[DSM 7.1-42661 Update 4]

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 4

- Loader version and model: Tinycore-Redpill 0.8.0.3 - DS3622xs+ (tinycore-redpill-uefi.v0.8.0.0.img.gz)

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - MACHINIST X99 Motherboard LGA 2011-3/ Intel Xeon E5 2673 V3/ 16GB (2*8GB) DDR4 (non ECC)  2666MHz RAM

- Additional comments:
1:    From DSM Control Panel> Update & Restore>Manual DSM Update and wait for reboot
2:    

tc@box:~$ ./rploader.sh update

3:    

tc@box:~$ sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661

4:  

 tc@box:~$ exitcheck.sh reboot

[DSM 7.1-42661 Update 2]

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2

- Loader version and model: Tinycore-Redpill 0.8.0.3 - DS3622xs+ (tinycore-redpill-uefi.v0.8.0.0.img.gz)

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - MACHINIST X99 Motherboard LGA 2011-3/ Intel Xeon E5 2673 V3/ 16GB (2*8GB) DDR4 (non ECC)  2666MHz RAM

- Additional comments: From DSM Control Panel> Update & Restore>Manual DSM Update and wait for reboot in TCRP. Then run:

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot

[User Reported Compatibility Thread for DSM 6.2]

On 8/26/2021 at 5:24 AM, smoothmove said:

Success - without any install issues.  Installed first time with reboot

 

Loader version and type (918+/3615xs/3617xs):   DS3617XS. Jun 1.03b

DSM version in use (including critical update):  DSM 6.2.3-24526 Update 3

Using custom modules/ramdisk? If yes which one?:  Standard install in Legacy

Hardware details (try being specific without giving long and useless technical details - model version, motherboard and NIC used should suffice):

 

Machinist X99-K9 (Same as Machinist X99Z V102)

E5-2699 V3 (HT disabled and restricted to 16 cores) 

16gb - 4x4gb DDR4 2400

Intel X540-T2 10Gbe network (on board Realtek also works)

PCIe 1x Nvidia 710 video

Hi, i have exactly same MACHINIST X99  using onboard NIC with loader Jun 1.03b. unable to connect to network. Is there any modification in BIOS  or Bootloader? appreciate  your support.

[RedPill - the new loader for 6.2.4 - Discussion]

18 minutes ago, WiteWulf said:

Okay, I've managed to get my HP Gen8 Microserver to 6.2.4 on baremetal 🥳

 

I encountered two problems while running the migration:
- the first reboot after reinstalling the 25556 pat it tried to boot off the internal hdd, rather than the USB stick. I seem to recall this being a common problem with firmware updates in the past anyway, and likely isn't unique to this release/boot method. A reboot fixed this and it booted off the USB stick properly and completed the install

- after install the NIC had changed to DHCP, rather than static, for some reason. This was easily changed in the Control Panel in DSM

 

Thanks for all the hard work and help getting this far!

 

Now, unfortunately, it's rebooted itself twice since the upgrade completed (in the last ten minutes or so). I'll look into this further and see if I can figure out what the problem is, 

Great!,

it would be helpful, create step by step guide from loader to complete migration.

[DSM 6.2.3-25426]

 Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: DS3615xs_V1.03b_MBR_Zandstraal

- Using custom extra.lzma: NO

- Installation type: Baremetal HP DC7600 convertible tower

 

[Transfer drives from Synology to XPEnology]

Hi Cralis,

have you done your migration successfully? Please share your experience...