Jump to content
XPEnology Community
  • 0

Jun's DSM 6 Loader - Driver List


Moogs

Question

6 answers to this question

Recommended Posts

  • 0
Where can I find a list of drivers supported in jun's bootloader? Seems the threads have mixed the old loader with the newer jun's loader and I don't feel the drivers are supported on both.

 

Look at the tutorial in my signature. At the end of the OP I have listed the drivers that are included. You wont get any better than that as Jun has not published himself the list. I simply did a service to the community by grouping the posts relevant to the compiled drivers for Jun's loader. FYI some defaults drivers where compiled by Jun. Additional drivers were compiled by Trantor and Arcao.

Link to comment
Share on other sites

  • 0

 

Look at the tutorial in my signature. At the end of the OP I have listed the drivers that are included. You wont get any better than that as Jun has not published himself the list. I simply did a service to the community by grouping the posts relevant to the compiled drivers for Jun's loader. FYI some defaults drivers where compiled by Jun. Additional drivers were compiled by Trantor and Arcao.

 

You're the man Polanskiman!

 

mpt2sas: LSI SAS 6Gb/s Host Adapters SAS2004, SAS2008, SAS2108, SAS2116, SAS2208, SAS2308 and SSS6200

 

Should cover the 2 cards I have.

Link to comment
Share on other sites

  • 0

I haven't checked if those drivers are in the main ramdisk or the extra ramdisk.

 

If they are in the extra ramdisk then you might need to modify the grub file as follows otherwise there is no need.

 

In the gub file change the following line:

initrd $img/ramdisk.lzma $img/$extra_initrd

to:

initrd $img/$extra_initrd $img/ramdisk.lzma

Link to comment
Share on other sites

  • 0
I haven't checked if those drivers are in the main ramdisk or the extra ramdisk.

If they are in the extra ramdisk then you might need to modify the grub file as follows otherwise there is no need.

 

Worked out of the box with the 9205-8e. Good stuff.

Link to comment
Share on other sites

  • 0
On 1/30/2017 at 8:00 PM, Polanskiman said:

I haven't checked if those drivers are in the main ramdisk or the extra ramdisk.

 

If they are in the extra ramdisk then you might need to modify the grub file as follows otherwise there is no need.

 

In the gub file change the following line:

 


initrd $img/ramdisk.lzma $img/$extra_initrd
 

 

to:

 


initrd $img/$extra_initrd $img/ramdisk.lzma
 

 

 

 

i am using ds3617 jun 1.02b works but my sas2008-it does not seem to work i am using the latest firmware is this a firmware issue and if so which version is recommended and if not then what can i do to get this working?

Link to comment
Share on other sites

  • 0

I have downgrade my lsi 9211-it sas2008 from p20 to p19 and i still does not work using jun 1.02b ds3617 6.1.3

 

can someone respond?

 


[    3.119995] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 200                                                         6)
[    3.125607] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    3.142392] Fusion MPT base driver 3.04.20
[    3.142395] Copyright (c) 1999-2008 LSI Corporation
[    3.152978] Fusion MPT SPI Host driver 3.04.20
[    3.158430] Fusion MPT SAS Host driver 3.04.20
[    3.163786] Fusion MPT misc device (ioctl) driver 3.04.20
[    3.163888] mptctl: Registered with Fusion MPT base driver
[    3.163891] mptctl: /dev/mptctl @ (major,minor=10,220)
[    3.174735] megasas: 06.506.00.00-rc1 Sat. Feb. 9 17:00:00 PDT 2013
[    3.180708] mpt2sas version 20.00.00.00 loaded
[    3.180846] scsi6 : Fusion MPT SAS Host
[    3.181255] mpt2sas 0000:08:00.0: enabling device (0000 -> 0002)
[    3.181309] mpt2sas0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (660                                                         51852 kB)
[    3.181321] mpt2sas0: sending diag reset !!
[    3.332476] mpt2sas0: diag reset: FAILED
[    3.332635] mpt2sas0: _base_get_ioc_facts: failed getting to correct state
[    3.332903] mpt2sas0: mpt2sas_base_unmap_resources
[    3.332941] mpt2sas0: Controller resources are already freed
[    3.332943] mpt2sas0: failure at //source/lsi-mpt2sas/mpt2sas_scsih.c:11743/_                                                         scsih_probe()!
[    3.339862] mpt3sas version 13.00.00.00 loaded

 

Edited by medric
updated
Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...