menace
-
Posts
9 -
Joined
-
Last visited
Posts posted by menace
-
-
20 hours ago, Peter Suh said:
If you can access the DSM installation request screen with ttyd as below,
Then send me the log with the command you see.
http://<youripaddr>:7681/
id : root / pw : ( no password )
cat /var/log/junior_reason
cat /var/log/*rc*
SynologyNAS login:
SynologyNAS login: rootSynology strongly advises you not to run commands as the root user, who has
the highest privileges on the system. Doing so may cause major damages
to the system. Please note that if you choose to proceed, all consequences are
at your own risk.BusyBox v1.30.1 () built-in shell (ash)
SynologyNAS> cat /var/log/junior_reason
Exit on error [99] rp ext init exec failure...
SynologyNAS> cat /var/log/*rc*
START /linuxrc.syno.impl
Insert Marvell 1475 SATA controller driver
Insert basic USB modules...
:: Loading module usb-common ... [ OK ]
:: Loading module usbcore ... [ OK ]
:: Loading module ehci-hcd ... [ OK ]
:: Loading module ehci-pci ... [ OK ]
:: Loading module xhci-hcd ... [ OK ]
:: Loading module xhci-pci ... [ OK ]
:: Loading module usb-storage ... [ OK ]
:: Loading kernel modules from extensions ...
Loading kmod #0 "dca.ko" for pocopico.igb (args: )
Loading kmod #1 "igb.ko" for pocopico.igb (args: )
Loading kmod #0 "udp_tunnel.ko" for pocopico.ixgbe (args: )
Loading kmod #1 "ip6_udp_tunnel.ko" for pocopico.ixgbe (args: )
Loading kmod #2 "dca.ko" for pocopico.ixgbe (args: )
insmod: can't insert 'dca.ko': File exists
ERROR: kernel extensions "dca.ko" from pocopico.ixgbe failed to load
Exit on error [99] rp ext init exec failure...
Tue Apr 19 05:51:45 UTC 2022
none /sys/kernel/debug debugfs rw,relatime 0 0
SynologyNAS>
Thanks for your help
-
Hi
I have been using DS3622xs DSM 7.0.1-42218 for many weeks now without any errors. (Baremetal)
I decided to upgrade to DSM 7.1.0-42661 using the process as described in this thread. I don't have any errors in the build process. Once rebooted, I have no problems accessing the Synology install screen.
However, once the install completes, it reboots and goes directly back into the install screen again! This happens over and over.
I decided to wipe all my drives (I have backup!) And start from scratch. However, I still run into the same problem! (Installation loop)
Do you have any idea of what is going on? What commands do I need from the telnet screen to find out what is happening?
Thanks in advance
-
Hi
you have inadvertently left out DS3622 DSM 7.0.1-42218 in your rp-ext.json file for Atlantic (Marvell drivers)
the TAR file and set up file are in the releases directory.Could you please correct?
Thank you
- 1
-
On 2/20/2022 at 4:11 PM, menace said:
Could I please request a module for Solarflare SFN7122f 10 Gb network card for both 918+ and 3622xs?
I have DSM 7.0.1 918+ working right now on my Asrock E3C232D2l motherboard but would also like to test 3622XS.
Result from lspci:
0000:01:00.0 Ethernet controller [0200]: Solarflare Communications SFC9120 10G Ethernet Controller [1924:0903] (rev 01)RPM is available at:
https://support-nic.xilinx.com/wp/driversThanks
Please create a module for 918+ DSM 6.2.4
the current SFC module in the repository does not support this particular network card.Thanks very much
-
On 2/24/2022 at 9:10 PM, menace said:
Getting this error when trying to install Solarflare SFN7122f for 918+ 6.2.4
It appears that the file "i2c-algo-bit.ko" has been left out of the tar file. Is it possible to get this corrected?
Thank you very much. Sorry for all the duplicate posts. I cannot figure out how to delete a post!
-
-
-
21 hours ago, pocopico said:
Done ..
Many thanks! Now to do some testing
-
Could I please request a module for Solarflare SFN7122f 10 Gb network card for both 918+ and 3622xs?
I have DSM 7.0.1 918+ working right now on my Asrock E3C232D2l motherboard but would also like to test 3622XS.
Result from lspci:
0000:01:00.0 Ethernet controller [0200]: Solarflare Communications SFC9120 10G Ethernet Controller [1924:0903] (rev 01)RPM is available at:
https://support-nic.xilinx.com/wp/driversThanks
TinyCore RedPill Loader (TCRP)
in Loaders
Posted
Brilliant! Thank you so much! Worked straight away using the "manual" command.
I had to modify "synoinfo.conf" to enable SHR when using the "manual" command
Did you have have to add the IXGBEVF ext to get SR-IOV functionality? It does not seem to be installed by default.