mervincm Posted November 20, 2022 #1 Posted November 20, 2022 I am trying to install Xpenology virtualized via Proxmox. I have attempted to follow a few guides, but have not seemed to find a solution. This one seems to be the most current https://www.youtube.com/watch?v=td1XNHL_gAg&t=330s but I land at thte same issue. When it comes time to install DSM, it sees two disks and it fails to complete. I only add one disk (other than the 1GB boot volume) but it always sees two disks and I assume, it is trying to install DSM on my 1 GBE boot volume thus failing. Note: I have tried the currect .93 version and that wouldnt procees, so I used the .927 version using in the guide ... that got me all the way to DSM installation. This proxmox host is ( so far) dedicated to the DSM, so I can change anything to accomodate. Quote
mervincm Posted November 21, 2022 Author #2 Posted November 21, 2022 (edited) My Hardware is a Lenovo D30 4229 (2x internal NIC, 2x E5-2690,128G, 256GB SSD on systemboard SATA for proxmoxboot/ISO/VM storage, AIC JMS585 SATA, AIC NetXtreme II 10GB ) https://pcsupport.lenovo.com/us/en/products/workstations/thinkstation-d-series-workstations/thinkstation-d30/4229/parts/pd023261-detailed-specifications-and-overview-thinkstation-d30 https://www.amazon.ca/JMT-Expansion-Converter-Backward-Compatible/dp/B07VPVV97Y https://www.ebay.com/itm/IBM-BROADCOM-PCI-EX-10Gb-FIBRE-SERVER-ADAPTER-42C1792-BCM957710A1020G-/351569797201?_ul=IN (both AIC are hopefully to bw passed through to DSM at some point but unused for now) I used DS920 as that was what I found for a most recent guide, but I am wondering if perhaps my hw is too old for the ds 920? under proxmox I didn't think so but ... Lenovo firmware MB SATA all set to hot plug (not sure it matters under proxmox but ..) audio, card reader diskabled (not sure if that would be seem as non attached disk, nor if it mattered under proxmox) virtualization enabled legacy boot enabled (required for proxmox to boot) Proxmox updated to v 7.2.14 DS920 virtual hardware 1 socket,2 core, 2GB,Seabios,default display,default machine,SCSI VirtIO,SATA disk0:1GB TC .927 img, disk1:100GB, net0=vitIO,serial0 bootorder:sata0 I followed the linked guide to install DS920+ using .927 except options to update as that prevented me from proceeding Install DS920+ DSM 7.1.1 Proxmox ./rploader.sh update now (didn't allow this) ./rploader.sh serialgen DS920+ ./rploader.sh ext geminilake-7.1.1-42962 add https://raw.githubusercontent.com/pocopico/redpill-load/master/redpill-virtio/rpext-index.json ./rploader.sh ext geminilake-7.1.1-42962 add https://raw.githubusercontent.com/pocopico/redpill-load/develop/redpill-acpid/rpext-index.json edit user_config_json SataPortMap:4 DiskIdxMap:0 ./rploader.sh backup now ./rploader.sh build geminilake-7.1.1-42962 [ 0.000000] Command line: BOOT_IMAGE=/zImage withefi earlyprintk syno_hw_version=DS920+ console=ttyS0,115200n8 netif_num=1 synoboot2 pid=0xa4a5 earlycon=uart8250,io,0x3f8,115200n8 mac1=001132C95BB3 sn=20C0SBRCH75XG HddEnableDynamicPower=1 vid=0x0525 elevator=elevator loglevel=15 intel_iommu=igfx_off DiskIdxMap=0 vender_format_version=2 log_buf_len=32M root=/dev/md0 SataPortMap=4 syno_ttyS1=serial,0x2f8 syno_ttyS0=serial,0x3f8 [ 1.788548] ahci 0000:00:07.0: AHCI 0001.0000 32 slots 6 ports 1.5 Gbps 0x3f impl SATA mode [ 1.789899] ahci 0000:00:07.0: flags: 64bit ncq only [ 1.790881] Cannot find slot node of this ata_port. [ 1.791800] Cannot find slot node of this ata_port. [ 1.792700] Cannot find slot node of this ata_port. [ 1.793605] Cannot find slot node of this ata_port. [ 1.794534] Cannot find slot node of this ata_port. [ 1.795466] Cannot find slot node of this ata_port. [ 1.868218] scsi host0: ahci [ 1.870565] scsi host1: ahci [ 1.873710] scsi host2: ahci [ 1.876461] scsi host3: ahci [ 1.878967] scsi host4: ahci [ 1.880809] scsi host5: ahci [ 1.881450] ata1 : SATA max UDMA/133 abar m4096@0xfea52000 port 0xfea52100 irq 24 [ 1.882695] ata2 : SATA max UDMA/133 abar m4096@0xfea52000 port 0xfea52180 irq 24 [ 1.883922] ata3 : SATA max UDMA/133 abar m4096@0xfea52000 port 0xfea52200 irq 24 [ 1.885141] ata4 : SATA max UDMA/133 abar m4096@0xfea52000 port 0xfea52280 irq 24 [ 1.886354] ata5 : SATA max UDMA/133 abar m4096@0xfea52000 port 0xfea52300 irq 24 [ 1.887569] ata6 : SATA max UDMA/133 abar m4096@0xfea52000 port 0xfea52380 irq 24 [ 1.888811] ahci: probe of 0001:01:00.0 failed with error -22 [ 2.193288] ata2 : SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.194585] ata2.00 : ATA-7: QEMU HARDDISK, 2.5+, max UDMA/100 [ 2.195547] ata2.00 : 209715200 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 2.196641] ata2.00 : SN:QM00007 [ 2.197188] ata2.00 : applying bridge limits [ 2.198148] ata3 : SATA link down (SStatus 0 SControl 300) [ 2.199062] ata3 : No present pin info for SATA link down event [ 2.200056] Invalid parameter [ 2.200580] ata6 : SATA link down (SStatus 0 SControl 300) [ 2.201494] ata6 : No present pin info for SATA link down event [ 2.202500] Invalid parameter [ 2.203146] ata5 : SATA link down (SStatus 0 SControl 300) [ 2.203991] ata5 : No present pin info for SATA link down event [ 2.204981] Invalid parameter [ 2.205512] ata1 : SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.206840] ata4 : SATA link down (SStatus 0 SControl 300) [ 2.207738] ata4 : No present pin info for SATA link down event [ 2.208715] Invalid parameter [ 2.209230] ata1.00 : ATA-7: QEMU HARDDISK, 2.5+, max UDMA/100 [ 2.210196] ata1.00 : 2097152 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 2.211295] ata1.00 : SN:QM00005 [ 2.211800] ata1.00 : applying bridge limits [ 2.212604] ata2.00 : configured for UDMA/100 [ 2.213331] Invalid parameter [ 2.213864] ata1.00 : configured for UDMA/100 [ 2.214625] Invalid parameter [ 2.215200] ata1.00 : Find SSD disks. [QEMU HARDDISK] [ 2.217159] scsi 0:0:0:0: Direct-Access QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5 [ 2.219138] Cannot find slot node of this ata_port. [ 2.219932] got SATA disk[0] [ 2.220568] ata2.00 : Find SSD disks. [QEMU HARDDISK] [ 2.220688] sd 0:0:0:0: [sata1] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB) [ 2.220907] sd 0:0:0:0: [sata1] Write Protect is off [ 2.220908] sd 0:0:0:0: [sata1] Mode Sense: 00 3a 00 00 [ 2.220973] sd 0:0:0:0: [sata1] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.226304] sata1: p1 p2 p3 [ 2.227403] sd 0:0:0:0: [sata1] Attached SCSI disk [ 2.230750] scsi 1:0:0:0: Direct-Access QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5 [ 2.232384] Cannot find slot node of this ata_port. [ 2.233218] got SATA disk[1] [ 2.233832] sd 1:0:0:0: [sata2] 209715200 512-byte logical blocks: (107 GB/100 GiB) [ 2.235545] sd 1:0:0:0: [sata2] Write Protect is off [ 2.236389] sd 1:0:0:0: [sata2] Mode Sense: 00 3a 00 00 [ 2.237486] sd 1:0:0:0: [sata2] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.240424] sd 1:0:0:0: [sata2] Attached SCSI disk System is booting dtbpatch - early /sys/block/sata1/device/syno_block_info 00:07.0 - 0 /sys/block/sata2/device/syno_block_info 00:07.0 - 1 Most likely your vid/pid configuration is not correct, or you don't have drivers needed for your USB/SATA controller (does this matter if I boot SATA?) [ 32.964417] Fail to get disk 1 led type [ 32.965033] Fail to get disk 2 led type [ 32.965632] Fail to get disk 3 led type [ 32.966244] Fail to get disk 4 led type :: Loading module syno_hddmon ... [FAILED] Excution Error Edited November 21, 2022 by mervincm Quote
mervincm Posted November 21, 2022 Author #3 Posted November 21, 2022 (edited) Edited November 21, 2022 by mervincm Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.