Abend zusammen,
kann jemand erklären wie genau die Umrechnung der Schnittenstellenangaben funktioniert?
tc@box:~$ sudo lspci
00:00.0 Host bridge: Intel Corporation Device 3e0f (rev 07)
00:01.0 PCI bridge: Intel Corporation Skylake PCIe Controller (x16) (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Device 3e90
00:12.0 Signal processing controller: Intel Corporation Device a379 (rev 10)
00:14.0 USB controller: Intel Corporation Device a36d (rev 10)
00:14.2 RAM memory: Intel Corporation Device a36f (rev 10)
00:16.0 Communication controller: Intel Corporation Device a360 (rev 10)
00:17.0 SATA controller: Intel Corporation Device a352 (rev 10)
00:1c.0 PCI bridge: Intel Corporation Device a33d (rev f0)
00:1c.6 PCI bridge: Intel Corporation Device a33e (rev f0)
00:1d.0 PCI bridge: Intel Corporation Device a330 (rev f0)
00:1f.0 ISA bridge: Intel Corporation Device a304 (rev 10)
00:1f.3 Audio device: Intel Corporation Device a348 (rev 10)
00:1f.4 SMBus: Intel Corporation Device a323 (rev 10)
00:1f.5 Serial bus controller [0c80]: Intel Corporation Device a324 (rev 10)
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (7) I219-V (r ev 10)
02:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection ( rev 03)
03:00.0 Network controller: Intel Corporation Device 24fb (rev 10)
04:00.0 Non-Volatile memory controller: Micron Technology Inc Device 5410 (rev 0 1)
Soweit ich das sehe:
6xSATA = 00:17.0
NIC1 = 00:1f.6
NIC2 = 02:00.0
NVME SSM = 04:00.0
Meine Model.conf (läuft leider nicht) soll ein TS-653D werden.
[System Enclosure]
VENDOR = QNAP
MODEL = TS-653D
CAP=0x16149b9c
MAX_DISK_NUM = 6
MAX_FAN_NUM = 2
MAX_TEMP_NUM = 2
INTERNAL_NET_PORT_NUM = 2
MAX_PCIE_SLOT = 1
CPU_TEMP_UNIT = DTS:4
SYSTEM_TEMP_UNIT=EC
SIO_DEVICE = IT8528
PWR_RECOVERY_UNIT = EC
BOARD_SN_DEVICE = VPD:BP
ETH_MAC_DEVICE = NET
DISK_DRV_TYPE = ATA
DISK_DEFAULT_MAX_LINK_SPEED = PD_SATA_SAS_6G
SYSTEM_DISK_CACHEABLE_BITMAP = 0x7E
SS_MAX_CHANNELS = 40
SS_FREE_CHANNELS = 4
EUP_STATUS = EC
LCM_BAUDRATE = 115200
[System FAN]
FAN_UNIT = EC
FAN_1=I1
FAN_2=I2
FAN_LEVEL_0 = 0
FAN_LEVEL_1 = 70
FAN_LEVEL_2 = 90
FAN_LEVEL_3 = 110
FAN_LEVEL_4 = 130
FAN_LEVEL_5 = 150
FAN_LEVEL_6 = 200
FAN_LEVEL_7 = 250
HEAT_SOURCE = SYS, CPU, DISK
[System I2C]
DEV_BUS = B00:D31:F1
DEV_PORT = 0
[System EDID 1]
DEV_BUS = B00:D02:F0
DEV_PORT = 0
[System IO]
RESET_BUTTON = EC
USB_COPY_BUTTON = EC
STATUS_GREEN_LED = EC
STATUS_RED_LED = EC
VPD_MB = EC
VPD_BP = EC
FRONT_USB_LED = EC
LED_BV_INTERFACE = EC
LED_BV_CTRL = PWM
EDID_COUNT=1
VOICE_ALERT_SUPPORT = 0
[System Disk 1]
DEV_BUS=B00:D23:F0
PCI_SWITCH_PORT = 7
DEV_PORT = 0
ERR_LED = EC
LOCATE_LED = EC
[System Disk 2]
DEV_BUS=B00:D23:F0
PCI_SWITCH_PORT = 7
DEV_PORT = 1
ERR_LED = EC
LOCATE_LED = EC
[System Disk 3]
DEV_BUS=B00:D23:F0
DEV_PORT = 2
ERR_LED = EC
LOCATE_LED = EC
[System Disk 4]
DEV_BUS=B00:D23:F0
DEV_PORT = 3
ERR_LED = EC
LOCATE_LED = EC
[System Disk 5]
DEV_BUS=B00:D23:F0
DEV_PORT = 4
PRESENT_LED = EC:1
BLINK_LED = EC:1
ERR_LED = EC
LOCATE_LED = EC
[System Disk 6]
DEV_BUS=B00:D23:F0
DEV_PORT = 5
PRESENT_LED = EC:2
BLINK_LED = EC:2
ERR_LED = EC
LOCATE_LED = EC
[System Network 1]
DEV_BUS = B00:D20:F1
DEV_PORT = 0
PCI_SWITCH_PORT = 3
[System Network 2]
DEV_BUS = B02:D00:F0
DEV_PORT = 0
PCI_SWITCH_PORT = 3
[System PCIE SLOT 1]
DEV_BUS = B04:D00:F0
[Usb Enclosure]
VENDOR = QNAP
MODEL = USB
MAX_PORT_NUM = 7
EXT_PORT_NUM = 2
USB3_PORT_BITMAP = 0xCA
[Usb Port 1]
DEV_BUS = B00:D21:F0
DEV_PORT = 1
[Usb Port 2]
DEV_BUS = B00:D21:F0
DEV_PORT = 3
[Usb Port 3]
DEV_BUS = B00:D21:F0
DEV_PORT = 2
[Usb Port 4]
DEV_BUS = B00:D21:F0
DEV_PORT = 6
[Usb Port 5]
DEV_BUS = B00:D21:F0
DEV_PORT = 5
[Usb Port 6]
DEV_BUS = B00:D19:F0
DEV_PORT = 2
[Usb Port 7]
DEV_BUS = B00:D19:F0
DEV_PORT = 1
[MMC Port 1]
DEV_BUS = B00:D27:F0
[Boot Enclosure]
VENDOR = QNAP
MODEL = BOOT
MAX_DISK_NUM = 1
[Boot Disk 1]
DISK_DRV_TYPE = MMC
DEV_BUS = B00:D28:F0
[System Memory]
MAX_CHANNEL_NUM = 2
MAX_SLOT_NUM = 2
SLOT1_ADDR = 1, 0x50
SLOT2_ADDR = 2, 0x52
