IG-88

How to build and inject missing drivers in jun loader 1.02a

Recommended Posts

Ok just confirmed via mac address lookup that is it intel 82573V gigabyte lan. Bios also says enable/disable intel lan.

 

So why would this not load up in juns 1.02b LZMA version? I did not try 1.02a, Also Keep in mind I tried to replace the standard LZMA (because 1.02b changes the way the partitions are setup from 1.01). I tried to change the LZMA in 1.02b in the second partition on the USB by using AccessData FTK Imager. I could not use OSFMount because it could not lock the drive & thus save changes. I tried with admin rights also same results so I switched to using AccessData FTK Imager which loads all paritions at once and allows you to save each separately. Perhaps the way this was done could have corrupted the partition or something else but that seems odd since it loads the img fine & I tried it twice. I am on a windows 8 machine doing this but have access to OSX and a ubuntu mini install. The ubuntu I tend not to use because its so new to me.

 

Here are a few questions:

 

1. Do you have any tricks to using OSFmount?

 

2. Is 1.02a better to use then 1.02b?

 

3. Is there another driver LZMA I can try with 1.02b? I could not find any besides the HP 1 mentioned. When I tried to use the 1.01 version it of course did not work since its different kernel. I could not find any others except the one for the HP server n36l-n54l.zip but that does not include VIA_PATA but did include my Intel LAN. Its the only LZMA I am aware of outside the original included with juns loader which wont load my lan.

 

I hope this is clear IG-88, in my previous posts where I said realtek I meant INTEL.. THANKS FOR THE HELP AGAIN. I think I just need a new LZMA with VIA_PATA and the INTEL LAN. THE n36l-n54l.zip could be the base for this since it has the correct lan driver. I'm willing to try more testing of this again with your suggestions.

Edited by madhits45

Share this post


Link to post
Share on other sites
18 hours ago, madhits45 said:

1. Do you have any tricks to using OSFmount?

 

2. Is 1.02a better to use then 1.02b?

 

when loading the img file make sure to uncheck the read only!

the 1.02b image is definitely better and has more drivers included. you can't use older LZMA with this version

OSFMount.png

Share this post


Link to post
Share on other sites
30 minutes ago, opty said:

when loading the img file make sure to uncheck the read only!

the 1.02b image is definitely better and has more drivers included. you can't use older LZMA with this version

OSFMount.png

Ya I've been doing that its mentioned in Polanskiman guide.. The issue seems to be once the drive is mounted windows won't let anything lock the drive. So I am forced to abandon the changes. AccessData FTK Imager does not have this problem, but I was worried cuz using a different app sometimes has issues of its own. Thanks though.. 

Share this post


Link to post
Share on other sites

you can also do it on OS X to edit the grub file using disk utility. open the img first and than mount it doing it this way you won't be able to do anything with LZMA but you can edit grub.

Share this post


Link to post
Share on other sites
3 minutes ago, opty said:

you can also do it on OS X to edit the grub file using disk utility. open the img first and than mount it doing it this way you won't be able to do anything with LZMA but you can edit grub.

 

So it will mount the image and I can change things and re-save? Sweet ill give that a try..

Share this post


Link to post
Share on other sites

one other thing you should consider is using the right text editor, i myself use sublime with no issue.

Share this post


Link to post
Share on other sites
On 1.8.2017 at 8:59 PM, madhits45 said:

Ok just confirmed via mac address lookup that is it intel 82573V gigabyte lan. Bios also says enable/disable intel lan.

 

So why would this not load up in juns 1.02b LZMA version? I did not try 1.02a, Also Keep in mind I tried to replace the standard LZMA (because 1.02b changes the way the partitions are setup from 1.01). I tried to change the LZMA in 1.02b in the second partition on the USB by using AccessData FTK Imager. I could not use OSFMount because it could not lock the drive & thus save changes. I tried with admin rights also same results so I switched to using AccessData FTK Imager which loads all paritions at once and allows you to save each separately. Perhaps the way this was done could have corrupted the partition or something else but that seems odd since it loads the img fine & I tried it twice. I am on a windows 8 machine doing this but have access to OSX and a ubuntu mini install. The ubuntu I tend not to use because its so new to me.

 

Here are a few questions:

 

1. Do you have any tricks to using OSFmount?

osfmount asks for elevated rights by itself to run with administrator rights

just open the image, selct 2nd partition, ok, unckeck read-only, ok and there is a additionl drive letter with the content /extra.lzma)

afair the same a writen in polanskimans howto

 

Quote

2. Is 1.02a better to use then 1.02b?

 

using 1.02b is better, it fixes a problem that after a major update (6.1 -> 6.1.1) with a complete pat file 1.02a did not load the drivers from the extra.lzma so the system was not working anymore

no need for 1.02a and 1.02b does only contain 2 additional driver compared with 1.02a the r8168 (realtek gigabit driver from realtek website, r8169 is the one delivered with the linux kernel) and mpt3sas.ko (for newer lsi 12Gbit controller?)

 

Quote

3. Is there another driver LZMA I can try with 1.02b? I could not find any besides the HP 1 mentioned. When I tried to use the 1.01 version it of course did not work since i

 

as the one for the hp systems is working for you i could repackage the extra.lma from this and put the pata_via driver in

you would just have to exchange the extra.lzma before creating the boot stick and of course using the old/fist 6.1 pat file (15047)

 

Quote

 

ts different kernel. I could not find any others except the one for the HP server n36l-n54l.zip but that does not include VIA_PATA but did include my Intel LAN. Its the only LZMA I am aware of outside the original included with juns loader which wont load my lan.

 

I hope this is clear IG-88, in my previous posts where I said realtek I meant INTEL.. THANKS FOR THE HELP AGAIN. I think I just need a new LZMA with VIA_PATA and the INTEL LAN. THE n36l-n54l.zip could be the base for this since it has the correct lan driver. I'm willing to try more testing of this again with your suggestions.

 

i still want to know what mainboard it is, it's not so hard to grab a flashlight and read whats writen on the board

 

Edited by IG-88

Share this post


Link to post
Share on other sites
30 minutes ago, IG-88 said:

osfmount asks for elevated rights by itself to run with administrator rights

just open the image, selct 2nd partition, ok, unckeck read-only, ok and there is a additionl drive letter with the content /extra.lzma)

afair the same a writen in polanskimans howto

OK yeah I did that all correctly it just won't lock the drive and thus won't let me save the img. I think AccessData FTK Imager is working so ill stick with it or switch to disk utility on the mac.

Quote

 

 

using 1.02b is better, it fixes a problem that after a major update (6.1 -> 6.1.1) with a complete pat file 1.02a did not load the drivers from the extra.lzma so the system was not working anymore

no need for 1.02a and 1.02b does only contain 1 additional driver compared with 1.02a the r8168 (realtek gigabit driver from realtek website, r8169 is the one delivered with the linux kernel)

Ok Ill stick with 1.02b

Quote

 

 

as the one for the hp systems is working for you i could repackage the extra.lma from this and put the pata_via driver in

you would just have to exchange the extra.lzma before creating the boot stick and of course using the old/fist 6.1 pat file (15047)

 

I've tried to repack that LZMA myself but could not find the VIA_PATA.ko recompiled for the kernel in 6.1, so i'm stuck there. Do you have a link to an updated driver pack for 1.02b that has the VIA_PATA.ko?

Quote

 

 

i still want to know what mainboard it is, it's not so hard to grab a flashlight and read whats writen on the board

Sure here is the link to my main board specs:

https://msi.com/Motherboard/945p_platinum.html#hero-overview

 

Its not a super popular board even at the time that I bought it. I wish I had gone with asus but its still working and I figured out a way to dual boot Xpenology and kodi. This xpenology box is my backup to my main 6TB NAS.. so its not turned on a lot. I run it via schedule.

 

Also IG-88.. When I was running DSM 6.0 I could not get proper shutdown/restart as soon as I get the driver for VIA working that will be my next thing to overcome, any ideas about that? Or could it be that DSM 6.1 will fix this? I had shutdown working in 5.2 but it did take some tweaking if I recall.

Quote

 

 

Edited by madhits45

Share this post


Link to post
Share on other sites
4 hours ago, madhits45 said:

Will do, hope it loads.. thx much!

UPDATE: It did not load the VIA driver again. Same problem as 6.0.2? Any ideas?

 

I confirmed that AccessData FTK Imager saved the changes to the image. I used OSFmount to see that the extra.lzma and the grub.cfg were written correctly. Its something with the driver, it simply wont load. I get into DSM via find synology and it says no hard drives. The network driver is loading up though, so that's something.

Share this post


Link to post
Share on other sites
On 3.8.2017 at 4:18 AM, madhits45 said:

UPDATE: It did not load the VIA driver again. Same problem as 6.0.2? Any ideas?

 

I confirmed that AccessData FTK Imager saved the changes to the image. I used OSFmount to see that the extra.lzma and the grub.cfg were written correctly. Its something with the driver, it simply wont load. I get into DSM via find synology and it says no hard drives. The network driver is loading up though, so that's something.

as the network is running, can you have a look whats in the log why it does not work?

Share this post


Link to post
Share on other sites
4 hours ago, IG-88 said:

as the network is running, can you have a look whats in the log why it does not work?

I know this is a dumb question, but where is the log? On the USB or inside DSM?

Share this post


Link to post
Share on other sites
5 minutes ago, madhits45 said:

I know this is a dumb question, but where is the log? On the USB or inside DSM?

 

the log is in dsm (its the same as with every other linux, like debian or ubuntu) use putty, ssh session (maybe ssh has to be activates in dsm web gui, control panel, terminal & snmp) , in ssh session login with the admin account, "dmesg | grep -i via"

instead auf via you can serch for other words like usb, sda or eth0, depending what you are looking for

"dmesg | more" will list all and with space you can go page wise, strg-c if you want out before you reach the end

 

https://www.tecmint.com/dmesg-commands/

 

there should be something about pata_via as it's in the rc.modules were the "drivers" to load at boot are in

 

Share this post


Link to post
Share on other sites
31 minutes ago, IG-88 said:

 

the log is in dsm (its the same as with every other linux, like debian or ubuntu) use putty, ssh session (maybe ssh has to be activates in dsm web gui, control panel, terminal & snmp) , in ssh session login with the admin account, "dmesg | grep -i via"

instead auf via you can serch for other words like usb, sda or eth0, depending what you are looking for

"dmesg | more" will list all and with space you can go page wise, strg-c if you want out before you reach the end

 

https://www.tecmint.com/dmesg-commands/

 

there should be something about pata_via as it's in the rc.modules were the "drivers" to load at boot are in

 

Sweet that makes sense, just like osx.

Share this post


Link to post
Share on other sites

Just had an idea, could this be a driver ID issue? IE my chipset is not in the driver index and thus it wont ID it to load, ive seen that before in windows. Perhaps its happening here, thoughts?

 

Ill report back after I get into SSH of this box, trying to install DSM 6.1 now.

Share this post


Link to post
Share on other sites

IG-88.. Here is the output. unknown symbol, could it be that it did not ID the hardware correctly?

 

dmesg | grep -i via
[   20.680059] pata_via: Unknown symbol syno_libata_index_get (err 0)
[   46.669469] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[   46.669475] via_rhine: Broken BIOS detected, avoid_D3 enabled

 

DMESG MORE  

 dmesg | more
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.102 (root@build1) (gcc version 4.9.3 20150311
(prerelease) (crosstool-NG 1.20.0) ) #15047 SMP Thu Feb 23 02:24:19 CST 2017
[    0.000000] Command line: BOOT_IMAGE=/zImage syno_hdd_powerup_seq=0 HddHotplu
g=0 syno_hw_version=DS3615xs vender_format_version=2 console=ttyS0,115200n8 with
efi elevator=elevator quiet syno_port_thaw=1 root=/dev/md0 sn=1430LWN981629 mac1
=0013D3390f32 netif_num=1 vid=0x14CD pid=0x125C
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bfedf7ff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bfedf800-0x00000000bfedffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000bfee0000-0x00000000bfee2fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bfee3000-0x00000000bfeeffff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000bfef0000-0x00000000bfefffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.2 present.
[    0.000000] DMI:    /MS-7176, BIOS 6.00 PG 01/11/2006
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0xbfedf max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CDFFF write-protect
[    0.000000]   CE000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-through
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0BFF00000 mask FFFF00000 write-through
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] found SMP MP-table at [mem 0x000f5160-0x000f516f] mapped at [ffff
8800000f5160]
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01abe000, 0x01abefff] PGTABLE
[    0.000000] BRK [0x01abf000, 0x01abffff] PGTABLE
[    0.000000] BRK [0x01ac0000, 0x01ac0fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xbfc00000-0xbfdfffff]
[    0.000000]  [mem 0xbfc00000-0xbfdfffff] page 2M
[    0.000000] BRK [0x01ac1000, 0x01ac1fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xbc000000-0xbfbfffff]
[    0.000000]  [mem 0xbc000000-0xbfbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x80000000-0xbbffffff]
[    0.000000]  [mem 0x80000000-0xbbffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x7fffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x7fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0xbfe00000-0xbfedefff]
[    0.000000]  [mem 0xbfe00000-0xbfedefff] page 4k
[    0.000000] BRK [0x01ac2000, 0x01ac2fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x36f32000-0x37790fff]
[    0.000000] ACPI: RSDP 0x00000000000F9380 00014 (v00 IntelR)
[    0.000000] ACPI: RSDT 0x00000000BFEE3040 00030 (v01 IntelR AWRDACPI 42302E31
 AWRD 00000000)
[    0.000000] ACPI: FACP 0x00000000BFEE30C0 00074 (v01 IntelR AWRDACPI 42302E31
 AWRD 00000000)
[    0.000000] ACPI: DSDT 0x00000000BFEE3180 04852 (v01 INTELR AWRDACPI 00001000
 MSFT 0100000E)
[    0.000000] ACPI: FACS 0x00000000BFEE0000 00040
[    0.000000] ACPI: MCFG 0x00000000BFEE7B40 0003C (v01 IntelR AWRDACPI 42302E31
 AWRD 00000000)
[    0.000000] ACPI: APIC 0x00000000BFEE7A40 00084 (v01 IntelR AWRDACPI 42302E31
 AWRD 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000]  [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800bc400000-fff
f8800bedfffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xbfedefff]
[    0.000000] On node 0 totalpages: 786045
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10693 pages used for memmap
[    0.000000]   DMA32 zone: 782047 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] e820: [mem 0xbff00000-0xdfffffff] available for PCI devices
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_id
s:1
[    0.000000] PERCPU: Embedded 24 pages/cpu @ffff8800bfa00000 s69312 r8192 d208
00 u524288
[    0.000000] pcpu-alloc: s69312 r8192 d20800 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 775275
[    0.000000] Kernel command line: BOOT_IMAGE=/zImage syno_hdd_powerup_seq=0 Hd
dHotplug=0 syno_hw_version=DS3615xs vender_format_version=2 console=ttyS0,115200
n8 withefi elevator=elevator quiet syno_port_thaw=1 root=/dev/md0 sn=1430LWN9816
29 mac1=0013D3390f32 netif_num=1 vid=0x14CD pid=0x125C
[    0.000000] Power on seq num: 0
[    0.000000] Synology Hardware Version: DS3615xs-j
[    0.000000] Vender format version: 2
[    0.000000] Serial Number: 1430LWN981629
[    0.000000] Mac1: 0013D3390f32
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes
)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Memory: 3074808k/3144572k available (4796k kernel code, 392k abse
nt, 69372k reserved, 3809k data, 760k init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] NR_IRQS:4352 nr_irqs:712 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] allocated 12582912 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memor
y cgroups
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 3014.928 MHz processor
[    0.002004] Calibrating delay loop (skipped), value calculated using timer fr
equency.. 6029.85 BogoMIPS (lpj=3014928)
[    0.002010] pid_max: default: 32768 minimum: 301
[    0.002066] Security Framework initialized
[    0.002079] AppArmor: AppArmor initialized
[    0.002097] Mount-cache hash table entries: 256
[    0.002369] Initializing cgroup subsys memory
[    0.002390] Initializing cgroup subsys devices
[    0.002393] Initializing cgroup subsys freezer
[    0.002396] Initializing cgroup subsys blkio
[    0.002443] CPU: Physical Processor ID: 0
[    0.002446] CPU: Processor Core ID: 0
[    0.002449] mce: CPU supports 4 MCE banks
[    0.002462] CPU0: Thermal monitoring enabled (TM1)
[    0.002472] Last level iTLB entries: 4KB 128, 2MB 128, 4MB 128
               Last level dTLB entries: 4KB 64, 2MB 0, 4MB 64
               tlb_flushall_shift: 6
[    0.002529] Freeing SMP alternatives: 24k freed
[    0.002545] ACPI: Core revision 20130328
[    0.004988] ACPI: All ACPI Tables successfully acquired
[    0.007277] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.017291] smpboot: CPU0: Intel(R) Pentium(R) D CPU 3.00GHz (fam: 0f, model:
 06, stepping: 02)
[    0.018000] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[    0.018000] ... version:                0
[    0.018000] ... bit width:              40
[    0.018000] ... generic registers:      18
[    0.018000] ... value mask:             000000ffffffffff
[    0.018000] ... max period:             0000007fffffffff
[    0.018000] ... fixed-purpose events:   0
[    0.018000] ... event mask:             000000000003ffff
[    0.018000] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.018000] smpboot: Booting Node   0, Processors  #1
[    0.029039] Brought up 2 CPUs
[    0.029043] smpboot: Total of 2 processors activated (12059.71 BogoMIPS)
[    0.030143] devtmpfs: initialized
[    0.030283] PM: Registering ACPI NVS region [mem 0xbfee0000-0xbfee2fff] (12288 bytes)
[    0.030283] xor: measuring software checksum speed
[    0.040003]    prefetch64-sse:  4300.000 MB/sec
[    0.050003]    generic_sse:  4252.000 MB/sec
[    0.050007] xor: using function: prefetch64-sse (4300.000 MB/sec)
[    0.050074] NET: Registered protocol family 16
[    0.050166] ACPI: bus type PCI registered
[    0.050166] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.050166] PCI: Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub with MMCONFIG support
[    0.050166] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.051314] PCI: Using configuration type 1 for base access
[    0.051415] mtrr: your CPUs had inconsistent variable MTRR settings
[    0.051415] mtrr: probably your BIOS does not setup all CPUs.
[    0.051415] mtrr: corrected configuration.
[    0.058152] bio: create slab <bio-0> at 0
[    0.075015] raid6: sse2x1   gen()  2214 MB/s
[    0.092015] raid6: sse2x1   xor()  1843 MB/s
[    0.109020] raid6: sse2x2   gen()  3265 MB/s
[    0.126008] raid6: sse2x2   xor()  1908 MB/s
[    0.143017] raid6: sse2x4   gen()  3128 MB/s
[    0.160012] raid6: sse2x4   xor()  1882 MB/s
[    0.160016] raid6: using algorithm sse2x2 gen() (3265 MB/s)
[    0.160017] raid6: .... xor() 1908 MB/s, rmw enabled
[    0.160020] raid6: using intx1 recovery algorithm
[    0.160055] ACPI: Added _OSI(Module Device)
[    0.160058] ACPI: Added _OSI(Processor Device)
[    0.160061] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.160063] ACPI: Added _OSI(Processor Aggregator Device)
[    0.161139] ACPI: EC: Look up EC in DSDT
[    0.166299] ACPI: Interpreter enabled
[    0.166323] ACPI: (supports S0 S4 S5)
[    0.166326] ACPI: Using IOAPIC for interrupt routing
[    0.166412] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.166412] ACPI: No dock devices found.
[    0.176303] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.176303] acpi PNP0A08:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.176303] acpi PNP0A08:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.176303] acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.176303] acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[    0.176303] acpi PNP0A08:00: host bridge window [mem 0xbff00000-0xfebfffff] (ignored)
[    0.176303] PCI: root bus 00: using default resources
[    0.176303] PCI host bridge to bus 0000:00
[    0.176303] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.176303] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.176303] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
[    0.176303] pci 0000:00:00.0: [8086:2770] type 00 class 0x060000
[    0.176303] pci 0000:00:01.0: [8086:2771] type 01 class 0x060400
[    0.176303] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.177070] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[    0.177091] pci 0000:00:1b.0: reg 10: [mem 0xfdff8000-0xfdffbfff 64bit]
[    0.177170] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.177249] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.177282] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.177282] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.177282] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.177282] pci 0000:00:1c.2: [8086:27d4] type 01 class 0x060400
[    0.177282] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.177282] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    0.177282] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.177282] pci 0000:00:1d.0: reg 20: [io  0xff00-0xff1f]
[    0.177282] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.178034] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.178081] pci 0000:00:1d.1: reg 20: [io  0xfe00-0xfe1f]
[    0.178171] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.178205] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.178205] pci 0000:00:1d.2: reg 20: [io  0xfd00-0xfd1f]
[    0.178205] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.178205] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.178205] pci 0000:00:1d.3: reg 20: [io  0xfc00-0xfc1f]
[    0.178205] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.178227] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.178227] pci 0000:00:1d.7: reg 10: [mem 0xfdfff000-0xfdfff3ff]
[    0.178227] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.178227] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.179038] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.179161] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.179197] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100
[    0.179197] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.179197] pci 0000:00:1f.0: address space collision: [io  0x0400-0x047f] conflicts with ACPI PM1a_EVT_BLK [??? 0x00000400-0
x00000403 flags 0x80000000]
[    0.179197] pci 0000:00:1f.0: quirk: [io  0x0480-0x04bf] claimed by ICH6 GPIO
[    0.179197] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 003f)
[    0.179197] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 001f)
[    0.179197] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
[    0.179197] pci 0000:00:1f.1: reg 10: [io  0x0000-0x0007]
[    0.179197] pci 0000:00:1f.1: reg 14: [io  0x0000-0x0003]
[    0.179197] pci 0000:00:1f.1: reg 18: [io  0x0000-0x0007]
[    0.179197] pci 0000:00:1f.1: reg 1c: [io  0x0000-0x0003]
[    0.179197] pci 0000:00:1f.1: reg 20: [io  0xfb00-0xfb0f]
[    0.179229] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.179229] pci 0000:00:1f.3: reg 20: [io  0x0500-0x051f]
[    0.180082] pci 0000:01:00.0: [10de:0291] type 00 class 0x030000
[    0.180082] pci 0000:01:00.0: reg 10: [mem 0xfa000000-0xfaffffff]
[    0.180082] pci 0000:01:00.0: reg 14: [mem 0xc0000000-0xdfffffff 64bit pref]
[    0.180082] pci 0000:01:00.0: reg 1c: [mem 0xfb000000-0xfbffffff 64bit]
[    0.180088] pci 0000:01:00.0: reg 24: [io  0xbf00-0xbf7f]
[    0.180098] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.180172] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.180172] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.180172] pci 0000:00:01.0:   bridge window [io  0xb000-0xbfff]
[    0.180172] pci 0000:00:01.0:   bridge window [mem 0xfa000000-0xfcffffff]
[    0.180172] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xdfffffff 64bit pref]
[    0.180172] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.180172] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.180172] pci 0000:00:1c.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.180172] pci 0000:00:1c.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.180172] pci 0000:03:00.0: [8086:108b] type 00 class 0x020000
[    0.180172] pci 0000:03:00.0: reg 10: [mem 0xfdee0000-0xfdefffff]
[    0.180172] pci 0000:03:00.0: reg 14: [mem 0xfdd00000-0xfddfffff]
[    0.180172] pci 0000:03:00.0: reg 18: [io  0xcf00-0xcf1f]
[    0.180281] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    0.181029] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.181044] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.181050] pci 0000:00:1c.2:   bridge window [io  0xc000-0xcfff]
[    0.181055] pci 0000:00:1c.2:   bridge window [mem 0xfdd00000-0xfdefffff]
[    0.181062] pci 0000:00:1c.2:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.181106] pci 0000:04:01.0: [1095:0680] type 00 class 0x010400
[    0.181106] pci 0000:04:01.0: reg 10: [io  0xef00-0xef07]
[    0.181106] pci 0000:04:01.0: reg 14: [io  0xee00-0xee03]
[    0.181106] pci 0000:04:01.0: reg 18: [io  0xed00-0xed07]
[    0.181106] pci 0000:04:01.0: reg 1c: [io  0xec00-0xec03]
[    0.181107] pci 0000:04:01.0: reg 20: [io  0xeb00-0xeb0f]
[    0.181118] pci 0000:04:01.0: reg 24: [mem 0xfdaff000-0xfdaff0ff]
[    0.181131] pci 0000:04:01.0: reg 30: [mem 0x00000000-0x0007ffff pref]
[    0.181164] pci 0000:04:01.0: supports D1 D2
[    0.181200] pci 0000:04:03.0: [1106:3044] type 00 class 0x0c0010
[    0.181200] pci 0000:04:03.0: reg 10: [mem 0xfdafe000-0xfdafe7ff]
[    0.181200] pci 0000:04:03.0: reg 14: [io  0xea00-0xea7f]
[    0.181200] pci 0000:04:03.0: supports D2
[    0.181200] pci 0000:04:03.0: PME# supported from D2 D3hot D3cold
[    0.181200] pci 0000:04:04.0: [1106:3164] type 00 class 0x01018f
[    0.181200] pci 0000:04:04.0: reg 10: [io  0xe900-0xe907]
[    0.181200] pci 0000:04:04.0: reg 14: [io  0xe800-0xe803]
[    0.181200] pci 0000:04:04.0: reg 18: [io  0xe700-0xe707]
[    0.181200] pci 0000:04:04.0: reg 1c: [io  0xe600-0xe603]
[    0.181200] pci 0000:04:04.0: reg 20: [io  0xe500-0xe50f]
[    0.181211] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.181211] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.181211] pci 0000:00:1e.0:   bridge window [mem 0xfda00000-0xfdafffff]
[    0.181211] pci 0000:00:1e.0:   bridge window [mem 0xfd900000-0xfd9fffff 64bit pref]
[    0.181211] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.181211] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[    0.181211] pci_bus 0000:00: on NUMA node 0
[    0.181211] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.181211] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.182415] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 *7 9 10 11 12 14 15)
[    0.182521] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[    0.182627] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.182731] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 9 10 11 12 14 15)
[    0.182837] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.182943] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.183077] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.183182] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 *4 5 7 9 10 11 12 14 15)
[    0.183375] acpi root: \_SB_.PCI0 notify handler is installed
[    0.183375] Found 1 acpi root devices
[    0.184062] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.184062] vgaarb: loaded
[    0.184062] vgaarb: bridge control possible 0000:01:00.0
[    0.184146] SCSI subsystem initialized
[    0.184146] ACPI: bus type ATA registered
[    0.184146] libata version 3.00 loaded.
[    0.184146] pps_core: LinuxPPS API ver. 1 registered
[    0.184146] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.184146] PTP clock support registered
[    0.185039] PCI: Using ACPI for IRQ routing
[    0.191776] PCI: pci_cache_line_size set to 64 bytes
[    0.191842] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[    0.191846] e820: reserve RAM buffer [mem 0xbfedf800-0xbfffffff]
[    0.192222] hpet clockevent registered
[    0.192229] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.192235] Switching to clocksource hpet
[    0.192235] AppArmor: AppArmor Filesystem Enabled
[    0.192235] pnp: PnP ACPI init
[    0.192235] ACPI: bus type PNP registered
[    0.192487] system 00:00: [io  0x0b78-0x0b7b] has been reserved
[    0.192493] system 00:00: [io  0x0f78-0x0f7b] has been reserved
[    0.192497] system 00:00: [io  0x0a78-0x0a7b] has been reserved
[    0.192500] system 00:00: [io  0x0e78-0x0e7b] has been reserved
[    0.192503] system 00:00: [io  0x0bbc-0x0bbf] has been reserved
[    0.192507] system 00:00: [io  0x0fbc-0x0fbf] has been reserved
[    0.192510] system 00:00: [io  0x04d0-0x04d1] has been reserved
[    0.192513] system 00:00: [io  0x0294-0x0297] has been reserved
[    0.192517] system 00:00: [io  0x0800-0x087f] has been reserved
[    0.192520] system 00:00: [io  0x0880-0x088f] has been reserved
[    0.192525] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.192545] pnp 00:01: [dma 4]
[    0.192615] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.192710] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.192789] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.192875] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.193600] system 00:05: [io  0x0400-0x04bf] could not be reserved
[    0.193606] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.193702] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[    0.194102] system 00:07: [mem 0xe0000000-0xefffffff] has been reserved
[    0.194107] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.194419] system 00:08: [mem 0x000d4600-0x000d7fff] has been reserved
[    0.194425] system 00:08: [mem 0x000f0000-0x000f7fff] could not be reserved
[    0.194428] system 00:08: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.194432] system 00:08: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.194435] system 00:08: [mem 0xbfee0000-0xbfefffff] could not be reserved
[    0.194440] system 00:08: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.194445] system 00:08: [mem 0x00100000-0xbfedffff] could not be reserved
[    0.194448] system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.194452] system 00:08: [mem 0xfed13000-0xfed1dfff] has been reserved
[    0.194455] system 00:08: [mem 0xfed20000-0xfed8ffff] has been reserved
[    0.194459] system 00:08: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.194462] system 00:08: [mem 0xffb00000-0xffb7ffff] has been reserved
[    0.194465] system 00:08: [mem 0xfff00000-0xffffffff] has been reserved
[    0.194469] system 00:08: [mem 0x000e0000-0x000effff] has been reserved
[    0.194472] system 00:08: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.194484] pnp: PnP ACPI: found 9 devices
[    0.194487] ACPI: bus type PNP unregistered
[    0.205686] pci 0000:00:1f.0: BAR 13: [io  0x0400-0x047f] has bogus alignment
[    0.205697] pci 0000:01:00.0: BAR 6: assigned [mem 0xfc000000-0xfc01ffff pref]
[    0.205702] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.205706] pci 0000:00:01.0:   bridge window [io  0xb000-0xbfff]
[    0.205711] pci 0000:00:01.0:   bridge window [mem 0xfa000000-0xfcffffff]
[    0.205716] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xdfffffff 64bit pref]
[    0.205722] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.205726] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.205732] pci 0000:00:1c.0:   bridge window [mem 0xfdb00000-0xfdbfffff]
[    0.205737] pci 0000:00:1c.0:   bridge window [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.205745] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.205749] pci 0000:00:1c.2:   bridge window [io  0xc000-0xcfff]
[    0.205755] pci 0000:00:1c.2:   bridge window [mem 0xfdd00000-0xfdefffff]
[    0.205760] pci 0000:00:1c.2:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.205770] pci 0000:04:01.0: BAR 6: assigned [mem 0xfd900000-0xfd97ffff pref]
[    0.205773] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    0.205778] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.205784] pci 0000:00:1e.0:   bridge window [mem 0xfda00000-0xfdafffff]
[    0.205789] pci 0000:00:1e.0:   bridge window [mem 0xfd900000-0xfd9fffff 64bit pref]
[    0.206106] pci 0000:00:1e.0: setting latency timer to 64
[    0.206113] pci_bus 0000:00: resource 4 [io  0x0000-0xffff]
[    0.206119] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
[    0.206123] pci_bus 0000:01: resource 0 [io  0xb000-0xbfff]
[    0.206126] pci_bus 0000:01: resource 1 [mem 0xfa000000-0xfcffffff]
[    0.206129] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xdfffffff 64bit pref]
[    0.206132] pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
[    0.206135] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff]
[    0.206138] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref]
[    0.206141] pci_bus 0000:03: resource 0 [io  0xc000-0xcfff]
[    0.206144] pci_bus 0000:03: resource 1 [mem 0xfdd00000-0xfdefffff]
[    0.206147] pci_bus 0000:03: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.206150] pci_bus 0000:04: resource 0 [io  0xe000-0xefff]
[    0.206153] pci_bus 0000:04: resource 1 [mem 0xfda00000-0xfdafffff]
[    0.206155] pci_bus 0000:04: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref]
[    0.206158] pci_bus 0000:04: resource 4 [io  0x0000-0xffff]
[    0.206162] pci_bus 0000:04: resource 5 [mem 0x00000000-0xfffffffff]
[    0.206230] NET: Registered protocol family 2
[    0.206493] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    0.206649] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.206799] TCP: Hash tables configured (established 32768 bind 32768)
[    0.206848] TCP: reno registered
[    0.206853] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.206884] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.206979] NET: Registered protocol family 1
[    0.207125] RPC: Registered named UNIX socket transport module.
[    0.207128] RPC: Registered udp transport module.
[    0.207130] RPC: Registered tcp transport module.
[    0.207132] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.208162] pci 0000:01:00.0: Boot video device
[    0.208174] PCI: CLS mismatch (32 != 4), using 64 bytes
[    0.208252] Trying to unpack rootfs image as initramfs...
[    2.944401] Freeing initrd memory: 8572k freed
[    2.985951] audit: initializing netlink socket (disabled)
[    2.985969] type=2000 audit(1502204361.984:1): initialized
[    3.000125] bounce pool size: 64 pages
[    3.004136] VFS: Disk quotas dquot_6.5.2
[    3.004171] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    3.006141] NFS: Registering the id_resolver key type
[    3.006158] Key type id_resolver registered
[    3.006161] Key type id_legacy registered
[    3.006178] msgmni has been set to 6022
[    3.006348] async_tx: api initialized (async)
[    3.006472] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    3.006477] io scheduler noop registered
[    3.006479] io scheduler deadline registered
[    3.006494] io scheduler cfq registered (default)
[    3.007701] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    3.008444] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    3.009546] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[    3.966027] tsc: Refined TSC clocksource calibration: 3014.772 MHz
[    3.966036] Switching to clocksource tsc
[    4.451928] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    4.460347] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 8250
[    4.619183] brd: module loaded
[    4.631551] ACPI Warning: 0x0000000000000428-0x000000000000042F SystemIO conflicts with Region \PM2S 1 (20130328/utaddress-24
9)
[    4.631564] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    4.631569] Unknown LPC device 27b8
[    4.631572] ACPI Warning: 0x00000000000004B0-0x00000000000004BF SystemIO conflicts with Region \GPO2 1 (20130328/utaddress-24
9)
[    4.631577] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    4.631580] ACPI Warning: 0x0000000000000480-0x00000000000004AF SystemIO conflicts with Region \GPO_ 1 (20130328/utaddress-24
9)
[    4.631585] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    4.631587] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    4.642057] Loading iSCSI transport class v2.0-870.
[    4.695680] rdac: device handler registered
[    4.732710] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    4.737251] serio: i8042 KBD port at 0x60,0x64 irq 1
[    4.737262] serio: i8042 AUX port at 0x60,0x64 irq 12
[    4.742995] rtc_cmos 00:02: RTC can wake from S4
[    4.747454] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    4.747492] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs
[    4.751263] i2c /dev entries driver
[    4.755999] md: linear personality registered for level -1
[    4.756010] md: raid0 personality registered for level 0
[    4.756013] md: raid1 personality registered for level 1
[    4.756015] md: raid10 personality registered for level 10
[    4.760499] md: raid6 personality registered for level 6
[    4.760504] md: raid5 personality registered for level 5
[    4.760507] md: raid4 personality registered for level 4
[    4.760509] md: raidF1 personality registered for level 45
[    4.762140] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[    4.762146] cpuidle: using governor ladder
[    4.762149] cpuidle: using governor menu
[    4.762262] TCP: cubic registered
[    4.762266] NET: Registered protocol family 17
[    4.762308] Key type dns_resolver registered
[    4.780431] registered taskstats version 1
[    4.784116] rtc_cmos 00:02: setting system clock to 2017-08-08 14:59:24 UTC (1502204364)
[    4.785055] Freeing unused kernel memory: 760k freed
[    4.785397] Write protecting the kernel read-only data: 8192k
[    4.785656] Freeing unused kernel memory: 1336k freed
[    4.787855] Freeing unused kernel memory: 504k freed
[    4.877460] ACPI: bus type USB registered
[    4.878692] usbcore: registered new interface driver usbfs
[    4.879840] usbcore: registered new interface driver hub
[    4.883092] usbcore: registered new interface driver ethub
[    4.887532] usbcore: registered new device driver usb
[    4.913821] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.924081] ehci-pci: EHCI PCI platform driver
[    4.924257] ehci-pci 0000:00:1d.7: setting latency timer to 64
[    4.924274] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    4.924284] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    4.928197] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    4.928224] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdfff000
[    4.934016] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    4.934406] hub 1-0:1.0: USB hub found
[    4.934414] hub 1-0:1.0: 8 ports detected
[    4.961016] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.975237] uhci_hcd: USB Universal Host Controller Interface driver
[    4.975414] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    4.975420] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    4.975430] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    4.975464] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff00
[    4.976896] hub 2-0:1.0: USB hub found
[    4.976908] hub 2-0:1.0: 2 ports detected
[    4.977121] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    4.977126] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    4.977135] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    4.977180] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fe00
[    4.978705] hub 3-0:1.0: USB hub found
[    4.978714] hub 3-0:1.0: 2 ports detected
[    4.978911] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    4.978917] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    4.978925] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    4.978970] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fd00
[    4.984129] hub 4-0:1.0: USB hub found
[    4.984143] hub 4-0:1.0: 2 ports detected
[    4.984376] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    4.984382] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    4.984392] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    4.984442] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[    4.991122] hub 5-0:1.0: USB hub found
[    4.991134] hub 5-0:1.0: 2 ports detected
[    5.106768] usbcore: registered new interface driver usb-storage
[    5.140771] VMware PVSCSI driver - version 1.0.2.0-k
[    5.154251] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    5.169240] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    5.215136] Fusion MPT base driver 3.04.20
[    5.215141] Copyright (c) 1999-2008 LSI Corporation
[    5.236020] Fusion MPT SPI Host driver 3.04.20
[    5.250229] Fusion MPT SAS Host driver 3.04.20
[    5.263624] Fusion MPT misc device (ioctl) driver 3.04.20
[    5.263771] mptctl: Registered with Fusion MPT base driver
[    5.263776] mptctl: /dev/mptctl @ (major,minor=10,220)
[    5.277475] ata_piix 0000:00:1f.1: version 2.13
[    5.277662] ata_piix 0000:00:1f.1: setting latency timer to 64
[    5.297050] scsi0 : ata_piix
[    5.302569] scsi1 : ata_piix
[    5.306767] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfb00 irq 14
[    5.306773] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfb08 irq 15
[    5.463011] ata1: Read current link speed fail, retry 1
[    5.469009] ata1: Read current link speed fail, retry 2
[    5.475009] ata1: Read current link speed fail, retry 3
[    5.481009] ata2: Read current link speed fail, retry 1
[    5.487008] ata2: Read current link speed fail, retry 2
[    5.493008] ata2: Read current link speed fail, retry 3
[    5.508246] ata1.00: ATA-5: WDC WD1000BB-75CHE0, 22.04A22, max UDMA/100
[    5.508253] ata1.00: 195371568 sectors, multi 16: LBA
[    5.508477] ata1.01: ATA-7: Maxtor 6Y120L0, YAR41BW0, max UDMA/133
[    5.508480] ata1.01: 240121728 sectors, multi 16: LBA
[    5.515103] ata1.00: configured for UDMA/100
[    5.521355] ata1.01: configured for UDMA/100
[    5.521379] ata1.00: Find SSD disks. [WDC WD1000BB-75CHE0]
[    5.523941] scsi 0:0:0:0: Direct-Access     WDC      WD1000BB-75CHE0          22.0 PQ: 0 ANSI: 5
[    5.525441] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[    5.525511] sd 0:0:0:0: [sda] Write Protect is off
[    5.525516] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.525545] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.551027] usb 1-6: new high-speed USB device number 3 using ehci-pci
[    5.553687]  sda: sda1 sda2
[    5.554464] scsi 0:0:1:0: Direct-Access     Maxtor   6Y120L0                  YAR4 PQ: 0 ANSI: 5
[    5.555412] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.557834] want_idx 0 index 1. delay and reget
[    5.689061] usb-storage 1-6:1.0: USB Mass Storage device detected
[    5.690145] scsi2 : usb-storage 1-6:1.0
[    5.918016] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[    6.112543] Got empty serial number. Generate serial number from product.
[    6.557015] want_idx 0 index 1
[    6.557021] want_idx 0 index 1. delay and reget
[    6.694087] scsi 2:0:0:0: Direct-Access     Flash    Drive SM_USB20           1100 PQ: 0 ANSI: 0 CCS
[    6.696228] sd 2:0:0:0: [sdu] 2030592 512-byte logical blocks: (1.03 GB/991 MiB)
[    6.696726] sd 2:0:0:0: Embedded Enclosure Device
[    6.697221] sd 2:0:0:0: [sdu] Write Protect is off
[    6.697228] sd 2:0:0:0: [sdu] Mode Sense: 43 00 00 00
[    6.822020] usb 1-6: reset high-speed USB device number 3 using ehci-pci
[    7.089014] usb 1-6: reset high-speed USB device number 3 using ehci-pci
[    7.356014] usb 1-6: reset high-speed USB device number 3 using ehci-pci
[    7.557012] want_idx 0 index 1
[    7.557016] want_idx 0 index 1. delay and reget
[    7.623014] usb 1-6: reset high-speed USB device number 3 using ehci-pci
[    7.759254] sd 2:0:0:0: Wrong diagnostic page; asked for 1 got 0
[    7.759392] sd 2:0:0:0: Failed to get diagnostic page 0xffffffea
[    7.759527] sd 2:0:0:0: Failed to bind enclosure -19
[    7.760636] sd 2:0:0:0: [sdu] No Caching mode page found
[    7.760766] sd 2:0:0:0: [sdu] Assuming drive cache: write through
[    7.765000] sd 2:0:0:0: [sdu] No Caching mode page found
[    7.765151] sd 2:0:0:0: [sdu] Assuming drive cache: write through
[    7.775396]  sdu: sdu1 sdu2 sdu3
[    7.780630] sd 2:0:0:0: [sdu] No Caching mode page found
[    7.780759] sd 2:0:0:0: [sdu] Assuming drive cache: write through
[    7.780902] sd 2:0:0:0: [sdu] Attached SCSI removable disk
[    8.557016] want_idx 0 index 1
[    8.557022] want_idx 0 index 1. delay and reget
[    9.557011] want_idx 0 index 1
[    9.557014] want_idx 0 index 1. delay and reget
[   10.557011] want_idx 0 index 1
[   10.557014] want_idx 0 index 1. delay and reget
[   11.557011] want_idx 0 index 1
[   11.557014] want_idx 0 index 1. delay and reget
[   12.557011] want_idx 0 index 1
[   12.557014] want_idx 0 index 1. delay and reget
[   13.557011] want_idx 0 index 1
[   13.557014] want_idx 0 index 1. delay and reget
[   14.557010] want_idx 0 index 1
[   14.557013] want_idx 0 index 1. delay and reget
[   15.557011] want_idx 0 index 1
[   15.557014] want_idx 0 index 1. delay and reget
[   16.557010] want_idx 0 index 1
[   16.557013] want_idx 0 index 1. delay and reget
[   17.557010] want_idx 0 index 1
[   17.557013] want_idx 0 index 1. delay and reget
[   18.557011] want_idx 0 index 1
[   18.557014] want_idx 0 index 1. delay and reget
[   19.557010] want_idx 0 index 1
[   19.557014] want_idx 0 index 1. delay and reget
[   20.557012] want_idx 0 index 1
[   20.557294] sd 0:0:1:0: [sdb] 240121728 512-byte logical blocks: (122 GB/114 GiB)
[   20.557364] sd 0:0:1:0: [sdb] Write Protect is off
[   20.557369] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[   20.557398] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   20.580392]  sdb: sdb1 sdb2
[   20.582021] sd 0:0:1:0: [sdb] Attached SCSI disk
[   20.611720] megasas: 06.506.00.00-rc1 Sat. Feb. 9 17:00:00 PDT 2013
[   20.641742] mpt2sas version 20.00.00.00 loaded
[   20.663336] mpt3sas version 01.100.01.00 loaded
[   20.680059] pata_via: Unknown symbol syno_libata_index_get (err 0)
[   20.685297] bromolow_synobios: module license 'Synology Inc.' taints kernel.
[   20.685304] Disabling lock debugging due to kernel taint
[   20.685942] 2017-8-8 14:59:40 UTC
[   20.685948] synobios: load, major number 201
[   20.685953] Brand: Synology
[   20.685956] Model: DS-3615xs
[   20.685960] set group disks wakeup number to 4, spinup time deno 7
[   21.186027] synobios cpu_arch proc entry initialized
[   21.186033] synobios crypto_hw proc entry initialized
[   21.186039] synobios syno_platform proc entry initialized
[   21.198913] synobios: unload
[   21.211247] md: Autodetecting RAID arrays.
[   21.274132] md: Scanned 4 and added 4 devices.
[   21.274138] md: autorun ...
[   21.274141] md: considering sda1 ...
[   21.274147] md:  adding sda1 ...
[   21.274150] md: sda2 has different UUID to sda1
[   21.274155] md:  adding sdb1 ...
[   21.274158] md: sdb2 has different UUID to sda1
[   21.274166] md: created md0
[   21.274169] md: bind<sdb1>
[   21.274189] md: bind<sda1>
[   21.274202] md: running: <sda1><sdb1>
[   21.274471] md/raid1:md0: active with 2 out of 12 mirrors
[   21.274501] md0: detected capacity change from 0 to 2549940224
[   21.274652] md: considering sda2 ...
[   21.274659] md:  adding sda2 ...
[   21.274663] md:  adding sdb2 ...
[   21.275986] md: created md1
[   21.275992] md: bind<sdb2>
[   21.276018] md: bind<sda2>
[   21.276033] md: running: <sda2><sdb2>
[   21.281086] md/raid1:md1: active with 2 out of 12 mirrors
[   21.281126] md1: detected capacity change from 0 to 2147418112
[   21.283104] md: ... autorun DONE.
[   21.321535]  md0: unknown partition table
[   23.710087] EXT4-fs (md0): barriers disabled
[   23.722984] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts:
[   28.213423] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: barrier=1
[   31.051333] EXT4-fs (md0): re-mounted. Opts: (null)
[   35.849317] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   35.849420] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   35.849517] sd 0:0:1:0: Attached scsi generic sg2 type 0
[   36.083018] usb 1-6: reset high-speed USB device number 3 using ehci-pci
[   36.435269]  md1: unknown partition table
[   36.636470] Adding 2097084k swap on /dev/md1.  Priority:-1 extents:1 across:2097084k
[   37.206520] zram: module is from the staging directory, the quality is unknown, you have been warned.
[   37.207598] zram: Created 2 device(s) ...
[   37.230226] Adding 925692k swap on /dev/zram0.  Priority:1 extents:1 across:925692k SS
[   37.247353] Adding 925692k swap on /dev/zram1.  Priority:1 extents:1 across:925692k SS
[   38.295246] NET: Registered protocol family 10
[   38.355799] sit: IPv6 over IPv4 tunneling driver
[   39.035866] init: syno-auth-check main process (5168) killed by TERM signal
[   40.294964] fuse init (API version 7.22)
[   40.331876] dca service started, version 1.12.1
[   40.339705] e1000e: Intel(R) PRO/1000 Network Driver - 3.3.4-NAPI
[   40.339710] e1000e: Copyright(c) 1999 - 2016 Intel Corporation.
[   40.339934] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[   40.339976] e1000e 0000:03:00.0: irq 43 for MSI/MSI-X
[   40.388359] e1000e 0000:03:00.0: Warning: detected DSPD enabled in EEPROM
[   40.391172] systemd-udevd[5465]: starting version 204
[   40.446646] e1000e 0000:03:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:13:d3:39:0f:32
[   40.446653] e1000e 0000:03:00.0 eth0: Intel(R) PRO/1000 Network Connection
[   40.446668] e1000e 0000:03:00.0 eth0: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF
[   40.495948] Intel(R) Gigabit Ethernet Network Driver - version 5.3.5.3
[   40.495954] Copyright (c) 2007-2015 Intel Corporation.
[   40.557949] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.4.6
[   40.557954] Copyright(c) 1999 - 2016 Intel Corporation.
[   40.558043] ixgbe unsupported_sfp_notify proc entry initialized
[   40.721020] i40e: Intel(R) 40-10 Gigabit Ethernet Connection Network Driver - version 1.5.19
[   40.721027] i40e: Copyright(c) 2013 - 2016 Intel Corporation.
[   40.866364] tn40xx: Tehuti Network Driver, 0.3.6.12.3
[   40.982555] Loading modules backported from Linux version v3.18.1-0-g39ca484
[   40.982561] Backport generated by backports.git v3.18.1-1-0-g5e9ec4c
[   41.140205] Compat-mlnx-ofed backport release: cd30181
[   41.140210] Backport based on mlnx_ofed/mlnx_rdma.git cd30181
[   41.140212] compat.git: mlnx_ofed/mlnx_rdma.git
[   43.538111] bnx2x: QLogic 5771x/578xx 10/20-Gigabit Ethernet Driver bnx2x 1.713.00 ($DateTime: 2015/07/28 00:13:30 $)
[   46.381726] bio: create slab <bio-1> at 1
[   46.381943] Btrfs loaded
[   46.447846] jme: JMicron JMC2XX ethernet driver version 1.0.8
[   46.461422] sky2: driver version 1.30
[   46.475088] pch_gbe: EG20T PCH Gigabit Ethernet Driver - version 1.01
[   46.489498] QLogic 1/10 GbE Converged/Intelligent Ethernet Driver v5.2.42
[   46.503621] QLogic/NetXen Network Driver v4.0.80
[   46.511107] Solarflare NET driver v3.2
[   46.518493] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[   46.518499] e1000: Copyright (c) 1999-2006 Intel Corporation.
[   46.525519] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[   46.532339] VMware vmxnet3 virtual NIC driver - version 1.1.30.0-k-NAPI
[   46.553329] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.16 (Dec 05, 2012)
[   46.599255] usbcore: registered new interface driver ax88179_178a
[   46.606404] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[   46.606414] ACPI: Power Button [PWRB]
[   46.606493] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[   46.606498] ACPI: Power Button [PWRF]
[   46.627660] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[   46.634938] 8139too: 8139too Fast Ethernet driver 0.9.28
[   46.641918] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[   46.641924] e100: Copyright(c) 1999-2006 Intel Corporation
[   46.669469] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[   46.669475] via_rhine: Broken BIOS detected, avoid_D3 enabled
[   46.826453] 2017-8-8 15:0:6 UTC
[   46.826460] synobios: load, major number 201
[   46.826465] Brand: Synology
[   46.826469] Model: DS-3615xs
[   46.826472] set group disks wakeup number to 4, spinup time deno 7
[   47.327024] synobios cpu_arch proc entry initialized
[   47.327031] synobios crypto_hw proc entry initialized
[   47.327035] synobios syno_platform proc entry initialized
[   48.134870] e1000e 0000:03:00.0: irq 43 for MSI/MSI-X
[   48.235110] e1000e 0000:03:00.0: irq 43 for MSI/MSI-X
[   48.235760] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   51.181652] usbcore: registered new interface driver usblp
[   51.243978] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   51.244127] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   51.249106] usbcore: registered new interface driver usbhid
[   51.249112] usbhid: USB HID core driver
[   51.322463] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input2
[   51.322484] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-1/inpu
t0
[   51.322867] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input3
[   51.322877] Get empty minor:104
[   51.324892] hid-generic 0003:046D:C52B.0002: input,hiddev0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
/input1
[   51.329028] Get empty minor:105
[   51.329138] hid-generic 0003:046D:C52B.0003: hiddev0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1/inpu
t2
[   52.629245] init: dhcp-client (eth0) main process (8235) killed by TERM signal
[   56.075308] ata1.00: configured for UDMA/100
[   56.081336] ata1.01: configured for UDMA/100
[   56.081344] ata1: EH complete
[   56.176205] ata1.00: configured for UDMA/100
[   56.182336] ata1.01: configured for UDMA/100
[   56.182347] ata1: EH complete
[   60.601041] iSCSI:target_core_rodsp_server.c:1017:rodsp_server_init RODSP server started, login_key(0013d3390f32).
[   61.017801] iSCSI:extent_pool.c:749:ep_init syno_extent_pool successfully initialized
[   61.073426] iSCSI:target_core_device.c:561:se_dev_align_max_sectors Rounding down aligned max_sectors from 4294967295 to 4294
967288
[   61.080818] iSCSI:target_core_lunbackup.c:358:init_io_buffer_head 512 buffers allocated, total 2097152 bytes successfully
[   61.296491] iSCSI:target_core_file.c:89:fd_attach_hba RODSP plugin for fileio is enabled.
[   61.296511] iSCSI:target_core_ep.c:861:ep_attach_hba RODSP plugin for epio is enabled.
[   61.296517] iSCSI:target_core_ep.c:868:ep_attach_hba ODX Token Manager is enabled.
[   62.307417] loop: module loaded
[   67.546205] ata1.00: configured for UDMA/100
[   67.552355] ata1.01: configured for UDMA/100
[   67.552363] ata1: EH complete
[   67.574305] ata1.00: configured for UDMA/100
[   67.580348] ata1.01: configured for UDMA/100
[   67.580355] ata1: EH complete
 

Hide  

Share this post


Link to post
Share on other sites

UPDATE: Looks like the issue is also faced in Spanish section see:

module loads to late in the startup process, seems to be the issue.

Share this post


Link to post
Share on other sites
6 hours ago, madhits45 said:

UPDATE: Looks like the issue is also faced in Spanish section see:

module loads to late in the startup process, seems to be the issue.

 

with "pata_via: Unknown symbol syno_libata_index_get (err 0)" i was more thinking there is a problem between the running kernel and the module loaded, as both where compiled with the same source (15047)  it might be that sysnolgy modified some drivers (or driver classes) and others did not received that mod (because they never intended to use them), it might be possible to search in the kernel source for syno_libata_index_get but as i'm not a c++ coder there is not much i could do about it

 

Share this post


Link to post
Share on other sites
44 minutes ago, IG-88 said:

 

with "pata_via: Unknown symbol syno_libata_index_get (err 0)" i was more thinking there is a problem between the running kernel and the module loaded, as both where compiled with the same source (15047)  it might be that sysnolgy modified some drivers (or driver classes) and others did not received that mod (because they never intended to use them), it might be possible to search in the kernel source for syno_libata_index_get but as i'm not a c++ coder there is not much i could do about it

 

ohh no, maybe Jun can help with this since it seems pretty high level.

Share this post


Link to post
Share on other sites
18 hours ago, madhits45 said:

ohh no, maybe Jun can help with this since it seems pretty high level.

beside i'm just guessing, pata drivers are not that importand, pata/ide drives have limited capaticy afaik the biggest drives ever produced had 750GB, most people use 2-4TB drives or evven bigger

Share this post


Link to post
Share on other sites
9 hours ago, IG-88 said:

beside i'm just guessing, pata drivers are not that importand, pata/ide drives have limited capaticy afaik the biggest drives ever produced had 750GB, most people use 2-4TB drives or evven bigger

I know its actually the controller I'm interested in because I have a few IDE drives but also sata to IDE adapters that allow me to use 1tb drives with this via raid controller. So I have 2x 650gb IDE drives and 2x 1tb drives that work with sata to IDE adapters on this via controller. The board also has 4 sata ports but they only support unto 500gb drives which is odd, since the via can handle larger drives with the sata to IDE adapter.

Share this post


Link to post
Share on other sites
On 8/10/2017 at 5:08 AM, madhits45 said:

I know its actually the controller I'm interested in because I have a few IDE drives but also sata to IDE adapters that allow me to use 1tb drives with this via raid controller. So I have 2x 650gb IDE drives and 2x 1tb drives that work with sata to IDE adapters on this via controller. The board also has 4 sata ports but they only support unto 500gb drives which is odd, since the via can handle larger drives with the sata to IDE adapter.

i would expect this to be a driver issue, did you try a >500GB drive on the sata with 6.1? if the sata's are detected and have a propper driver the i would expect them to work with drives bigger then 500GB

Share this post


Link to post
Share on other sites
22 hours ago, IG-88 said:

i would expect this to be a driver issue, did you try a >500GB drive on the sata with 6.1? if the sata's are detected and have a propper driver the i would expect them to work with drives bigger then 500GB

The problem is i have to many sata drives and just a few IDE, so the mix works we'll the way it is. If I was to move the 1tb drives to the sata controller id just end up with the 500gb drives on the IDE. So it really does not matter. This is my secondary nas, I have a newer machine that I expect better support on. This one is simply duplicate critical files for disaster recovery.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.