DarkBlade Posted December 31, 2022 Share #1 Posted December 31, 2022 (edited) I can get a basic build working following the tutorial here wundertech.net how-to-install-xpenology-on-proxmox-dsm-7 This gets DSM running on the Proxmox storage drive. I'm now trying to rebuild (from scratch), passing an Adaptec 72405 (24 port card set to HBA mode) through - hoping that DSM will still install on the VM drive and the disks on the Adaptec card are then seen as additional storage (to create storage pools etc). I only need/want to use (the first) 20 ports on the card (the remaining 4 ports are not connected to any drives or backplane). When booting into Redpill and DSM: DSM fails to spot the 20G VM disk The drives on the Adaptec card start from slot 3 Only 14 of the 15 drives I currently have installed are picked up. My initial attempts at changing the SataPortMap, DiskIdxMap and MaxDisks values has resulted in no disks showing, or crashing the Adaptec card. (requiring a complete power down to recover on one occasion). I've had a few other issues which I think I have now resolved. My ask is: How can I get the build working using the VM sata1 drive? What values should I try for SataPortMap, DiskIdxMap and MaxDisks? This is the hardware setup in Proxmox This is the satamap output (I manually set maxdisks to 24 in user_config before running satamap) Spoiler tc@box:~$ ./rploader.sh satamap now Machine is VIRTUAL Hypervisor=KVM Found SCSI HBAs, We need to install the SCSI modules scsi-5.10.3-tinycore64 is already installed! Succesfully installed SCSI modules Found "00:1f.2 Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02)" Detected 6 ports/0 drives. Mapping KVM q35 bogus controller after maxdisks Found "06:07.0 Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02)" Detected 6 ports/2 drives. Mapping SATABOOT drive after maxdisks WARNING: Other drives are connected that will not be accessible! Found SCSI/HBA "01:00.0 Adaptec Series 7 6G SAS/PCIe 3 (rev 01)" (15 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid bus number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) Found SCSI/HBA "06:07.0 Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02)" (8 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) Found SCSI/HBA "05:03.0 Red Hat, Inc. QEMU PCI-PCI bridge 06:03.0 Red Hat, Inc Virtio memory balloon" (81 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) lspci: -s: Invalid slot number Found SCSI/HBA "" (0 drives) Computed settings: SataPortMap=11 DiskIdxMap=1818 Edited December 31, 2022 by DarkBlade Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.