UNSC-117
-
Posts
108 -
Joined
-
Last visited
Posts posted by UNSC-117
-
-
No Hard Drive Found I'm thinking no drivers for my raid card. Could you point me or help me to load drivers in to boot.img
3Ware 9690SA-8I 512MB SAS SATA PCIe x8 RAID Controller
-
My server is currently expanding the pool, my question is what would happen if power fails or I shut it down.
The reason for this question is since I'm in FL Orlando tomorrow we have the hurricane most likely we would lose power
-
Has anyone got it working?
-
I have changed the bios to AHCI-Mode and am still having the same issue. The error is still saying failed to apply settings.
One message I just noticed is a system event warning - Abnormality detected. All volumes have been unmounted.
I think the next step is to test all the drives are working correctly.
Check sata cables swap Working HD's connect them where the ones don't work see if the working show up. Upgrade Bios or downgrade. Try a sata card if you have one Reinstall maybe bad install.
Hope this help good luck.
-
Still going strong just added a 4th 5tb hard drive. Expanding at the moment.
-
Let me know how it goes? which one was it? The one i got was very cheap. i paid like 25 bucks
Thanks!Good to know
it's great to have these type of feedback
I also ordered a new 16 port SATA3 card, I'm hoping it works without problems.
I'll update once It arrives and get it installed
-
Just wanted to let you guys know this sata card supports 5TB HD. No firmware upgrades
-
Fresh install? or upgrade? could you provide some sort of guide plz thanks.
Maybe is been asked.Baremetal install successful??
Probably has but I've read all 40 pages a few different times and didn't see any mention. Maybe mkdir will work I will test later. Yes baremetal install. Works great with a few modifications on Intel Nuc.
-
Maybe is been asked.
Baremetal install successful??
-
-
I got it working the first day it was out. on bare metal. but like eveyone said can't crate volumes. this is the problem we are all facing when updating thru Synology control panel and no new xpenoboot.
I got DSM 6 working on a PC, not VM.The only way I got it:
1. Restore default configuration, in a installed 5.2-5644 PC system.
2. Boot with Xpenoboot 5.2-5644 USB pendrive
3. Access web for first config, but not use "manual installation", I choose "install now".
4. After several minutes downloading from synology, the system reboots with actual DSM 6.0.1-7393.
I don't know if people can't update their systems or the problems about upgrading are VMs (VMware, ESXi) related.
For now, the only service that doesn't work is "Resource Monitor", if open a message about network error appears, and close automatically.
Thanks for the Xpenology community and developers!!!
-
If it is plug and play any hardware i would pay around $50-$75. Depends on support.
-
Reboot Server
-
-
-
-
http://www.ebay.com/itm/230990887722?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Works like a charm and it supports 3TB Hd the one your looking at doesn't
Problem is :
Price : US $35.00 Approximately ZAR 533.29 <--- which is fine
Shipping to south africa : $60.00 (approx. ZAR 914.22) <--- which is insane.
would rather try flash the ones i have.
I see
-
-
http://www.ebay.com/itm/230990887722?_t ... EBIDX%3AIT
Works like a charm and it supports 3TB Hd the one your looking at doesn't
-
-
Same thing happened to me me i believe it has to be larger than 8gb
-
I have a 6700k on my main pc. I can try to run it if you don't get an asnwer
-
-
AMCC 3Ware 9690SA-8I Cheap and works like a charm holds 8 disk
DSM 6.1.x Loader
in Loaders
Posted
Need driver for:
3Ware 9690SA-8I 512MB SAS SATA PCIe x8 RAID Controller
Can any one load or point me on how to load them into the .img
The latest XPEnoboot dsm 5.XX .img had the drivers already.
Thank you