arunmcops
-
Posts
15 -
Joined
-
Last visited
Posts posted by arunmcops
-
-
Please post your output of ssh commands used for installation.
-
System Config:
CPU- Intel Core i5 3570
MB- Intel H61
HDD/SSD- As below
SATA Controllers- 1. Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 05) (4 SATA3 Ports)
2. Marvell Technology Group Ltd. Device 9215 (rev 11) (4 SATA3 Ports)
Issue:
Found "00:1f.2 Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 05)" Detected 6 ports/3 drives. Bad ports: 3 4. Override # of ports or ENTER to accept <6> Found "03:00.0 Marvell Technology Group Ltd. Device 9215 (rev 11)" Detected 4 ports/0 drives. Override # of ports or ENTER to accept <4> Computed settings: SataPortMap=64 DiskIdxMap=0006 WARNING: Bad ports are mapped. The DSM installation will fail!
Port 3, 4 aka bad ports don't even exist on board. DSM working fine.
Drive 1/4 are on Marvell Controller and Drive 11/12 are on Intel onboard SATA Controller.
Edit: Tried putting all 4 drives in Intel Controller and only 3 are detected.So it seems one physical sata port is mapped as Bad port although same is working fine in other OSes including TCRP.
-
Thanks for your continuous support. Today I went through a lot of your posts, and learnt a lot.
A heartfelt thanks from community of fellows who are new to Xpenology.
- 1
-
11 hours ago, Peter Suh said:
pid/vid should be replaced with that of your usb stick. It should not be used as I wrote it. The only thing I want to emphasize is this. SataPortMap": "",
"DiskIdxMap": "" And that black console has nothing more to do. Another need to type find.synology.com in your PC's web browser and monitor the IP assignment.😁 Honest mistake. Will do that today evening. I too was confused as to why json file is showing different VID/PID as well as MAC ID than actual hardware.
- 1
-
13 hours ago, Peter Suh said:
Like This.
tc@box:~$ cat user_config.json
{
"extra_cmdline": {
"pid": "0xa4a5",
"vid": "0x0525",
"sn": "1230LWN009033",
"mac1": "0011322A46E7",
"SataPortMap": "",
"DiskIdxMap": ""
},
"synoinfo": {"internalportcfg" : "0xffff",
"maxdisks" : "16",
"support_bde_internal_10g" : "no",
"support_disk_compatibility" : "no",
"support_memory_compatibility" : "no"
},
"ramdisk_copy": {
}}
Done it. No result. Same status.
-
Tried again with DS3622xs+. Sata controller and port mapping went ok but same issue again ..
It looks that you will need the following modules :
Found SATA Controller : pciid 1022d00007801 Required Extension :
No matching extensionAny extention available or any way to add it ?
-
9 minutes ago, Peter Suh said:
Instead, you just need to see if the dtbpatch or redpill-dtb-static ext driver is being installed normally.
How to do this ? process ?
-
Tried to install with DS1621+ but encountered this error :
It looks that you will need the following modules :
Found SATA Controller : pciid 1022d00007801 Required Extension :
No matching extensionAs per lspci, the sata controller is as below:
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 40)
After creation of bootable USB, stuck at this
-
Hardware:
C2Q Q6600
Intel MB
2x 2TB HDDs
2x2 GB DDR2
Setup was working fine for a week, then I upgraded RAM to 4x2 GB DDR2.
Then system refused to boot.
Tried 3 different pen drives to reinstall, but it stucks while booting TCRP at "Loading Kernel" then black screen and no Tiny Core GUI. System also not available on network.
Tried same pen drive on my laptop and it works fine.
Also removed both HDDs still same status.
Any help would be highly appreciated.
-
Tried thrice with 3 different USB Sticks. Always verified VID / PID of each usb stick, still same error.
-
Hi,
I have AMD 4700S system.
8 Core Ryzen, 16 GB RAM, 2 SATA Ports.
2x 2 TB WD HDDs.
Which system would be workable ?
3622xs+ or any other ?
-
System Info:
Intel G41 Board
Intel Q9400 CPU
8GB RAM
2X 2 TB WD HDDs
I installed DS3622xs+ . It went fine and installed correctly. Made a Plex server, uploaded the media. It was working good.
Then I had to shift the house. During shifting, USB Pen Drive got lost.
Now I again tried to install same system, but I am getting countinuous error about pat file being corrupt.
Tried 3 different pen drives. No luck.
System is headless.
Do I need to connect monitor and select SATA during boot ?
Do I need to format HDDs ?
Please help me out.
-
On 6/1/2022 at 6:27 PM, Peter Suh said:
Try it with the DS3622xs+.
In the past, my first Xpenology had similar specifications to yours.
At the time, I used DS3615xs,
A better DS3622xs+ is available now.Thanks. Used the same . Working perfectly. I have one more query.
DSM shows 12 HDD support. My board has 4 sata ports.
Can I add PCI Express to SATA addon board to increase the sata ports ?
-
Which Loader to choose for the following hardware:
Motherboard: Intel DG33FB
CPU: Intel Core 2 Quad 6600
Memory: 4 GB. Planned upgrade to 8 GB.Thank you so much for your kind help
Transcoding WITHOUT a valid serial number
in Software Modding
Posted
Does it work with DSM 7.1.1-42962-1 ?