so my psu blew on my gen8 microserver a couple of weeks ago. it took out the first two sata ports on the onboard controller as well (thanksfully not the backplane too!)
ive since bought a hp p222 controller and i'm trying to get it working. i have dsm6.2 on there currently, so need to upgrade to DSM7 to get the new card working
testing ARPL on a single spare drive to see how i get on, i chose DS3622xs+
compile the bootloader and reboot, im getting "no disks found"
i've disabled the onboard controller and set the p222 to the first available controller in bios.
checking dmesg on the arpl bootup, i see this:
[ 4.939842] HP HPSA Driver (v 3.4.20-200)
[ 4.939854] hpsa 0000:07:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 4.940768] hpsa 0000:07:00.0: Logical aborts not supported
[ 4.940771] hpsa 0000:07:00.0: HP SSD Smart Path aborts not supported
[ 4.956915] tg3 0000:03:00.0 eth0: Tigon3 [partno(N/A) rev 5720000] (PCI Express) MAC address b0:5a:da:87:7f:24
[ 4.956921] tg3 0000:03:00.0 eth0: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 4.956923] tg3 0000:03:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[ 4.956924] tg3 0000:03:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
[ 4.967838] tg3 0000:03:00.1 eth1: Tigon3 [partno(N/A) rev 5720000] (PCI Express) MAC address b0:5a:da:87:7f:25
[ 4.967842] tg3 0000:03:00.1 eth1: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 4.967843] tg3 0000:03:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[ 4.967845] tg3 0000:03:00.1 eth1: dma_rwctrl[00000001] dma_mask[64-bit]
[ 4.977599] scsi host1: hpsa
[ 4.977755] hpsa can't handle SMP requests
[ 4.984042] hpsa 0000:07:00.0: scsi 1:0:0:0: added RAID HP P222 controller SSDSmartPathCap- En- Exp=1
[ 4.984046] hpsa 0000:07:00.0: scsi 1:0:1:0: added Direct-Access ATA WDC WD100EZAZ-11 PHYS DRV SSDSmartPathCap- En- Exp=1
[ 4.984049] hpsa 0000:07:00.0: scsi 1:0:2:0: masked Enclosure PMCSIERA SRCv8x6G enclosure SSDSmartPathCap- En- Exp=0
[ 4.984085] hpsa can't handle SMP requests
[ 4.984172] scsi 1:0:0:0: RAID HP P222 8.32 PQ: 0 ANSI: 5
[ 4.984307] scsi 1:0:0:0: Attached scsi generic sg1 type 12
[ 4.984362] hpsa can't handle SMP requests
[ 4.984757] scsi 1:0:1:0: Direct-Access ATA WDC WD100EZAZ-11 0A83 PQ: 0 ANSI: 6
[ 4.985938] sd 1:0:1:0: Attached scsi generic sg2 type 0
[ 4.986829] sd 1:0:1:0: [sdb] 19532873728 512-byte logical blocks: (10.0 TB/9.10 TiB)
[ 4.986834] sd 1:0:1:0: [sdb] 4096-byte physical blocks
[ 4.987018] sd 1:0:1:0: [sdb] Write Protect is off
[ 4.987021] sd 1:0:1:0: [sdb] Mode Sense: 46 00 10 08
[ 4.987378] sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 5.077006] sdb: sdb1 sdb2 sdb5 sdb6
[ 5.078518] sd 1:0:1:0: [sdb] Attached SCSI disk
[ 5.355690] udevadm (168) used greatest stack depth: 14056 bytes left
[ 5.366430] ip (198) used greatest stack depth: 13832 bytes left
[ 5.378070] NET: Registered PF_INET6 protocol family
[ 5.378514] Segment Routing with IPv6
[ 5.378519] In-situ OAM (IOAM) with IPv6
[ 5.394258] 8021q: 802.1Q VLAN Support v1.8
[ 6.511541] random: crng init done
[ 6.511543] random: 7 urandom warning(s) missed due to ratelimiting
[ 7.601324] blkid (256) used greatest stack depth: 13680 bytes left
[ 8.157687] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null). Quota mode: none.
[ 8.222490] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[ 8.525665] ip (352) used greatest stack depth: 13656 bytes left
[ 9.004682] tg3 0000:03:00.0 eth0: Link is up at 1000 Mbps, full duplex
[ 9.004687] tg3 0000:03:00.0 eth0: Flow control is on for TX and on for RX
[ 9.004688] tg3 0000:03:00.0 eth0: EEE is disabled
[ 9.004709] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.114327] tg3 0000:03:00.1 eth1: Link is up at 1000 Mbps, full duplex
[ 9.114332] tg3 0000:03:00.1 eth1: Flow control is on for TX and on for RX
[ 9.114333] tg3 0000:03:00.1 eth1: EEE is disabled
[ 9.114341] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 11.513738] udevd (158) used greatest stack depth: 13176 bytes left
i cant work out what i need to set sataportmap to so i can see the drives on the p222. can someone explain how i translate above output?
once i've got this working, im gonna try upgrading my dsm6 setup and putting the 4 SHR drives back in. any tips on the best process to follow to do this so i dont break the array and/or lose my data? (my theory is use arpl to upgrade to 7.0.1 and then to a later version?)
Question
wanye
so my psu blew on my gen8 microserver a couple of weeks ago. it took out the first two sata ports on the onboard controller as well (thanksfully not the backplane too!)
ive since bought a hp p222 controller and i'm trying to get it working. i have dsm6.2 on there currently, so need to upgrade to DSM7 to get the new card working
testing ARPL on a single spare drive to see how i get on, i chose DS3622xs+
compile the bootloader and reboot, im getting "no disks found"
i've disabled the onboard controller and set the p222 to the first available controller in bios.
checking dmesg on the arpl bootup, i see this:
i cant work out what i need to set sataportmap to so i can see the drives on the p222. can someone explain how i translate above output?
once i've got this working, im gonna try upgrading my dsm6 setup and putting the 4 SHR drives back in. any tips on the best process to follow to do this so i dont break the array and/or lose my data? (my theory is use arpl to upgrade to 7.0.1 and then to a later version?)
Edited by wanyeLink to comment
Share on other sites
2 answers to this question
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.