ZeroQI Posted April 2, 2015 #1 Posted April 2, 2015 Hi, i tried an h200 P19 but xpenoboot freeze while loading an usb3 driver module (xhci_hcd)... using a LSI 9240-8i reflashed in 9211-8i P19 works but if i enable SSH network stops (can from the console pint the local ip and hostname but cannot ping the gateway). same if i copy from the raid 5 (8x4tb hitachi nas) to the raid 5, it loose the ping from my desktop to the nas straight away, while i can copy from and to the nas without issues.... Motherboard: Asus H81I-PLUS (can somebody with the same motherboard post their dmesg log "dmesg > /volume1/video/dmesg.txt") 2x4GB ram crucial (tried with a single dimm, same thing) Case: NSC-800 PSU: Seasonic 250w flex atx + adaptor plate Controller: LSI 9240-8i + 40mm fan + sata to fan connector Dunno what to do... What's the best way to troubleshoot? tried 3 different usb keys as i thought they were defective... Dmesg [ 36.639190] ACPI: resource 0000:00:1f.3 [io 0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f] [ 38.699185] ACPI: resource 0000:00:1f.3 [io 0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f] [ 40.708597] ACPI: resource 0000:00:1f.3 [io 0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f] [ 42.717890] ACPI: resource 0000:00:1f.3 [io 0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f] [ 45.817183] r8169 0000:04:00.0: eth0: link up What does the below mean? [ 96.619377] Pid: 19250, comm: scemd Tainted: P C O 3.2.40 #1 ASUS Synoden/H81I-PLUS [ 96.619379] RIP: 0010:[] [] ahci_sw_locate_set.isra.17+0x3c/0xd0 [ 96.619382] RSP: 0018:ffff880200a07c18 EFLAGS: 00010202 [ 96.619383] RAX: 0000000000000000 RBX: 0000000000000048 RCX: 0000000000000000 [ 96.619384] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880213064000 [ 96.619385] RBP: ffff880200a07c38 R08: 0000000000000000 R09: 0000000000000000 [ 96.619386] R10: ffff880200a06000 R11: 0000000000000000 R12: ffff880213064000 [ 96.619387] R13: 0000000000000002 R14: ffff880213064000 R15: ffff880213065f48 [ 96.619388] FS: 0000000000000000(0000) GS:ffff88021fb00000(0063) knlGS:00000000f4aebb70 [ 96.619389] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033 [ 96.619390] CR2: 0000000000000098 CR3: 0000000201306000 CR4: 00000000000406e0 [ 96.619391] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 96.619392] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 96.619393] Process scemd (pid: 19250, threadinfo ffff880200a06000, task ffff88021e981280) [ 96.619394] Stack: [ 96.619395] 0000000000000001 ffff880213065c40 0000000000000000 0000000000000000 [ 96.619397] ffff880200a07c88 ffffffff81320ac1 ffff880200a07c68 ffff880213657000 [ 96.619398] ffff880200a07c78 ffffffffffffffff 00000000ffffffea ffff8802114e9080 [ 96.619400] Call Trace: [ 96.619402] [] sata_syno_ahci_diskled_set+0xc1/0x110 [ 96.619406] [] SetSCSIHostLedStatusByAHCIGPIO+0x14/0x60 [bromolow_synobios] [ 96.619408] [] ? synobios_ioctl+0xe6a/0xff0 [bromolow_synobios] [ 96.619411] [] ? path_lookupat+0xc1/0x9c0 [ 96.619413] [] ? putname+0x2e/0x40 [ 96.619414] [] ? user_path_at_empty+0x63/0xa0 [ 96.619416] [] ? do_vfs_ioctl+0xb4/0x8b0 [ 96.619419] [] ? do_page_fault+0x19c/0x480 [ 96.619422] [] ? compat_sys_ioctl+0x138/0x1640 [ 96.619424] [] ? vfs_stat+0x16/0x20 [ 96.619426] [] ? sys32_stat64+0x1b/0x40 [ 96.619429] [] ? do_munmap+0x1db/0x3d0 [ 96.619431] [] ? sysenter_dispatch+0x7/0x27 [ 96.619431] Code: e0 07 48 89 e5 41 55 41 89 f5 48 29 c8 41 c1 e5 08 41 54 49 89 fc 53 48 83 ec 08 48 8b 8f 70 2f 00 00 44 0b 6f 28 48 8d 5c 01 48 <48> 8b 43 50 48 89 53 60 48 8b 7f 10 25 00 00 ff ff 49 09 c5 e8 [ 96.619447] RIP [] ahci_sw_locate_set.isra.17+0x3c/0xd0 [ 96.619449] RSP [ 96.619449] CR2: 0000000000000098 [ 96.619451] ---[ end trace 397f1690528aa926 ]--- sata_syno_ahci_diskled_set? tried removing sata 2.5" disk on motherboard, same freeze. tried switching from ahci to compatible ide but only saw 3 disks from my raid then...
ZeroQI Posted April 5, 2015 Author #2 Posted April 5, 2015 i played with dmesg and managed to not use dummy sata ports using internalportcfg and enable bios settings, dmesg seemed better but the issue is still present... I tried including testmem in syslinux menu but it can't load com32 file (not com32r so prob 3.x version but not 4+) Since ssh give the same ping no longer working (box can ping itself by ip and name but no more network ping works) i can only assume the realtek 8168 driver crash, but the asus h81i-plus uses RTL8111G which uses r8168 driver [ 1.399860] r8168 Gigabit Ethernet driver 8.038.00 loaded [ 1.399882] r8168 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.399899] r8168 0000:04:00.0: setting latency timer to 64 [ 1.399976] r8168 0000:04:00.0: irq 45 for MSI/MSI-X [ 1.412782] eth%d: 0xffffc900044b8000, bc:ee:7b:5d:e1:26, IRQ 4 crash was induced by ssh after a day or copy through samba from the nas raid 5 to the nas raid 5 (same volume), reading from or writing to was ok While i could reproduce and crash on demand i no longer can so must be resolved last thing i did was the rmmod=r8169 insmod=r8168 Did use gateone (changed default ssh port) and run "dmesg > /volume1/video/dmesg-seem-working.txt" to create dmesg dump and check boot settings, opened with windows wordpad, saved, then opened with notepad to solve the line feed issue. Command line: BOOT_IMAGE=/zImage root=/dev/md0 ihd_num=0 netif_num=4 syno_hw_version=DS3615xs sn=B3J4N01003 vid=0x1221 pid=0x3234 loglevel=0 vga=0x305 libata.noacpi=1 rmmod=r8169 insmod=r8168 libata.noacpi=1 to solve messages and error i got pointing to ahci and/or acpi rmmod=r8169 insmod=r8168 to use old driver
Recommended Posts