xpenology DSM 7.2 rr v25.1.3 3ware 9650SE-8LPML drive not showing in DSM when booted how to passthrough or show all signal disk drives (8)

[bnokes]

xpenology DSM 7.2 rr v25.1.3 3ware 9650SE-8LPML drive not showing in DSM when booted how to passthrough or show all signal disk drives (8)

 

CPU xeon x5675

 

Only see the drives when I boot in bios area before OS loads and I see all the drive the controller see them and when I go in ALT+3 and change settings, every change I do still doesn't make DSM see the drives. Does anyone know any commands that can help be make the OS see the drives.

every time I boot into DSM I do not see all the drives connected to 3ware 9650SE-8LPML. I have tried the command lsblk and it doesn't work, fdisk -l still doesn't show the disk.

 

I will need command list help if anyone can help with this.

 

Also in the RR setup I went in and added driver that looked like they would help with this controller, but nothing helped get those drive to be seen by the OS DSM

[Peter Suh]

Looking at the latest version of rr,
the module required for the controller has been removed.
It is estimated to be 3w-9xxx.ko.

 

This module seems to have existed in the early days of loader development, but I don't know why it disappeared now.
Fortunately, my mshell still includes the 3w-9xxx.ko module.

https://github.com/PeterSuh-Q3/arpl-modules/tree/main/broadwellnk-4.4.302

Please go to the latest release link in my profile and try changing it to my loader.
Since it is a first-generation Xeon in terms of Intel generation, DS918+ will likely panic.
Please try DS3622xs+.

 

If the module included in this link does not work,
I will recompile it based on the latest source provided by Broadcom.

https://www.broadcom.com/support/download-search?pf=Legacy+RAID+Controllers&pg=Legacy+Products&pn=3ware+9650SE-2LP

Edited February 1 by Peter Suh

[Peter Suh]

I checked the code for compiling the module and confirmed that the latest version, 2.26.02.014, is already being used.

 

https://github.com/PeterSuh-Q3/arpl-modules/blob/main/src/4.x/drivers/scsi/3w-9xxx.c

 

https://docs.broadcom.com/docs/12349203

3w-9xxx-2.6.37.tgz

 

 

However, there may be differences between the two sources, leaving room for compilation and improvement.

 

 

Edited February 1 by Peter Suh

[Peter Suh]

@bnokes

 

Did you see my answer?

[bearcat]

On 1/29/2025 at 4:26 AM, bnokes said:

3ware 9650SE-8LPML drive not showing in DSM

 

1 - Has it been re-flashed to IT-mode?

2 - If not, have you tried configuring each disk as a RAID0 from the 3ware BIOS?

[bnokes]

I see this now. I will try and update and see if this will work thank you for your time and help.

 

I did also download these files to see if I can just add them somewhere were xpenology dsm will fine them, 3w-9xxx.c, 3w-9xxx.h, 3w-9xxx.ko, 3w-sas.ko, 3w-xxxx.ko, driver_linux-3ware_95xx-96xx_9-5-5-1codeset.zip. I know nothing about any of this.

 

I would like to get this card working. I do not want to use the RAID controller part.

 

I would like to make this in to HBA passthrough mode. I can't seem to find any way to do so. Online talks are that this can't be used as HBA but only JBOD mode. I think the only thing is to put it into JBOD mode, unless anyone else has any other better ways to send the disks over to DSM.

 

bearcat how do I flash it into IT-mode? do you know?

 

I have been playing with the settings. I will have to check that more.

 

 

Thank you all for all your time and help with this matter.

[Peter Suh]

43 minutes ago, bnokes said:

I see this now. I will try and update and see if this will work thank you for your time and help.

 

I did also download these files to see if I can just add them somewhere were xpenology dsm will fine them, 3w-9xxx.c, 3w-9xxx.h, 3w-9xxx.ko, 3w-sas.ko, 3w-xxxx.ko, driver_linux-3ware_95xx-96xx_9-5-5-1codeset.zip. I know nothing about any of this.

 

I would like to get this card working. I do not want to use the RAID controller part.

 

I would like to make this in to HBA passthrough mode. I can't seem to find any way to do so. Online talks are that this can't be used as HBA but only JBOD mode. I think the only thing is to put it into JBOD mode, unless anyone else has any other better ways to send the disks over to DSM.

 

bearcat how do I flash it into IT-mode? do you know?

 

I have been playing with the settings. I will have to check that more.

 

 

Thank you all for all your time and help with this matter.

 

Since RR doesn't have the 3ware module yet, I applied this module to my mshell to be included by default.

Please note that the c source location I provided is not meant to be used directly.

 

mshell is another loader like RR.
A menu-style loader build similar to RR is prepared.
You can easily build the loader by proceeding in order of the menu.

 

https://github.com/PeterSuh-Q3/tinycore-redpill/releases

 

 

The recognition of the 3ware module I created should be a priority over your additional requirements.

 

Edited April 8 by Peter Suh

[bnokes]

I have RR and using, will this destroy all that is on my install and everything that I set up with the RR?

 

 

maybe ill try to just add your 3ware some how, think i found one that I tried and didn't see if work. 

 

what is this supports to do? Will this install show all the drive on xpenology.

[Peter Suh]

50 minutes ago, bnokes said:

I have RR and using, will this destroy all that is on my install and everything that I set up with the RR?

 

 

maybe ill try to just add your 3ware some how, think i found one that I tried and didn't see if work. 

 

what is this supports to do? Will this install show all the drive on xpenology.

 

I think it would be meaningless to provide testing support if I only contact you once every two months.