sandisxxx
-
Posts
104 -
Joined
-
Last visited
Posts posted by sandisxxx
-
-
- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.1.6-15266
- Loader version and model: JUN'S LOADER v1.02b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HP Gen8 Microserver
- Additional comments: NO REBOOT REQUIRED
-
- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.1.5
- Loader version and model: JUN'S LOADER v1.02b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: Microserver G8
- Additional comments: REBOOT REQUIRED
-
- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.1.4 15217 Update 5
- Loader version and model: Jun's Loader v1.02b - DS3617xs
- Installation Type: HP gen 8
- Additional comments: Reboot required
-
- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.1.4 15217 - Update 3
- Loader version and model: Jun's Loader v1.02b - DS3615xs
- Installation type: Baremetal (HPE Microserver Gen8)
- Additional comments: Requires reboot
-
Quoting, becuz my situation is pretty same:
ESXi v6.5.0 on HP Microserver Gen8 baremetal
1.02b Juns loader
DS3615xs
DSM 6.1.4-15217 Update 2 - OK
No reboot required
-
Bare metal HP Microserver Gen8, HP Stock Raid Controller - AHCI mode (no raid, every drive is a single volume), Jun's 1.02b loader, upgrade from previous latest ALL OK.
- 1
-
On 11/7/2017 at 12:23 PM, foxbat said:
UPDATE OK on bare metal ( hp) and esx6.5. ( from 6.1.3 u8)
Hi, thanks for posting, HP = Microserver Gen 8? Bootloader = Jun's 1.02b?
-
HP Microserver Gen8 Bare metal
Jun's loader 1.02b booting from internal USB
HP RAID Controller in AHCI Mode.
Web GUI update without any issues.
-
HP Microserver Gen8 Bare metal
Jun's loader (thanks Jun) 1.02b
Update from 6 to 7 without any issues.
-
4 hours ago, sandisxxx said:
I am running 15152 Update 5 with Jun's loader 1.02a on HP Microserver Gen8(stock RAID controller) bare metal.
Thanks for the info, going to update now and report the results.
In my case, also everything was OK. Even Docker container still works just fine.
-
5 hours ago, tabajdi said:
I have Hp gen 8 baremetal with Jun's 1.02b and uppdate to 6.1.3 15152 Update 6 works without any problem.
Sent from my SM-G930F using Tapatalk
I am running 15152 Update 5 with Jun's loader 1.02a on HP Microserver Gen8(stock RAID controller) bare metal.
Thanks for the info, going to update now and report the results.
-
Thanks all for the replies, especially jensmander.
Will give it a shot and I believe, with your instructions, it will be just fine.
Will try to report back when done.
I have also a testing VM for experiments, so first I will give it a try in the VM environment.
Cheers.
-
Hello community, I was googling for an hour now and was not able to find any guide how to upgrade from 6.0.2 to 6.1.X on my HP MS G8.
Using Jun's loader for the 6.0.2 booting from USB.
Please send me a link or advice, how I can upgrade without loosing the Config and Data.
Thanks
-
HP Microserver Gen8 baremetal upgrade from 9 to 11 no problems.
-
Thanks, now I wonder, what does Update 11 from update 9
There is a forum thread for update 11, so let;s hope the community will inform us how it went before we install.
-
Also Interested.
Running bare metal on HP Microserver Gen8.
please let us know who tested this.
-
Hello community, did anybody try Update 10 to Juno's loaded DSM 6.0.2-8451 bare metal?
Is it safe to proceed?
Please share your experience.
Thanks.
-
I'd recommend to use AHCI mode. In this settings, the RAID will be managed by DSM. If no RAID used, then also the Spin-down feature is working with Baremetal and Gen8 HP.
-
Great Idea!
The Raspi and other Pi and similar variants all use ARM processors and as such incompatible with EXP requiring X86/X64 processors.
But!
Not all SBCs are ARM based! As you mentioned, A Latte Panda(an Intel Atom based SBC) WOULD work, but I wouldn't recommend it. it is lacking in ports severely. (Plus some huge overheating problems iv seen)
If I were to try and do this, Id probably pick up one of the AMD/Intel Embedded processor motherboards from NewEgg (listing)
I personally like the options this one provides:
*Pretty cheap at ~$75
*DC barrel Plug that can run from 12 or 19 volts (Should allow you to use an old Laptop Powerbrick to run the thing)
*Uses DDR3 SODIMM memory for tiny form factor
*2 on-board SATAIII(6 Gb/s) ports
*Gigabit LAN
* Relativley powerful Dual-Core Celeron processor
*2 miniPCI ports
I think my favorite part is the 2 miniPCI ports. Why? because these exist which would allow you to add two extra SATAIII ports PER MiniPCI port!! (Also a half-length version is available if you wanted to add 2 SATA cards as one of the ports is full length and the other one is half length)
If you were to populate the two PCI connectors you could effectively use 6 Drives in the build
What a great reply to the topic.
I totally did not know about th mPCIEx / SATA3 cards.
EDIT: How is it about the dirvers, for example, does Junos 1.01 loader support those cards?
Thanks for this!
-
How is your SATA mode set in BIOS? Is it set to AHCI?
-
Hello, I'd recommend to try to use WakeOnLan software within the LAN to try to wake it up.
Of course it has to be allowed in BIOS or iLO.
If you can not make it work, maybe you can use another LAN cable and wake the server up by iLO web interface.
-
Thanks for suggestion, I have installed FFMpeg from the SynoCommunity and it looks it is workong now.
However the Celeron G1610T seems to be having trouble to transcode the FHD video with DTS audio.
It'100% CPU load and the playback is laggy.
But this can be considered as closed.
-
Bootloader : Jun 1.01 - great job and kudos to Juno
DSM : 6.0.2-8451 Update 9
bare metal
HP Microserver Gen8
8 GiB of RAM
Intel Celeron G1610T
Stock HP SATA/Raid Controller
1x WD 1TB SATA Disk
1x WD 2TB SATA Disk
1x 500GB SATA Disk for old stuff
Volume: Basic, each disk has it's own volume of the size of the whole disk
-
Hello community, I have HP Microserver Gen8 with Celeron G1610T CPU, running Junos loader DSM6 Update 9.
I have noticed, that in Video station, all movies with DTS audio do not play.
I have found, that I need to install FFMPEG package here:
https://nunobhorta.com/enable-ffmpeg-dt ... o-station/
I have downloaded the packages and there is plenty of them, depending on the original CPU in Synology NAS devices.
Please advice which package to install or how to make DTS audio movies play in DSM6 Video station.
Thanks.
HP Microservers above 6.2
in DSM 6.x
Posted · Edited by sandisxxx
Hello community. I have been really struggling yesterday after I (without research) updated from Jun's loade 1.02b DSM 6.1.X 3615sx to Jun's loader 1.03b and DSM DSM 6.2-23739 - HP Microserver Gen8 bare metal.
I migrated everything successfully and then hit the Update button (badum ts).
Then I figured that this is probably due to the internal NICs not being supported any more.
My NICs are Broadcom BCM5720.
I would like to have the latest DSM running, due to security patches and also due my Let's encrypt certificate.
It does not seem to work now with the older build.
Question: Is there ANY way how to make the Internal NICs work with the latest DSM or the only possible way is to get a supported NIC?
I was not really able to find any solution for this, just putting in a PCIEx NIC.
And if the PCIEx NIC is the only possible way, do you have specific NIC models as well as some advice, how to perform this on an existing DSM 6.2-23739 bare metal installation?
THanks