Automated RedPill Loader (ARPL)

kociubin · October 28, 2022

I successfully upgraded my ProxMox installation to Beta2. I simply replaced the existing boot drive with the beta2 image. I booted it up. Re-configured using the same parameters as before. I then rebooted the whole VM and it booted right into DSM (i.e. no migration or repair needed).

Everything worked flawlessly first time around.

Thank you

chiefg · October 28, 2022

Hi all,

I have the following setup, motherboard has two onboard controllers

regular sata 6

SAS 3 4

Then I have two SAS3 controller, each has 8 ports

so 8,8

here is what my SataPortMap will be ----- 6488

here is what my DiskIdxMap will be ----- 050800

All ports will have a drive, is this correct?

Thanks

Captainfingerbang · October 29, 2022

yes I have this same concern .

x99 w/single e5 2680v4 intel nic card.

will the 10 sata ports pose concerns?

Bayview252 · October 29, 2022

Hey, just wanted to say thank you @fbelavenuto. I upgraded / migrated my HP Microserver Gen8 from DSM 6.2 ds3615 / Jun 1.03b to ds3622xs+ DSM 7.1 / ARPL Beta-0.1 with no problems at all. The only manual intervention in the Loader configuration was to add a 2nd Mac address in the config file and change netif_num to "2". Booted up, migrated with DSM_DS3622xs+_42661.pat (with Update 1 included), and had to repair a couple of packages. Magic!

Edited October 29, 2022 by Bayview252
added netif_num

lustigerpeter · October 29, 2022

ARPL Beta2 no updates work.
Update AEPL, check last version, system hangs
Update Modules, Check last version, System hangs

highrulez · October 30, 2022

Hi guys,

I need a little help here. I just updated my loader to ARPL 1.0 beta2. Everything went smoothly except for my USB hard drive which it detects as an internal HDD instead of an external device. How can I fix this?

frezeen · October 30, 2022

On 10/26/2022 at 10:05 PM, frezeen said:

i have a proplem only, how can i set disk in the 4 slots of ds918+?

i have a virtio scsi single, with 2 qemu scsi disks in proxmox VM but DSM call them disk 13 and 14, i want disk 1 and 2 or something in that 4 slots only

solved with: i440fx in proxmox and disks to VM with -sata option and not -scsi.

i have 2 disks in slot 2 and 3 now

frezeen · October 30, 2022

someone have a guide or a way to enable quicksync on a VM proxmox machine created with ARPL loader?

Edited October 30, 2022 by frezeen

nemesis122 · October 30, 2022

Hi all

with the lastest Release i have Kernel Panic and crash with the ixxgbe driver with 0.5 alpha1 it was working pls what has changed to this newest release.?

udhcpc: started, v1.30.1
[  125.065667] ixgbe 0000:07:00.0 eth0: detected SFP+: 3
[  125.090134] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  125.128151] IP: [<ffffffff810b314b>] timecounter_read+0xb/0x50
[  125.156765] PGD 4050a2067 PUD 407b37067 PMD 0
[  125.178358] Oops: 0000 [#1] SMP
[  125.194043] Modules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc atlantic(OE) r8168(OE) be2net(OE) igb(OE) i2c_algo_bit e1000e(OE) vfat fat mdio crc_itu_t crc_ccitt sg loop sha256_generic synorbd(PO) synofsbd(PO) usb_storage button(E) ixgbe(OE) vxlan etxhci_hcd ip6_udp_tunnel udp_tunnel dca xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios]
[  125.378475] CPU: 1 PID: 3929 Comm: kworker/u48:5 Tainted: P           OE   4.4.180+ #42962
[  125.418235] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 11/02/2015
[  125.452080] Workqueue: ixgbe ixgbe_service_task [ixgbe]
[  125.477034] task: ffff8800ed83a640 ti: ffff880407ef8000 task.ti: ffff880407ef8000
[  125.513147] RIP: 0010:[<ffffffff810b314b>]  [<ffffffff810b314b>] timecounter_read+0xb/0x50
[  125.553339] RSP: 0018:ffff880407efbd70  EFLAGS: 00010046
[  125.579295] RAX: 0000000000000293 RBX: ffff8804061d3700 RCX: 0000000000000003
[  125.614880] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000000
[  125.649564] RBP: ffff880407efbd78 R08: 0000000000000001 R09: 0000000000000000
[  125.684158] R10: 0000000000000000 R11: ffff8804061d0c60 R12: ffff8804061d36e0
[  125.718885] R13: 0000000000000293 R14: ffff8804061d3568 R15: ffff8803f3091c00
[  125.753021] FS:  0000000000000000(0000) GS:ffff880409640000(0000) knlGS:0000000000000000
[  125.792173] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  125.820025] CR2: 0000000000000000 CR3: 0000000405a5f000 CR4: 00000000001606f0
[  125.854624] Stack:
[  125.864190]  ffff8804061d07c0 ffff880407efbda0 ffffffffa01a78c4 ffff8804061d07c0
[  125.899330]  ffff8804061d1740 ffff8803f26b3000 ffff880407efbdf8 ffffffffa017fff5
[  125.935226]  0000000000000003 0000000000000000 ffff880407efbde0 00000020ed00a6a0
[  125.971069] Call Trace:
[  125.983217]  [<ffffffffa01a78c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe]
[  126.017134]  [<ffffffffa017fff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe]
[  126.049852]  [<ffffffff810713ba>] worker_run_work+0x9a/0xe0
[  126.076722]  [<ffffffffa017f760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe]
[  126.109760]  [<ffffffff810692fb>] process_one_work+0x1db/0x4e0
[  126.138050]  [<ffffffff8106962d>] worker_thread+0x2d/0x4a0
[  126.165289]  [<ffffffff81069600>] ? process_one_work+0x4e0/0x4e0
[  126.194213]  [<ffffffff8106d9e3>] kthread+0xd3/0xf0
[  126.217762]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  126.247129]  [<ffffffff8156712f>] ret_from_fork+0x3f/0x80
[  126.273469]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  126.302549] Code: 00 00 48 c7 43 20 00 00 00 00 48 d3 e0 48 83 e8 01 48 89 43 18 5b 41 5c 41 5d 5d c3 0f 1f 40 00 55 48 89 e5 53 48 89 fb 48 8b 3f <48> 8b 07 e8 5d 83 4b 00 48 8b 0b 48 89 c2 48 2b 53 08 8b 71 10
[  126.394581] RIP  [<ffffffff810b314b>] timecounter_read+0xb/0x50
[  126.423002]  RSP <ffff880407efbd70>
[  126.439628] CR2: 0000000000000000
[  126.455280] ---[ end trace ecb5c4a8de76b54c ]---
[  126.477608] BUG: unable to handle kernel paging request at ffffffffffffffd8
[  126.511779] IP: [<ffffffff8106de67>] kthread_data+0x7/0x10
[  126.538849] PGD 408a0d067 PUD 408a0f067 PMD 0
[  126.560245] Oops: 0000 [#2] SMP
[  126.575802] Modules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc atlantic(OE) r8168(OE) be2net(OE) igb(OE) i2c_algo_bit e1000e(OE) vfat fat mdio crc_itu_t crc_ccitt sg loop sha256_generic synorbd(PO) synofsbd(PO) usb_storage button(E) ixgbe(OE) vxlan etxhci_hcd ip6_udp_tunnel udp_tunnel dca xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios]
[  126.765589] CPU: 1 PID: 3929 Comm: kworker/u48:5 Tainted: P      D    OE   4.4.180+ #42962
[  126.805311] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 11/02/2015
[  126.840489] task: ffff8800ed83a640 ti: ffff880407ef8000 task.ti: ffff880407ef8000
[  126.877798] RIP: 0010:[<ffffffff8106de67>]  [<ffffffff8106de67>] kthread_data+0x7/0x10
[  126.918547] RSP: 0018:ffff880407efba90  EFLAGS: 00010002
[  126.945738] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000001
[  126.981143] RDX: ffff8803f3008400 RSI: 0000000000000001 RDI: ffff8800ed83a640
[  127.016705] RBP: ffff880407efbaa0 R08: 0000001d72a70afd R09: 000000000000002c
[  127.051867] R10: 0000000000000000 R11: 0000000002ee9800 R12: ffff8800ed83a640
[  127.086431] R13: ffff880409656340 R14: ffff880409656340 R15: 0000000000000001
[  127.121651] FS:  0000000000000000(0000) GS:ffff880409640000(0000) knlGS:0000000000000000
[  127.160811] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  127.188179] CR2: 0000000000000028 CR3: 0000000405a5f000 CR4: 00000000001606f0
[  127.222251] Stack:
[  127.231788]  ffffffff8106a30c 0000000000016340 ffff880407efbaf0 ffffffff81563191
[  127.267809]  0000000007c9a1b0 ffff880407efbae8 ffff8800ed83a640 ffff8800ed83a640
[  127.303621]  ffff880407efbb40 ffff880407efb6f0 ffff8803f3168000 ffffffff81835ea0
[  127.339306] Call Trace:
[  127.350973]  [<ffffffff8106a30c>] ? wq_worker_sleeping+0xc/0x90
[  127.379552]  [<ffffffff81563191>] __schedule+0x471/0x7c0
[  127.405388]  [<ffffffff81563506>] schedule+0x26/0x70
[  127.429244]  [<ffffffff81053b60>] do_exit+0x680/0xa10
[  127.453125]  [<ffffffff81007b95>] oops_end+0x85/0xa0
[  127.477064]  [<ffffffff8103ef7c>] no_context+0x12c/0x1d0
[  127.502564]  [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180
[  127.533482]  [<ffffffff81562ffd>] ? __schedule+0x2dd/0x7c0
[  127.560043]  [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10
[  127.588837]  [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0
[  127.616491]  [<ffffffff8103f74c>] do_page_fault+0xc/0x10
[  127.642716]  [<ffffffff81568b92>] page_fault+0x22/0x30
[  127.667434]  [<ffffffff810b314b>] ? timecounter_read+0xb/0x50
[  127.695152]  [<ffffffffa01a78c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe]
[  127.728732]  [<ffffffffa017fff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe]
[  127.760982]  [<ffffffff810713ba>] worker_run_work+0x9a/0xe0
[  127.787856]  [<ffffffffa017f760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe]
[  127.821265]  [<ffffffff810692fb>] process_one_work+0x1db/0x4e0
[  127.849652]  [<ffffffff8106962d>] worker_thread+0x2d/0x4a0
[  127.876269]  [<ffffffff81069600>] ? process_one_work+0x4e0/0x4e0
[  127.904879]  [<ffffffff8106d9e3>] kthread+0xd3/0xf0
[  127.928484]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  127.957726]  [<ffffffff8156712f>] ret_from_fork+0x3f/0x80
[  127.983252]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  128.012144] Code: 89 de e8 6d d6 4f 00 49 8b 04 24 48 85 c0 75 e6 e9 07 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 8b 87 c8 04 00 00 <48> 8b 40 d8 c3 0f 1f 40 00 55 ba 08 00 00 00 48 89 e5 48 83 ec
[  128.104850] RIP  [<ffffffff8106de67>] kthread_data+0x7/0x10
[  128.132382]  RSP <ffff880407efba90>
[  128.149022] CR2: ffffffffffffffd8
[  128.165183] ---[ end trace ecb5c4a8de76b54d ]---
[  128.187765] Fixing recursive fault but reboot is needed!

i can deselecct the driver then the server is not found and when i selectt the ixgbe driver it has en buffer overflow.

Here is the log

125.983217] [<ffffffffa01a78c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe]

thank you

Captainfingerbang · October 30, 2022

On 7/4/2022 at 7:10 AM, fbelavenuto said:

Hi, it's not bug. All supported models have the e1000e module natively. The loader didn't find any other modules needed in your case.
The e1000e module exists for any future model that does not have it. ACPId is not installed automatically, when I confirm that it works in any situation I will put it to be installed automatically.

Ah, I forget to answer your second question, sorry. You can update up to 42661 update5 which is the latest at this time. No need to turn off internet access.

On 10/28/2022 at 4:55 PM, chiefg said:

so thank you for your contributions I am so happy and amazed and grateful for this but one thing is really really bothering me..

I cannot find an explanation for why you say you should use an SSD for the Loader?

I have tons of extra ssds laying around, but what is the purpose or how does the SSD benefit the loader speed or what is it that it benefits?

Because with June's loader I don't recall it made a difference whether you use a slow drive or fast

Edited October 30, 2022 by Captainfingerbang

RedwinX · October 30, 2022

On 10/28/2022 at 7:42 AM, Mincemeat said:

Thanks for bringing that to out attention. We will get right on it, making loaders harder to work and whatever

Why u in their dms, you got a legit unit?

We have a lot of Synology RS version in my company, with warranty extension. I just tried to use it to get the kernel sources lol, for the community

Valiran34 · October 30, 2022

Hello!

Is there a way to trick the network connexion? My ds2422 is stuck at 1000Mbps but my network card is a 5Gbps

fbelavenuto · October 31, 2022

On 10/28/2022 at 7:54 AM, jurgenautt said:

Hello, I report that the beta version does not work with my hardware, instead the alpha version v0.5-alpha1 does work correctly (removing some errors that I had previously reported)
the version i try rs4021xs+
If you need to carry out any additional tests, tell me fbelavenuto, thank you very much for the work

.I proceed in the same way, I format a new USB, I install the image, I carry out the configuration process, everything seems correct, I restart to be able to install the dsm, on the screen everything appears correct, (search ip etc, booting etc)
but the windows explorer gives it the ip, but it does nothing, i search with an ip scanner program, but that ip that the loader gives me is not there, as if it did not give the ip or that the drivers of the network cards did not they were fine...

What is your network card model?

fbelavenuto · October 31, 2022

On 10/29/2022 at 4:29 PM, lustigerpeter said:

ARPL Beta2 no updates work.
Update AEPL, check last version, system hangs
Update Modules, Check last version, System hangs

Thanks for the report, I'll make more tests.

fbelavenuto · October 31, 2022

On 10/30/2022 at 11:13 AM, nemesis122 said:

Hi all

with the lastest Release i have Kernel Panic and crash with the ixxgbe driver with 0.5 alpha1 it was working pls what has changed to this newest release.?

udhcpc: started, v1.30.1
[  125.065667] ixgbe 0000:07:00.0 eth0: detected SFP+: 3
[  125.090134] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  125.128151] IP: [<ffffffff810b314b>] timecounter_read+0xb/0x50
[  125.156765] PGD 4050a2067 PUD 407b37067 PMD 0
[  125.178358] Oops: 0000 [#1] SMP
[  125.194043] Modules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc atlantic(OE) r8168(OE) be2net(OE) igb(OE) i2c_algo_bit e1000e(OE) vfat fat mdio crc_itu_t crc_ccitt sg loop sha256_generic synorbd(PO) synofsbd(PO) usb_storage button(E) ixgbe(OE) vxlan etxhci_hcd ip6_udp_tunnel udp_tunnel dca xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios]
[  125.378475] CPU: 1 PID: 3929 Comm: kworker/u48:5 Tainted: P           OE   4.4.180+ #42962
[  125.418235] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 11/02/2015
[  125.452080] Workqueue: ixgbe ixgbe_service_task [ixgbe]
[  125.477034] task: ffff8800ed83a640 ti: ffff880407ef8000 task.ti: ffff880407ef8000
[  125.513147] RIP: 0010:[<ffffffff810b314b>]  [<ffffffff810b314b>] timecounter_read+0xb/0x50
[  125.553339] RSP: 0018:ffff880407efbd70  EFLAGS: 00010046
[  125.579295] RAX: 0000000000000293 RBX: ffff8804061d3700 RCX: 0000000000000003
[  125.614880] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000000
[  125.649564] RBP: ffff880407efbd78 R08: 0000000000000001 R09: 0000000000000000
[  125.684158] R10: 0000000000000000 R11: ffff8804061d0c60 R12: ffff8804061d36e0
[  125.718885] R13: 0000000000000293 R14: ffff8804061d3568 R15: ffff8803f3091c00
[  125.753021] FS:  0000000000000000(0000) GS:ffff880409640000(0000) knlGS:0000000000000000
[  125.792173] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  125.820025] CR2: 0000000000000000 CR3: 0000000405a5f000 CR4: 00000000001606f0
[  125.854624] Stack:
[  125.864190]  ffff8804061d07c0 ffff880407efbda0 ffffffffa01a78c4 ffff8804061d07c0
[  125.899330]  ffff8804061d1740 ffff8803f26b3000 ffff880407efbdf8 ffffffffa017fff5
[  125.935226]  0000000000000003 0000000000000000 ffff880407efbde0 00000020ed00a6a0
[  125.971069] Call Trace:
[  125.983217]  [<ffffffffa01a78c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe]
[  126.017134]  [<ffffffffa017fff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe]
[  126.049852]  [<ffffffff810713ba>] worker_run_work+0x9a/0xe0
[  126.076722]  [<ffffffffa017f760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe]
[  126.109760]  [<ffffffff810692fb>] process_one_work+0x1db/0x4e0
[  126.138050]  [<ffffffff8106962d>] worker_thread+0x2d/0x4a0
[  126.165289]  [<ffffffff81069600>] ? process_one_work+0x4e0/0x4e0
[  126.194213]  [<ffffffff8106d9e3>] kthread+0xd3/0xf0
[  126.217762]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  126.247129]  [<ffffffff8156712f>] ret_from_fork+0x3f/0x80
[  126.273469]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  126.302549] Code: 00 00 48 c7 43 20 00 00 00 00 48 d3 e0 48 83 e8 01 48 89 43 18 5b 41 5c 41 5d 5d c3 0f 1f 40 00 55 48 89 e5 53 48 89 fb 48 8b 3f <48> 8b 07 e8 5d 83 4b 00 48 8b 0b 48 89 c2 48 2b 53 08 8b 71 10
[  126.394581] RIP  [<ffffffff810b314b>] timecounter_read+0xb/0x50
[  126.423002]  RSP <ffff880407efbd70>
[  126.439628] CR2: 0000000000000000
[  126.455280] ---[ end trace ecb5c4a8de76b54c ]---
[  126.477608] BUG: unable to handle kernel paging request at ffffffffffffffd8
[  126.511779] IP: [<ffffffff8106de67>] kthread_data+0x7/0x10
[  126.538849] PGD 408a0d067 PUD 408a0f067 PMD 0
[  126.560245] Oops: 0000 [#2] SMP
[  126.575802] Modules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc atlantic(OE) r8168(OE) be2net(OE) igb(OE) i2c_algo_bit e1000e(OE) vfat fat mdio crc_itu_t crc_ccitt sg loop sha256_generic synorbd(PO) synofsbd(PO) usb_storage button(E) ixgbe(OE) vxlan etxhci_hcd ip6_udp_tunnel udp_tunnel dca xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios]
[  126.765589] CPU: 1 PID: 3929 Comm: kworker/u48:5 Tainted: P      D    OE   4.4.180+ #42962
[  126.805311] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 11/02/2015
[  126.840489] task: ffff8800ed83a640 ti: ffff880407ef8000 task.ti: ffff880407ef8000
[  126.877798] RIP: 0010:[<ffffffff8106de67>]  [<ffffffff8106de67>] kthread_data+0x7/0x10
[  126.918547] RSP: 0018:ffff880407efba90  EFLAGS: 00010002
[  126.945738] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000001
[  126.981143] RDX: ffff8803f3008400 RSI: 0000000000000001 RDI: ffff8800ed83a640
[  127.016705] RBP: ffff880407efbaa0 R08: 0000001d72a70afd R09: 000000000000002c
[  127.051867] R10: 0000000000000000 R11: 0000000002ee9800 R12: ffff8800ed83a640
[  127.086431] R13: ffff880409656340 R14: ffff880409656340 R15: 0000000000000001
[  127.121651] FS:  0000000000000000(0000) GS:ffff880409640000(0000) knlGS:0000000000000000
[  127.160811] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  127.188179] CR2: 0000000000000028 CR3: 0000000405a5f000 CR4: 00000000001606f0
[  127.222251] Stack:
[  127.231788]  ffffffff8106a30c 0000000000016340 ffff880407efbaf0 ffffffff81563191
[  127.267809]  0000000007c9a1b0 ffff880407efbae8 ffff8800ed83a640 ffff8800ed83a640
[  127.303621]  ffff880407efbb40 ffff880407efb6f0 ffff8803f3168000 ffffffff81835ea0
[  127.339306] Call Trace:
[  127.350973]  [<ffffffff8106a30c>] ? wq_worker_sleeping+0xc/0x90
[  127.379552]  [<ffffffff81563191>] __schedule+0x471/0x7c0
[  127.405388]  [<ffffffff81563506>] schedule+0x26/0x70
[  127.429244]  [<ffffffff81053b60>] do_exit+0x680/0xa10
[  127.453125]  [<ffffffff81007b95>] oops_end+0x85/0xa0
[  127.477064]  [<ffffffff8103ef7c>] no_context+0x12c/0x1d0
[  127.502564]  [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180
[  127.533482]  [<ffffffff81562ffd>] ? __schedule+0x2dd/0x7c0
[  127.560043]  [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10
[  127.588837]  [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0
[  127.616491]  [<ffffffff8103f74c>] do_page_fault+0xc/0x10
[  127.642716]  [<ffffffff81568b92>] page_fault+0x22/0x30
[  127.667434]  [<ffffffff810b314b>] ? timecounter_read+0xb/0x50
[  127.695152]  [<ffffffffa01a78c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe]
[  127.728732]  [<ffffffffa017fff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe]
[  127.760982]  [<ffffffff810713ba>] worker_run_work+0x9a/0xe0
[  127.787856]  [<ffffffffa017f760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe]
[  127.821265]  [<ffffffff810692fb>] process_one_work+0x1db/0x4e0
[  127.849652]  [<ffffffff8106962d>] worker_thread+0x2d/0x4a0
[  127.876269]  [<ffffffff81069600>] ? process_one_work+0x4e0/0x4e0
[  127.904879]  [<ffffffff8106d9e3>] kthread+0xd3/0xf0
[  127.928484]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  127.957726]  [<ffffffff8156712f>] ret_from_fork+0x3f/0x80
[  127.983252]  [<ffffffff8106d910>] ? kthread_worker_fn+0x160/0x160
[  128.012144] Code: 89 de e8 6d d6 4f 00 49 8b 04 24 48 85 c0 75 e6 e9 07 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 8b 87 c8 04 00 00 <48> 8b 40 d8 c3 0f 1f 40 00 55 ba 08 00 00 00 48 89 e5 48 83 ec
[  128.104850] RIP  [<ffffffff8106de67>] kthread_data+0x7/0x10
[  128.132382]  RSP <ffff880407efba90>
[  128.149022] CR2: ffffffffffffffd8
[  128.165183] ---[ end trace ecb5c4a8de76b54d ]---
[  128.187765] Fixing recursive fault but reboot is needed!

i can deselecct the driver then the server is not found and when i selectt the ixgbe driver it has en buffer overflow.

Here is the log

125.983217] [<ffffffffa01a78c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe]

thank you

Please update modules, rebuild the loader and test it

fbelavenuto · October 31, 2022

21 hours ago, Captainfingerbang said:

cannot find an explanation for why you say you should use an SSD for the Loader?

Some users have experienced an excessively long time to boot. I recommended using SSD for this reason. If the boot is fast via USB, no SSD is needed.
I'll modify the README to make this clearer.

Thanks.

fbelavenuto · October 31, 2022

16 hours ago, Valiran34 said:

Hello!

Is there a way to trick the network connexion? My ds2422 is stuck at 1000Mbps but my network card is a 5Gbps

What is your network card model?

nemesis122 · October 31, 2022

23 minutes ago, fbelavenuto said:

Please update modules, rebuild the loader and test it

Hi fbelavenuto thank you very much i will do it after work let you know.

Valiran34 · October 31, 2022

il y a 42 minutes, fbelavenuto a dit :

What is your network card model?

I have choices (my DSM is virtualized under Unraid):

- virtio-net

- virtio

- e1000

- vmxnet3 (the one I've choosen)

nemesis122 · October 31, 2022

Hi fbelavenuto

format the usb stick downloaded again rebuild the usb stick complete new --> it was not working same issue

then i have updated all modules and addons with the new usb stick then all is working.:-)

sorry the dumb question but for building the loader i have to everytime update the addons and the modules or when is the changed driver in arpl image avilable ?

anyway thank you very much very much it is working

Michael

and for interesse what is changed that it is working now ?

chiefg · October 31, 2022

I have the same issue with an Intel X540-T2 10gb nic, it used to work until beta came out.

Now if it's installed neither beta works, when I remove it and use the onboard 1gb card the beta loads and works ok

with the 10gb after it boots it shows "ERROR" in red next to IP

CyberBOG · October 31, 2022

Hi there

to everyone .....

I have being tying to get this to work for me but everything goes fine until i have to search or it with Synology Assistant

it does note find the device

but i get a IP address on loader screen 192.168.0.184------- but find my Synology come up no device found

tried using DS3516xs and DS920+ but nothing changes

any ideas why -----

i have had it working with Jun`s Loader and every thing was 100%

please help

Captainfingerbang · October 31, 2022

so my 540's cause some weird things happen to both my test machines currently. I've been trying to take it easy when moving data though. Using only one cord between the two. I've been getting roughly for 400-500 sustained with dips to lowest of 175 then back up.

But this isn't the problem.... and I'm sorry I can't put my specific finger on what the exact problem is. But I do know recently after using the x540s I've had to reinstall DSM because of freezing and other weird stuff. If I take it easy with them I can get them to work solid 25% of the time.The other 75% I assumed was because they weren't compatible or didn't have drivers yet, or because I only named one IP address in my config. I just got a couple of quantia Marvel aqc107 10g cards today so I'm going to be messing with them on v1 or v1 beta or whatever it's called the newest one.

II'm actually kind of stoked because tonight I think I'm going to build that 1622 NVR with some easy Parts real fast and the cameras are already installed. What interests me is using my 918 to maybe manage the NVR via CMS . Before I only had two 918s so I had to connect them via CMS just to get four cameras. Now they'll be way more cameras to test

ngucy5767 · November 1, 2022

10 hours ago, CyberBOG said:

Hi there

to everyone .....

I have being tying to get this to work for me but everything goes fine until i have to search or it with Synology Assistant

it does note find the device

but i get a IP address on loader screen 192.168.0.184------- but find my Synology come up no device found

tried using DS3516xs and DS920+ but nothing changes

any ideas why -----

i have had it working with Jun`s Loader and every thing was 100%

please help

Can login to your router & check your dhcp server ip.

htanh034 · November 1, 2022

I'm upgrading arpl 0.4-alpha12 to v1.0-beta2 with an error below. how do fix it, tks!

Automated RedPill Loader (ARPL)

Recommended Posts

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Join the conversation