Try install DS3615xs/DS3617xs 6.1/2 on intel D2500CC mobo


Recommended Posts

Hello, i try install at last 7 days... DSM 6.1/2 on mobo intel D2500CC no visable on Synology Assistant, it's work without problem on 5.2 version.

 

Spec : 

D2500CC (last bios 0040)

Intel Atom D2500

Intel NM10 Express

Dual Gigabit LAN Intel 82574L   (Ven: 8086, Dev: 10D3 - 82574L)

4GB DDR 3 1066Mhz

2 Port SATA NM10/ICH7 + extra 4 Port SATA III Mini Pci-E SI-MPE40125 IO Crest (88SE9215 PCIe?)

(4x4TB RED WD, but i try 4 another hard drivrs and SSD drivers)

 

I try loaders (DS3615xs/DS3617xs) 1.01, 1.02, 1.02MBR, 1.03b and 1.04b but no one work for me ;/ I try mbr versions, i change files extra.lzma, zImage, rd.gz, different configurations i try UEFi off, on, one LAN ON, second LAN ON... loaders boot from USB at UEFi OFF, but find.synology.com , and Synology Assistant not see that mobo Intel D2500CC, i see the IP adress on me network , ping ok, but cannot entry form web. Of course i set VID/PID for USB stick, and MAC adress for one , or two LAN. I try another router, another PC and nothing ;/ 

 

I found one user on that intel mobo who success install DSM 6.2.2-24922 Update 4, on this TOPIC

 

What i doo wrong ? Only one thing is suspect for me, USB stick (i try 3 different, and in USB-HDD, USB-FDD, UZB-ZIP mode) is visable in bios like hard drive, not removable drive, its that normal ?

 

Form SSH DSM 5.2  :

 

Spoiler

DiskStation> lspci -k | grep 'Kernel driver'
        Kernel driver in use: pcieport
        Kernel driver in use: pcieport
        Kernel driver in use: pcieport
        Kernel driver in use: uhci_hcd
        Kernel driver in use: uhci_hcd
        Kernel driver in use: uhci_hcd
        Kernel driver in use: uhci_hcd
        Kernel driver in use: ehci-pci
        Kernel driver in use: lpc_ich
        Kernel driver in use: ahci
        Kernel driver in use: e1000e
        Kernel driver in use: ahci

DiskStation> ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 00:22:4D:AD:F1:FD
          inet addr:192.168.1.234  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::222:4dff:fead:f1fd/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:25950 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12987 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:31726997 (30.2 MiB)  TX bytes:4277402 (4.0 MiB)
          Interrupt:17 Memory:d0120000-d0140000


DiskStation>lspci -k
00:00.0 Class 0600: Device 8086:0bf5 (rev 04)
        Subsystem: Device 8086:202c
00:02.0 Class 0300: Device 8086:0be1 (rev 0b)
        Subsystem: Device 8086:202c
00:1c.0 Class 0604: Device 8086:27d0 (rev 02)
        Kernel driver in use: pcieport
00:1c.1 Class 0604: Device 8086:27d2 (rev 02)
        Kernel driver in use: pcieport
00:1c.2 Class 0604: Device 8086:27d4 (rev 02)
        Kernel driver in use: pcieport
00:1d.0 Class 0c03: Device 8086:27c8 (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: uhci_hcd
00:1d.1 Class 0c03: Device 8086:27c9 (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: uhci_hcd
00:1d.2 Class 0c03: Device 8086:27ca (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: uhci_hcd
00:1d.3 Class 0c03: Device 8086:27cb (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: uhci_hcd
00:1d.7 Class 0c03: Device 8086:27cc (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: ehci-pci
00:1e.0 Class 0604: Device 8086:2448 (rev e2)
00:1f.0 Class 0601: Device 8086:27bc (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: lpc_ich
00:1f.2 Class 0106: Device 8086:27c1 (rev 02)
        Subsystem: Device 8086:202c
        Kernel driver in use: ahci
00:1f.3 Class 0c05: Device 8086:27da (rev 02)
        Subsystem: Device 8086:202c
02:00.0 Class 0200: Device 8086:10d3
        Subsystem: Device 8086:202c
        Kernel driver in use: e1000e
03:00.0 Class 0106: Device 1b4b:9215 (rev 11)
        Subsystem: Device 1b4b:9215
        Kernel driver in use: ahci


DiskStation> lspci -q
00:00.0 Host bridge: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controlle                                                    r (rev 04)
00:02.0 VGA compatible controller: Intel Corporation Atom Processor D2xxx/N2xxx                                                     Integrated Graphics Controller (rev 0b)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 0                                                    2)
00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 0                                                    2)
00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 0                                                    2)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #                                                    1 (rev 02)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #                                                    2 (rev 02)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #                                                    3 (rev 02)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #                                                    4 (rev 02)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller                                                     (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation NM10/ICH7 Family SATA Controller [AHC                                                    I mode] (rev 02)
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02)
02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
03:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9215 PCIe 2.0 x1 4-po                                                    rt SATA 6 Gb/s Controller (rev 11)
pcilib: Cannot write to /var/services/homes/admin/.pciids-cache: No such file or                                                     directory


DiskStation> uname -a
Linux DiskStation 3.10.35 #1 SMP Sun Jul 17 16:02:22 CEST 2016 x86_64 GNU/Linux synology_bromolow_3615xs
DiskStation>


DiskStation> ethtool -i
ethtool: bad command line argument(s)
For more information run ethtool -h
DiskStation> ethtool -i
ethtool: bad command line argument(s)
For more information run ethtool -h
DiskStation> ethtool -i eth0
driver: e1000e
version: 3.3.3-NAPI
firmware-version: 2.1-2
bus-info: 0000:02:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no


 lspci -v
00:00.0 Class 0600: Device 8086:0bf5 (rev 04)
        Subsystem: Device 8086:202c
        Flags: bus master, fast devsel, latency 0

00:02.0 Class 0300: Device 8086:0be1 (rev 0b)
        Subsystem: Device 8086:202c
        Flags: bus master, fast devsel, latency 0, IRQ 11
        Memory at d0200000 (32-bit, non-prefetchable) [size=1M]
        I/O ports at 30d0 [size=8]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: <access denied>

00:1c.0 Class 0604: Device 8086:27d0 (rev 02)
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00004000-00004fff
        Memory behind bridge: d0400000-d05fffff
        Prefetchable memory behind bridge: 00000000d0600000-00000000d07fffff
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:1c.1 Class 0604: Device 8086:27d2 (rev 02)
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: d0100000-d01fffff
        Prefetchable memory behind bridge: 00000000d0800000-00000000d09fffff
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:1c.2 Class 0604: Device 8086:27d4 (rev 02)
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 00001000-00001fff
        Memory behind bridge: d0000000-d00fffff
        Prefetchable memory behind bridge: 00000000d0a00000-00000000d0cfffff
        Capabilities: <access denied>
        Kernel driver in use: pcieport

00:1d.0 Class 0c03: Device 8086:27c8 (rev 02)
        Subsystem: Device 8086:202c
        Flags: bus master, medium devsel, latency 0, IRQ 23
        I/O ports at 30a0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.1 Class 0c03: Device 8086:27c9 (rev 02)
        Subsystem: Device 8086:202c
        Flags: bus master, medium devsel, latency 0, IRQ 19
        I/O ports at 3080 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.2 Class 0c03: Device 8086:27ca (rev 02)
        Subsystem: Device 8086:202c
        Flags: bus master, medium devsel, latency 0, IRQ 18
        I/O ports at 3060 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.3 Class 0c03: Device 8086:27cb (rev 02)
        Subsystem: Device 8086:202c
        Flags: bus master, medium devsel, latency 0, IRQ 16
        I/O ports at 3040 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.7 Class 0c03: Device 8086:27cc (rev 02) (prog-if 20)
        Subsystem: Device 8086:202c
        Flags: bus master, medium devsel, latency 0, IRQ 23
        Memory at d0300400 (32-bit, non-prefetchable) [size=1K]
        Capabilities: <access denied>
        Kernel driver in use: ehci-pci

00:1e.0 Class 0604: Device 8086:2448 (rev e2) (prog-if 01)
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
        Capabilities: <access denied>

00:1f.0 Class 0601: Device 8086:27bc (rev 02)
        Subsystem: Device 8086:202c
        Flags: bus master, medium devsel, latency 0
        Capabilities: <access denied>
        Kernel driver in use: lpc_ich

00:1f.2 Class 0106: Device 8086:27c1 (rev 02) (prog-if 01)
        Subsystem: Device 8086:202c
        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 43
        I/O ports at 30c8 [size=8]
        I/O ports at 30dc [size=4]
        I/O ports at 30c0 [size=8]
        I/O ports at 30d8 [size=4]
        I/O ports at 3020 [size=16]
        Memory at d0300000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: <access denied>
        Kernel driver in use: ahci

00:1f.3 Class 0c05: Device 8086:27da (rev 02)
        Subsystem: Device 8086:202c
        Flags: medium devsel, IRQ 9
        I/O ports at 3000 [size=32]

02:00.0 Class 0200: Device 8086:10d3
        Subsystem: Device 8086:202c
        Flags: bus master, fast devsel, latency 0, IRQ 17
        Memory at d0120000 (32-bit, non-prefetchable) [size=128K]
        Memory at d0100000 (32-bit, non-prefetchable) [size=128K]
        I/O ports at 2000 [size=32]
        Memory at d0140000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: e1000e

03:00.0 Class 0106: Device 1b4b:9215 (rev 11) (prog-if 01)
        Subsystem: Device 1b4b:9215
        Flags: bus master, fast devsel, latency 0, IRQ 44
        I/O ports at 1028 [size=8]
        I/O ports at 1034 [size=4]
        I/O ports at 1020 [size=8]
        I/O ports at 1030 [size=4]
        I/O ports at 1000 [size=32]
        Memory at d0000000 (32-bit, non-prefetchable) [size=2K]
        Expansion ROM at d0a00000 [disabled] [size=256K]
        Capabilities: <access denied>
        Kernel driver in use: ahci
 

 

 

 

Edited by procsacs
Link to post
Share on other sites

First: Disable the extra 4 Port SATA III Mini Pci-E SI-MPE40125 IO Crest (88SE9215 PCIe?).


Second: In the BIOS, disconnect the second network card.


Third: Write the address of the first network card in the MAC grab.

 

Install bootloader DS3615xs - 1.03b.


Install the system with one HDD connected to SATA Port NM10 / ICH7

 

Take a photo of the BIOS settings and send it to me through the file hosting service fex.net

 

Unfortunately, I installed xpenology on the D2500CC for tests and system evaluation and later preinstalled on a more powerful system. But the board still remains, so I can try to raise it again.

Edited by AlexChu
Link to post
Share on other sites
Posted (edited)

Thank you for the answer, you managed to install it in THIS topic, as I understood correctly, you turned off the second network card, and turned on UEFi?

 

Here is bios photo

 

I try without 4 port SATA Mini Pci-E, but no positive result ;/ For test i connected one, or two empty hard disk, no success. On loader 1.03b (DS3615xs)  I can see IP adress on network, but no work form WEB, or synology assistance.

Edited by procsacs
Link to post
Share on other sites

Is the SSD kingston empty? Delete the partitions on it.

It is very strange that you see the IP on the network but the web does not work.

Scan your network with the program

 

scaner

 

and show the screen.

Link to post
Share on other sites
Posted (edited)

Disk empty, no partition i try 4 different HDD and SDD, GPT, MBR etc...

 

photo from IP  and PING

 

in THIS topic, you turned off the second network card, and turned ON UEFi? When i turn ON UEFi i have no IP adress in scaner. 

 

Me config in grub.cfg, mac1=00224DADF1FD it's me first LAN card, i try to turn OFF first, and ON second witch second MAC adress but still this sam situation  :

 

Spoiler

if serial --port=0x3F8 --speed=115200;then
        set has_serial=true
        terminal_input --append serial
        terminal_output --append serial
else
        clear
fi

terminal_input --append console
terminal_output --append console

if [ x"${grub_platform}" = xefi ]; then
        insmod efi_gop
        insmod efi_uga
else
        insmod vbe
fi

set extra_initrd="extra.lzma"
set info="info.txt"

set vid=0x13fe
set pid=0x4100
set sn=1230LWN028723
set mac1=00224DADF1FD
set rootdev=/dev/md0
set netif_num=1
set extra_args_3615=''
#set extra_args_3615='earlycon=uart8250,io,0x3f8,115200n8 earlyprintk loglevel=15'

set common_args_3615='syno_hdd_powerup_seq=0 HddHotplug=0 syno_hw_version=DS3615xs vender_format_version=2 console=ttyS0,115200n8 withefi elevator=elevator quiet syno_port_thaw=1'

set sata_args='sata_uid=1 sata_pcislot=5 synoboot_satadom=1 DiskIdxMap=0C SataPortMap=1 SasIdxMap=0'

set default='0'
set timeout='1'
set fallback='1'

if [ -s $prefix/grubenv ]; then
        load_env
        if [ -n "$saved_entry" ]; then
                set default="${saved_entry}"
        fi
fi

VERSION="with Jun's Mod v1.03b"

search --file -s /bzImage

function savedefault {
        if [ -s $prefix/grubenv  ]; then
                saved_entry="${chosen}"
                save_env saved_entry
        fi
}

function do_option {
        if [ $# -lt 2 ]; then
                eval "set value=\"\$$1\""
                echo "current $1: $value"; return;
        fi
        set key=$1
        shift
        set $key="$*"
        if [ -s $prefix/grubenv  ]; then
                save_env $key
        fi
}

function vid { do_option vid $@; }
function pid { do_option pid $@; }
function sn { do_option sn $@; }
function mac1 { do_option mac1 $@; }
function mac2 { do_option mac2 $@; }
function mac3 { do_option mac3 $@; }
function mac4 { do_option mac4 $@; }
function rootdev { do_option rootdev $@; }
function append { do_option extra_args_3615 $@; }

function vidpid {
        if [ $# -lt 2 ]; then
                echo "usage: vidpid 0xVVVV 0xPPPP"; return;
        fi
        set usb_args="vid=$1 pid=$2"
        if [ -s $prefix/grubenv  ]; then
                save_env usb_args
        fi
}

function showtips {
        if [ -n "$has_serial" ]; then
                terminal_output --remove serial
        fi
        echo "Screen will stop updating shortly, please open http://find.synology.com to continue."
        echo
        echo
        if [ -n "$has_serial" ]; then
                terminal_output --append serial
        fi
}

function loadinitrd {
        if [ -s $img/$info ]; then
                if [ -n "$has_serial" ]; then
                        terminal_output --remove serial
                fi
                cat $img/$info
                if [ -n "$has_serial" ]; then
                        terminal_output --append serial
                fi
        fi
#        if [ -s $img/$extra_initrd ]; then
#                initrd $img/rd.gz $img/$extra_initrd
#        else
#                initrd $img/rd.gz
#        fi
}

function common_add_option {
        eval "set value=\"\$$1\""
        if [ -z $value ]; then return 1; fi
        set common_args="$common_args $1=$value"
}

function common_add_option_ex {
        eval "set value=\"\$$1\""
        if [ -z $value ]; then return 1; fi
        set common_args="$common_args $2=$value"
}

function loadlinux {
        set model=$1
        set bootdev=$2
        shift 2
        if [ -n $vid -a -n $pid ]; then
                set usb_args="vid=$vid pid=$pid"
        fi
        eval "set common_args=\"\$common_args_$model\""
        eval "set extra_args=\"\$extra_args_$model\""
        eval "set bootdev_args=\"\$${bootdev}_args\""
        common_add_option_ex rootdev root
        common_add_option sn
        if common_add_option mac1; then set netif_num=1; fi
        if common_add_option mac2; then set netif_num=2; fi
        if common_add_option mac3; then set netif_num=3; fi
        if common_add_option mac4; then set netif_num=4; fi
        common_add_option netif_num
    if [ -z $zImage ]; then
        set zImage=bzImage
    fi
        linux $img/$zImage $common_args $bootdev_args $extra_args $@
}

menuentry "DS3615xs 6.2 Baremetal $VERSION" --class os {
        set img=
        savedefault
        loadlinux 3615 usb
        loadinitrd
        showtips
}

menuentry "DS3615xs 6.2 Baremetal $VERSION Reinstall" --class os {
        set img=
        loadlinux 3615 usb mfg
        loadinitrd
        showtips
}

#menuentry "DS3615xs 6.2 Baremetal AMD $VERSION" --class os {
#        set img=
#        set zImage=bzImage
#        savedefault
#        loadlinux 3615 usb
#        loadinitrd
#        showtips
#}

menuentry "DS3615xs 6.2 VMWare/ESXI $VERSION" --class os {
        set img=
        savedefault
        loadlinux 3615 sata
        loadinitrd
        showtips
}
 

 

Edited by procsacs
Link to post
Share on other sites
1 hour ago, AlexChu said:

Try this image

 

img

 

I still have the motherboard and I will try to raise the system on it and unsubscribe. Wait a day or two

 

 

Still that same, adress IP on network but no work ;/ OK i will wait, thanks so much !!!

Link to post
Share on other sites

I tried to install version 3615 on the D2500CC board, but I got the same picture as yours: the ip is lit on the network but it can't connect. I could not remember the correct boot parameters.

The minimum version for this MiniDLNA is 6.2.4-0000, you have 6.2.2 installed

Link to post
Share on other sites
Posted (edited)

hmm interesing it's just a BIOS setup ? Or you change something in img file ? 

 

MiniDLNA work in old DSM version, but you need good version of MiniDLNA (platform version) i get for DS1019+ and work of in DSM 6.2.2.

 

I am currently using at DS1019+ version, but I don't know how reliable the system is, it doesn't install updates.  It's work ok.

Edited by procsacs
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.