blindspot
-
Posts
43 -
Joined
-
Last visited
-
Days Won
1
Posts posted by blindspot
-
-
1 minute ago, pocopico said:
Ok with no SataPortMap ?
We have detected errors on the hard 1,2,4 drives and the SATA ports have also been disabled.
Please shut down your DS3617xs to replace or remove the hard drives and try again.
DiskStation> fdisk -l
Disk /dev/sde: 932 GB, 1000204886016 bytes, 1953525168 sectors
Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type
/dev/sde1 0,0,2 1023,255,63 1 4294967295 4294967295 2047G ee EFI GPTDisk /dev/synoboot: 3700 MB, 3879731200 bytes, 7577600 sectors
Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type
/dev/synoboot1 * 0,32,33 6,62,56 2048 100351 98304 48.0M 83 Linux/dev/synoboot2 6,62,57 15,205,62 100352 253951 153600 75.0M 83 Linux
/dev/synoboot3 15,205,63 130,138,8 253952 2097151 1843200 900M 83 Linux
same as SataPortMap=5 and DiskIdsMap=00
-
8 minutes ago, pocopico said:
Can you try SataPortMap=15 ?
SataPortMap=15 and DiskIdsMap=00
DiskStation> fdisk -l
Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type
/dev/synoboot1 * 0,32,33 6,62,56 2048 100351 98304 48.0M 83 Linux
/dev/synoboot2 6,62,57 15,205,62 100352 253951 153600 75.0M 83 Linux
/dev/synoboot3 15,205,63 130,138,8 253952 2097151 1843200 900M 83 Linux
DiskStation>It doesn't find any disk
-
6 minutes ago, blindspot said:
how to connect to dsm with telnet
http://DS_IP:5000/webman/start_telnet.cgi
Hmmm… can't reach this page
DS_IP took too long to respond
Could not open connection to the host, on port 23: Connect failed
-
13 minutes ago, pocopico said:
And when you telnet to DSM the fdisk -l what does it show ?
also i forgot to ask for an lsscsi from TC
lsscsi
[2:0:0:0] cd/dvd Slimtype DVD A DA8A6SH GAA2 /dev/sr0
[4:0:0:0] disk ATA HGST HTS721010A9 A3J0 /dev/sda
[5:0:0:0] disk USB DISK 2.0 PMAP /dev/sdbplease remind me how to connect to dsm with telnet.
-
1 minute ago, pocopico said:
Can you provide the output of lsscsi -Hv and lspci -nnq from TC ?
lsscsi -Hv
[0] ahci
dir: /sys/class/scsi_host//host0
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata1/host0
[1] ahci
dir: /sys/class/scsi_host//host1
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata2/host1
[2] ahci
dir: /sys/class/scsi_host//host2
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata3/host2
[3] ahci
dir: /sys/class/scsi_host//host3
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata4/host3
[4] ahci
dir: /sys/class/scsi_host//host4
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata5/host4
[5] usb-storage
dir: /sys/class/scsi_host//host5
device dir: /sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/host5lspci -nnq
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller [8086:0c04] (rev 06)
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [8086:0c01] (rev 06)
00:02.0 VGA compatible controller [0300]: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller [8086:0416] (rev 06)
00:03.0 Audio device [0403]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller [8086:0c0c] (rev 06)
00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI [8086:8c31] (rev 05)
00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 [8086:8c3a] (rev 04)
00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller [8086:8c20] (rev 05)
00:1c.0 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 [8086:8c10] (rev d5)
00:1c.2 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 [8086:8c14] (rev d5)
00:1c.3 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 [8086:8c16] (rev d5)
00:1f.0 ISA bridge [0601]: Intel Corporation HM86 Express LPC Controller [8086:8c49] (rev 05)
00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c03] (rev 05)
00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller [8086:8c22] (rev 05)
01:00.0 3D controller [0302]: NVIDIA Corporation GM107M [GeForce GTX 950M] [10de:139a] (rev a2)
03:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01)
04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTL8411B PCI Express Card Reader [10ec:5287] (rev 01)
04:00.1 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 12) -
3 minutes ago, pocopico said:
Can you please remove the SataPortMap from the linux line ?
SataPortMap removed and DiskIdsMap=00
-
Just now, Peter Suh said:
Can't I physically point to SataportMap = 1 leaving only one SSD or HDD? Do you happen to have a Sata CD-ROM drive?
on these settings, no hdd found. there is a sata odd connected.
i've tried
SataPortMap=1 and DiskIdsMap=00
SataPortMap=1 and DiskIdsMap=01
SataPortMap=1 and DiskIdsMap=02
SataPortMap=4 and DiskIdsMap=00
SataPortMap=3 and DiskIdsMap=00
SataPortMap=2 and DiskIdsMap=04
SataPortMap=3 and DiskIdsMap=00
no hdd found
-
Just now, Peter Suh said:
Since it's a laptop, I think there's a high possibility that there's no
It would be impossible to turn on the hot plug of Sata Port, right?
Also, are you trying with DSM 7.0.1 TinyCore?Dont have hotplug in bios settings. satamap now finds SataPortMap=5 and DiskIdsMap=00 but message says errors on hdd 1,2,4
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) (prog-if 01 [AHCI 1.0])
Kernel driver in use: ahci
-
Hello,
I have a ASUS X550J laptop and can't figure out sata map. It has 2 sata ports, one for hdd and one for odd, but the lspci says it has a 6-port sata controller.
The pic bellow is with sataportmap=6 and diskidxmap=00. If I set sataportmap=2 and diskidxmap=00 it says no hdd found. Any ideea? Thanks
-
30 minutes ago, Doud said:
ds918p_42661.pat decrypted is needed but the builded by rploader.sh is corrupt...
@Peter Suh and @loveburn They succeeded...
I hope someone gonna shared ds918p_42661.pat decrypted
I just did it like 30 min ago by running ./rploader.sh build apollolake-7.1.0-42661 and it decrypted fine.
14 minutes ago, phone guy said:this process to upgrade from dsm 7.0.1 ---> manual upgrade inside dsm using pat from synology, reboot to tc run these commands and reboot nas
Yes, tested and working.
-
39 minutes ago, Doud said:
If someone have one ds918p_42661.pat working it's possible to share please?
Thanks in advance!!
Download from Synology DS918+. I think it has to be the original one when you update from manual DSM update. That's how I did it. I've tried to use the cached one but didn't work.
-
17 minutes ago, maxhartung said:
Tried with broadwellnk-DS3622 same issue. Another ideea ? I will try with broadwell.
Have you tried
"SataPortMap": "1",
"DiskIdxMap": "02"sata controller might start from 02 if it shows sdb and sdd on fdisk -l
then you could try
"SataPortMap": "2",
"DiskIdxMap": "02"to be able to see both disks
-
6 minutes ago, maxhartung said:
Then I should have it. I will try a build. I have the latest from git. I just build bromolow but with serialgen 3622xs, right ?
apollolake-DS918
bromolow-DS3615
broadwell-DS3617
broadwellnk-DS3622 -
6 minutes ago, taiziccf said:
I am using proxmox, i have a question, what disk mapping do i need to set so that in DSM it will show Drive 1 instead of Drive 7?
thank you
My guess is that the first 6 drives are reserved for IDE. If you change from SATA to IDE it will show on Drive 1.
-
5 hours ago, ThorGroup said:
To our knowledge the absolute max is 26 as DSM doesn't support /dev/sdaa /dev/sdab /dev/sdac etc. naming. Since there's only 26 letters you can only use 26 disks. Their eboxes work differently and that's how on a real DS you can get >26 drives.
Maybe is not related but this is how DSM is showing drives on the second controller on my bare metal ASRock N3700 and is working fine.
-
I'm stuck at compiling redpill-lkm. Which sources should I use and from where? Thanks
-
Not possible atm. All attempts made so far are UNSUCCESSFUL. You have to wait for a new version of loader.
-
1
-
TinyCore RedPill Loader (TCRP)
in Loaders
Posted
Same sde
DiskStation> fdisk -l
Disk /dev/sde: 932 GB, 1000204886016 bytes, 1953525168 sectors
Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type
/dev/sde1 0,0,2 1023,255,63 1 4294967295 4294967295 2047G ee EFI GPT
Disk /dev/synoboot: 3700 MB, 3879731200 bytes, 7577600 sectors
Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type
/dev/synoboot1 * 0,32,33 6,62,56 2048 100351 98304 48.0M 83 Linux
/dev/synoboot2 6,62,57 15,205,62 100352 253951 153600 75.0M 83 Linux
/dev/synoboot3 15,205,63 130,138,8 253952 2097151 1843200 900M 83 Linux
this is usb config
linux /zImage withefi earlyprintk syno_hw_version=DS3617xs console=ttyS0,115200n8 netif_num=1 pid=0x4100 earlycon=uart8250,io,0x3f8,115200n8 syno_port_thaw=1 mac1=XXX sn=XXX vid=0x13fe elevator=elevator loglevel=15 HddHotplug=0 DiskIdxMap=00 syno_hdd_detect=0 vender_format_version=2 syno_hdd_powerup_seq=0 log_buf_len=32M root=/dev/md0 SataPortMap=5 Sata_Remap="5>0"