some error that the file is corrupted... I just downloaded it.. And yes i used the correct version...

No? I have an Realtek RTL8125B Controller and i loadet now the driver for the RTL8125 controller. With that i can load the Web Assistant and upload the Image, but it crashes. At around 40% i get some error that the file is corrupted, but i just downloadet it from the offical Synology website. Any Idea why this error is happening?

Yee i forgot the driver.. have tried befor a installation were the driver was included with the bootloader or something like that.. I have no Idea how to get the console with this redpill loader, i only have this gui interface. But i booted the Tinycore bootloader where i have an console. Here is the stuff tc@box:~$ lspci -nnvk 00:00.0 Host bridge [0600]: Intel Corporation Device [8086:4630] (rev 05) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: bus master, fast devsel, latency 0 Memory at <ignored> (32-bit, non-prefetchable) 00:02.0 VGA compatible controller [0300]: Intel Corporation Device [8086:4692] (rev 0c) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device [1565:111a] Flags: bus master, fast devsel, latency 0, IRQ 255 Memory at 6000000000 (64-bit, non-prefetchable) [size=16M] Memory at 4000000000 (64-bit, prefetchable) [size=256M] I/O ports at 4000 [size=64] [virtual] Expansion ROM at 000c0000 [disabled] [size=128K] Capabilities: <access denied> 00:0a.0 Signal processing controller [1180]: Intel Corporation Device [8086:467d] (rev 01) Flags: fast devsel Memory at 6001110000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> 00:14.0 USB controller [0c03]: Intel Corporation Device [8086:7ae0] (rev 11) (prog-if 30 [XHCI]) Subsystem: Biostar Microtech Int'l Corp Device [1565:6410] Flags: bus master, medium devsel, latency 0, IRQ 125 Memory at 6001100000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:14.2 RAM memory [0500]: Intel Corporation Device [8086:7aa7] (rev 11) Flags: fast devsel Memory at 600111c000 (64-bit, non-prefetchable) [disabled] [size=16K] Memory at 6001124000 (64-bit, non-prefetchable) [disabled] [size=4K] Capabilities: <access denied> 00:15.0 Serial bus controller [0c80]: Intel Corporation Device [8086:7acc] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: bus master, fast devsel, latency 0, IRQ 255 Memory at 4017000000 (64-bit, non-prefetchable) [disabled] [size=4K] Capabilities: <access denied> 00:15.1 Serial bus controller [0c80]: Intel Corporation Device [8086:7acd] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: bus master, fast devsel, latency 0, IRQ 255 Memory at 4017001000 (64-bit, non-prefetchable) [disabled] [size=4K] Capabilities: <access denied> 00:16.0 Communication controller [0780]: Intel Corporation Device [8086:7ae8] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: fast devsel, IRQ 255 Memory at 6001121000 (64-bit, non-prefetchable) [disabled] [size=4K] Capabilities: <access denied> 00:17.0 SATA controller [0106]: Intel Corporation Device [8086:7ae2] (rev 11) (prog-if 01 [AHCI 1.0]) Subsystem: Biostar Microtech Int'l Corp Device [1565:5225] Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 124 Memory at 80600000 (32-bit, non-prefetchable) [size=8K] Memory at 80603000 (32-bit, non-prefetchable) [size=256] I/O ports at 4090 [size=8] I/O ports at 4080 [size=4] I/O ports at 4060 [size=32] Memory at 80602000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1d.0 PCI bridge [0604]: Intel Corporation Device [8086:7ab6] (rev 11) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0, IRQ 122 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00003000-00003fff [size=4K] Memory behind bridge: 80500000-805fffff [size=1M] Prefetchable memory behind bridge: None Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.7 PCI bridge [0604]: Intel Corporation Device [8086:7ab7] (rev 11) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0, IRQ 123 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: None Memory behind bridge: 80400000-804fffff [size=1M] Prefetchable memory behind bridge: None Capabilities: <access denied> Kernel driver in use: pcieport 00:1f.0 ISA bridge [0601]: Intel Corporation Device [8086:7a86] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: bus master, fast devsel, latency 0 00:1f.3 Audio device [0403]: Intel Corporation Device [8086:7ad0] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:8260] Flags: fast devsel, IRQ 255 Memory at 6001118000 (64-bit, non-prefetchable) [disabled] [size=16K] Memory at 6001000000 (64-bit, non-prefetchable) [disabled] [size=1M] Capabilities: <access denied> 00:1f.4 SMBus [0c05]: Intel Corporation Device [8086:7aa3] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: medium devsel, IRQ 255 Memory at 6001120000 (64-bit, non-prefetchable) [size=256] I/O ports at efa0 [size=32] 00:1f.5 Serial bus controller [0c80]: Intel Corporation Device [8086:7aa4] (rev 11) Subsystem: Biostar Microtech Int'l Corp Device [1565:3118] Flags: fast devsel Memory at 80604000 (32-bit, non-prefetchable) [size=4K] 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. Device [10ec:8125] (rev 05) Subsystem: Biostar Microtech Int'l Corp Device [1565:2314] Flags: bus master, fast devsel, latency 0, IRQ 18 I/O ports at 3000 [size=256] Memory at 80500000 (64-bit, non-prefetchable) [size=64K] Memory at 80510000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 02:00.0 Network controller [0280]: Intel Corporation Wireless 7265 [8086:095a] (rev 59) Subsystem: Intel Corporation Dual Band Wireless-AC 7265 [8086:5010] Flags: fast devsel, IRQ 255 Memory at 80400000 (64-bit, non-prefetchable) [disabled] [size=8K] Capabilities: <access denied> And with the command "dmesg | fgrep "ata"" i get this: 0.000000] BIOS-e820: [mem 0x0000000075703000-0x00000000757d6fff] ACPI data [ 0.052885] Memory: 16041500K/16549512K available (10242K kernel code, 1227K rwdata, 1916K rodata, 1184K init, 3660K bss, 507756K reserved, 0K cma-reserved) [ 0.199443] libata version 3.00 loaded. [ 0.375989] ata1: DUMMY [ 0.375990] ata2: DUMMY [ 0.375990] ata3: DUMMY [ 0.375990] ata4: DUMMY [ 0.375997] ata5: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602300 irq 124 [ 0.375998] ata6: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602380 irq 124 [ 0.376000] ata7: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602400 irq 124 [ 0.376001] ata8: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602480 irq 124 [ 0.376427] scsi host8: pata_legacy [ 0.376448] ata9: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14 [ 0.687910] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 0.687931] ata8: SATA link down (SStatus 0 SControl 300) [ 0.687951] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 0.687972] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 0.688827] ata7.00: supports DRM functions and may not be fully accessible [ 0.688852] ata5.00: supports DRM functions and may not be fully accessible [ 0.688870] ata6.00: supports DRM functions and may not be fully accessible [ 0.688933] ata7.00: ATA-10: CT1000MX500SSD1, M3CR043, max UDMA/133 [ 0.688935] ata7.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 0.688965] ata5.00: ATA-10: CT1000MX500SSD1, M3CR043, max UDMA/133 [ 0.688966] ata5.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 0.688986] ata6.00: ATA-10: CT1000MX500SSD1, M3CR043, max UDMA/133 [ 0.688987] ata6.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 0.690554] ata7.00: supports DRM functions and may not be fully accessible [ 0.690586] ata5.00: supports DRM functions and may not be fully accessible [ 0.690608] ata6.00: supports DRM functions and may not be fully accessible [ 0.691283] ata7.00: configured for UDMA/133 [ 0.691373] ata5.00: configured for UDMA/133 [ 0.691381] ata6.00: configured for UDMA/133 [ 0.728037] scsi host8: pata_legacy [ 0.728057] ata10: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15 [ 0.901463] usbcore: registered new interface driver ums-datafab [ 0.960712] Write protecting the kernel read-only data: 14336k [ 0.961958] Freeing unused kernel image (text/rodata gap) memory: 2044K [ 0.962082] Freeing unused kernel image (rodata/data gap) memory: 132K

tc@box:~$ dmesg | fgrep "ata" [ 0.000000] BIOS-e820: [mem 0x0000000075703000-0x00000000757d6fff] ACPI data [ 0.052885] Memory: 16041500K/16549512K available (10242K kernel code, 1227K rwdata, 1916K rodata, 1184K init, 3660K bss, 507756K reserved, 0K cma-reserved) [ 0.199443] libata version 3.00 loaded. [ 0.375989] ata1: DUMMY [ 0.375990] ata2: DUMMY [ 0.375990] ata3: DUMMY [ 0.375990] ata4: DUMMY [ 0.375997] ata5: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602300 irq 124 [ 0.375998] ata6: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602380 irq 124 [ 0.376000] ata7: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602400 irq 124 [ 0.376001] ata8: SATA max UDMA/133 abar m2048@0x80602000 port 0x80602480 irq 124 [ 0.376427] scsi host8: pata_legacy [ 0.376448] ata9: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14 [ 0.687910] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 0.687931] ata8: SATA link down (SStatus 0 SControl 300) [ 0.687951] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 0.687972] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 0.688827] ata7.00: supports DRM functions and may not be fully accessible [ 0.688852] ata5.00: supports DRM functions and may not be fully accessible [ 0.688870] ata6.00: supports DRM functions and may not be fully accessible [ 0.688933] ata7.00: ATA-10: CT1000MX500SSD1, M3CR043, max UDMA/133 [ 0.688935] ata7.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 0.688965] ata5.00: ATA-10: CT1000MX500SSD1, M3CR043, max UDMA/133 [ 0.688966] ata5.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 0.688986] ata6.00: ATA-10: CT1000MX500SSD1, M3CR043, max UDMA/133 [ 0.688987] ata6.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 0.690554] ata7.00: supports DRM functions and may not be fully accessible [ 0.690586] ata5.00: supports DRM functions and may not be fully accessible [ 0.690608] ata6.00: supports DRM functions and may not be fully accessible [ 0.691283] ata7.00: configured for UDMA/133 [ 0.691373] ata5.00: configured for UDMA/133 [ 0.691381] ata6.00: configured for UDMA/133 [ 0.728037] scsi host8: pata_legacy [ 0.728057] ata10: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15 [ 0.901463] usbcore: registered new interface driver ums-datafab [ 0.960712] Write protecting the kernel read-only data: 14336k [ 0.961958] Freeing unused kernel image (text/rodata gap) memory: 2044K [ 0.962082] Freeing unused kernel image (rodata/data gap) memory: 132K