sojab0on
-
Posts
43 -
Joined
-
Last visited
Posts posted by sojab0on
-
-
Just now, Unregistrado said:
My harddrives came from an DS918+ 6.2 and went into a DS3615XS 7.0.1. I also got the warning that it would reformat my disks when I wanted to fix the volume so certainly don’t do this. But when you check the pool, it found the pool. It recognised it as a raid 1 and I just had to restore the pool and it automatically finds the volume. I forgot to printscreen it. I will check if I can find a way to recreate it and will send a printscreen. Because I am not sure how stable it is, I am running two systems at the moment.
after a reboot the system suddenly saw that there wehre volumes on the disks to be reused and activated afterwards it all worked all share where back
only the apps and stuff needs to be backuped and so on
-
1 minute ago, Unregistrado said:
You can create the pool without any problem (not volume!!!!!). Then you will have to repair the installation partition. That is also ok. Did this yesterday and didn’t lose any data.
when i tried to create a pool it stated it needed to format drives
Can it be that the old nas is a 3617xs and new one 3615xs
also the old one runs DSM-6.3.2-25462 new one 7.0.1-42218
i will try to do it later to day again and check the message and snip it to add to here
-
1 minute ago, Unregistrado said:
Put the vmdk on sata0 and 0:0 and your data drive on 1:0. Then it will surely work
i did but chaned it over and rebuild the loader for de 3615xs
No i am facing the issue that the data drives from my old nas
4x3TB and 1 1.5TB are not initialized and i dont want to lose 9TB worth of data including picturesis there away to get then initialized without frmating them
-
2 hours ago, NoFate said:
Thn for all support guys yesterday, 7 is now running on my esxi!!
Mine is no installed but hopefully itwill get past the 10minutes counter and boot trough completly, then i hope i can just put the vm drives of my old dsm 6 vm to the dsm7 vm
and get everything up and running
And it did not it failed somewhere during the 10 minute count down atthe end it gone to something went worng and now its reloading
Any one can help here,
It keeps gooing back to recoverable with the 7.0.1-42218 broadwell package the bromolow package doest even bootVM Config
4vcpus
8GB ram50GB sata drive clean on Sata conroller 0:0 it detects it
the 1GB boot vmdk on sata 1:0 it boot fine from it to the Sata shim version
but the vm will indefinately reload the pat file and timer
-
did your ESXI have a gui, mine does not even get to a gui , if i go to a vmware player it does
I let v2v convert the disk from a clean image vmdk to esx image but still no dice on gui boot -
Just now, NoFate said:
this command? ./rploader.sh satamap now
yeah, i did,
the usb not
USB is not needed if you dont use usb drive if its baremetal then you need to to generate the vid and pid for the usb and put them in the user config as well
-
1 minute ago, NoFate said:
yeah, i changed it, did again this command : ./rploader.sh build bromolow-7.0.1-42218
reboot, but still not finding it
Boot up for DSM can take some time did you also setup the stamaping and serial in de config
-
7 minutes ago, NoFate said:
ok, its booting up, but still cant find it on network, does the mac in esxi needs to be the same as in that json file?
EDIT: gave it the same mac, did a rebuid, but still cant find it
Yes it does, the bootloader searches foor the mac address on boot
-
the file is a convert from the base one from the git repo
i will try to fix the files trough a vmware player on my laptop
-
mine has 4 cores and 4GB but the tc boot fine only commands keep spitting me back to
sudo ./rploader.sh build bromolow-7.0.1-42218 static
./rploader.sh: line 439: jq: command not found
./rploader.sh: line 423: jq: command not found
./rploader.sh: line 423: jq: command not found
./rploader.sh: line 877: jq: command not found
./rploader.sh: line 878: jq: command not found
./rploader.sh: line 879: jq: command not found
./rploader.sh: line 880: jq: command not found
./rploader.sh: line 881: jq: command not found
./rploader.sh: line 882: jq: command not found
./rploader.sh: line 883: jq: command not found
./rploader.sh: line 884: jq: command not found
./rploader.sh: line 885: jq: command not found
./rploader.sh: line 886: jq: command not found
./rploader.sh: line 887: jq: command not found
./rploader.sh: line 888: jq: command not found
./rploader.sh: line 888: jq: command not found
./rploader.sh: line 889: jq: command not found
./rploader.sh: line 889: jq: command not found
./rploader.sh: line 890: jq: command not found
./rploader.sh: line 890: jq: command not found
./rploader.sh: line 891: jq: command not found
Error : Platform not found
./rploader.sh: line 416: jq: command not found
./rploader.sh: line 416: jq: command not found
rploader.shVersion : 0.4.4
----------------------------------------------------------------------------------------
Usage: ./rploader.sh <action> <platform version> <static or compile module> [extension manager arguments]Actions: build, ext, download, clean, update, listmod, serialgen, identifyusb, satamap, mountshare
- build: Build the 💊 RedPill LKM and update the loader image for the specified
platform version and update current loader.- ext: Manage extensions, options go after platform (add/force_add/info/remove/update/cleanup/auto)
example:
rploader.sh ext apollolake-7.0.1-42218 add https://raw.githubusercontent.com/pocopico/rp-ext/master/e1000/rpext-index.json
or for auto detect use
rploader.sh ext apollolake-7.0.1-42218 auto
- download: Download redpill sources only
- clean: Removes all cached files and starts over
- update: Checks github repo for latest version of rploader
- listmods: Tries to figure out required extensions
- serialgen: Generates a serial number and mac address for the following platforms
DS3615xs DS3617xs DS916+ DS918+ DS920+ DVA3219 DVA3221
- identifyusb: Tries to identify your loader usb stick VID:PID and updates the user_config.json file
- satamap: Tries to identify your SataPortMap and DiskIdxMap values and updates the user_config.json file
- backup: Backup and make changes /home/tc changed permanent to your loader disk
- mountshare: Mounts a remote CIFS working directory
Available platform versions:
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Check global_settings.json for settings.
I tried even versions in the global file still same
serialgen gens serial but cant edit the user filelooks like somehow the image has issues with the scripts
-
What is wrong with the VMDK version, i constantly get errors with the rploader commands on jq on multiple lines
-
3 minutes ago, Unregistrado said:
This is the easy way. The hard way is to take the image file export it with Starwind V2V converter to a local ESXi vmdk file. You get two files upload them to ESXI and then create your virtual machine.
Easy way is faster
-
1
-
-
You have just putthe vmdk on your ESXI server that does not work
You will need to convert it to the proper format for ESXI
i had the same thing
Setup SSH on your host and go to the datastore on your host where the vmdk is stored
use cd /vmfs/volumes/datastorename/ replace datastorename with teh actual name of the datastore
and run this vmkfstools -i HostedVirtualDisk ESXVirtualDisk replace hostedvirtual disk with /vmfs/volumes/datastorename/path to vmdk and replace ESXIVirtualdisk with the name of the new vmdk file with teh same path in front of it.-
1
-
-
I got the files running but now the build wont run
./rploader.sh build bromolow-7.0.1-42218 static
tc@box:~$ ./rploader.sh build bromolow-7.0.1-42218 static
./rploader.sh: line 439: jq: command not found
./rploader.sh: line 423: jq: command not found
./rploader.sh: line 423: jq: command not found
./rploader.sh: line 877: jq: command not found
./rploader.sh: line 878: jq: command not found
./rploader.sh: line 879: jq: command not found
./rploader.sh: line 880: jq: command not found
./rploader.sh: line 881: jq: command not found
./rploader.sh: line 882: jq: command not found
./rploader.sh: line 883: jq: command not found
./rploader.sh: line 884: jq: command not found
./rploader.sh: line 885: jq: command not found
./rploader.sh: line 886: jq: command not found
./rploader.sh: line 887: jq: command not found
./rploader.sh: line 888: jq: command not found
./rploader.sh: line 888: jq: command not found
./rploader.sh: line 889: jq: command not found
./rploader.sh: line 889: jq: command not found
./rploader.sh: line 890: jq: command not found
./rploader.sh: line 890: jq: command not found
./rploader.sh: line 891: jq: command not found
Error : Platform not found
./rploader.sh: line 416: jq: command not found
./rploader.sh: line 416: jq: command not found
rploader.sh -
I tried to copy over the files to the ESXI vm with the tiny core but every time i try to run the rploader.sh it keeps saying its not found but when i ls it shows
i used win scp to transfer over the rploader.sh and config files even te vmdk file also tried to run chmd +x on the rpoader.sh
if i for Ex do sudo ./rploader.sh serialgen DS3615xs now or sudo ./rploader.sh update now it constantly spit back unable to execpute no such file or directory
-
I dont have this issue, i have a paid wildcard systemwide cert, but have seen simular behaveior on linux web servers
Try to take out the systemwide lets encrypt from controlpanel --> security --> certificatesThen download station should work normally again from its setup custom link
Sabnzbd is another case, one of the reasons i stoped using it was that its picky at best with https and certificates.
Try to install nzbget it does exactly the same things as sabnzbd but is les picky on certificates and ssl settings -
check my signature,
There is my servers hardware configAlso the full vm config is stated
It uses the loader for DS3617xs DSM version DSM 6.2.3-25426Serives running Sonarr,Radarr nzbget and a Spotweb instance with a maria DBv10 database and a docker for guacamole.
-
for the last 2 days my Xpenology vm sends out an email about unporper reboot/shutdown , when checking the events logs in esxi it states the following
The CPU has been disabled by the guest operating system. Power off or reset the virtual machine.
Vm based on DS3617XS
HW Config of VM
CPU
8 vCPUs
Memory
16 GB
Hard disk 1
250 GB
Hard disk 2
160 GB
Hard disk 3
1.6 TB
Hard disk 4
50 MB
Hard disk 5
2.73 TB Passtrough 3TB red drver
Hard disk 6
2.73 TB Passtrough 3TB red drver
Hard disk 7
2.73 TB Passtrough 3TB red drver
Hard disk 8
2.73 TB Passtrough 3TB red drver
USB controller
USB 3.1
PCI Devices a 4port usb 3.0 controller with an usb 12tb drive as data backup drive.
This did not happen before
I cant pinpoint what does this.
-
the 3tb disk where passtrough
the boot drive is a 50mb img file stored on on of the 2 TB drives
de ssd boot drive has no vms on its data store
-
Is it posible to run xpenology bare metal on the following system
Motherboard : Asrock X79 Extreme 11
- 2 x SATA3 6.0 Gb/s connectors by Intel® X79, support RAID (RAID 0, RAID 1, RAID 5, RAID 10 and Intel® Rapid Storage 3.0), NCQ, AHCI and Hot Plug functions
- 8 x SAS2/SATA3 6.0 Gb/s connectors by LSI SAS2308 PCIe 3.0 controller, support RAID (RAID 0, RAID 1, RAID 1E and RAID 10), NCQ and Hot Plug functions
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Broadcom BCM57781
- Supports Wake-On-LAN
- Supports Energy Efficient Ethernet 802.3az
- Supports Dual LAN with Teaming function
- Supports PXE
Drive configuration
1SSD NVME will be used as Cache1 ssd as drive for Docker/VM MAnager
2 2TB drives as main storage for packages
4 3TB drives as Bulk storage (backuped to a usb 3.0 attached 12TB drive)
I am now running it trough a esxi hypervisor but i rum in to some bottlenecks, and want to use the VM Manager and docker stuff with the virtualization support
There are some parts in the box XPEnology does not like to support the Quadro M2000 gpu ( would be nice if it could work some day)
Main uses are storage , Webserver and media server With HW transcoding
ESXI host now has the following vms
XPEnology 6.2
Windows 10 with Plex media server installed
Ubuntu 20.04 desktop (unifi controller)
Unbuntu 20.04 desktop (Adguard)Open VPN server
Webremote server (Unbutu 20.04 with couldron and guacamole)and a play around vm for Windows 11 and other new windows osses like server previews
I main intend is to install xpenology on it and run die Unifi controller and adguard and a reverse proxy inside a docker or VM in VM Manager
Is it posible to passtrough a GPU eventough dsm doesnt use it to a VM of Docker so plex can run with HW transcoding on
Are those things doable or do i need to go the ESXI route -
On the boot drive (usb Flash drive) u use to boot je bare metal system there is a floder called Grub in that folder you will find an grub.txt file that is the boot config synoboot usses to set things like usb flash pid and vid and nic macs
please share that so we can see if the config file is the culprit of you mac issues
-
synoboot.vmdk
Hello, i have an issue i cant enable SSH on my syno box and due to an internal network change my bond ahs the wrong DNS and now my XpeNology box is completely un reachable.Does anyone has any option to reset it without my data on 4 passtrough 3TB drive is gone.
-
are you running baremetal or trough and hypervisor like ESXI
Also please post pictures of config and DSM and EFI settings
-
Mac addresses should not change the are hard coded to the nic if the nic in dsm some how get a new mac then we need te check configs and bios/efi of the system
DSM 5.x/6.x/7.x CPU name & cores infomation Change tool
in Software Modding
Posted
Mine doesnt show the 12 treads my cpu has
DSM CPU Information Change Tool ver. 4.2.1-r01 - made by FOXBI
Your version of DSM is DSM 7.1.1-42962 Update 6
The CPU information to be applied is as follows.
Intel Xeon X5660 [6 Cores (1 CPU/6 Cores | 6 Threads)-] continue...
the x5660 is a 6core 12 tread cpu ht is on
sudo dmidecode -t processor | grep HTT
Password:
HTT (Multi-threading)
grep -o '^flags\b.*: .*\bht\b' /proc/cpuinfo | tail -1
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht