Jump to content
XPEnology Community

DSM 7.1-42661 Update 3


Message added by Polanskiman,

Please read the READ ME topic before posting:

 

Recommended Posts

1459227357_2022-07-059_17_19.thumb.png.98094b73900c1f27737c0add35bee6c8.png

 

https://www.synology.com/en-global/releaseNote/DSM?model=DS3622xs%2B

 

Spoiler

Version: 7.1-42661 Update 3

 

(2022-07-05)

Important notes

  1. Your Synology NAS may not notify you of this DSM update because of the following reasons. If you want to update your DSM to this version now, please click here to manually update it. Only Synology NAS with DSM 7.1 installed can be updated to this version.
    • The update is not available in your region yet. The update is expected to be available for all regions within the next few days, although the time of release in each region may vary slightly.
    • Your DSM is working fine without having to update. The system evaluates service statuses and system settings to determine whether it needs to update to this version.
  2. This update will restart your Synology NAS.

Fixed Issues

  1. Fixed an unexpected issue that may occur when users Safe Ejected a single-volume storage pool that was created on DSM 6.2.4 or earlier.
  2. Fixed an issue where certain packages couldn't function properly shortly after restarting DSM.
  3. Fixed an unexpected issue that may occur when users tried to repair degraded storage pools that were previously migrated from a different version of DSM.

 

  • Thanks 1
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 7.1-42661 Update 2
- Loader version and model: Yet Another Jun`s Mod x RedPill DS2422+ v7.0.1-42218
- Using custom extra.lzma: NO
- Installation type: BAREMETAL – Lenovo ThinkCentre Edge71 Intel i3 2120

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - Point of View ION ATOM 330

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.9.0.2 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HP GEN8 MICROSERVER, Xeon E3 1220v2

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

 

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
Link to comment
Share on other sites

1. Backup Server

Outcome of the update: SUCCESSFUL

DSM version prior update:  DSM 7.1-42661 (DS918+) Update1

Loader version and model: tinycore-redpill-uefi.v0.8.0.0.img, DSM 7.1-42661 (DS918+)

Installation type: Baremetal ASRock J4105-ITX, 8 GB RAM, 3x SATA drives

 

1. Production Server

Outcome of the update: SUCCESSFUL 

DSM version prior update:  DSM 7.1-42661 (DS918+) Update1

Loader version and model: tinycore-redpill-uefi.v0.8.0.0.img, DSM 7.1-42661 (DS918+)

Installation type: Baremetal ASRock J4105-ITX, 16 GB RAM, 3x SATA drives

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.9.0.8 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: VMware ESXi 7.0 update 3 @ HPE Microserver Gen8
- Additional comments: VM has a Dell H200 (flashed as LSI in IT mode) in passthough.

 

After the update, on first reboot to avoid recovery mode loop, just boot in TC and run update/postupdate, it will detect the new freshly patch, then reboot normally in dsm.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 7.1-42661 Update 2
- Loader version and model: Tinycore-Redpill, Yet Another Jun`s Mod x RedPill DS3622xs+ v7.0.1-42218
- Using custom extra.lzma: NO
- Installation type: BAREMETAL – ASUS IOT H310i-IM-A R2.0

- Additional comments: Dell Perc H310 (flashed as LSI in IT mode)

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 7.1-42661 Update 1
- Loader version and model: Automated redpill loader DVA1622 v7.1-42661
- Using custom extra.lzma: NO
- Installation type: BAREMETAL – LENOVO THINKCENTRE EDGE 71 INTEL I3 2120

- Additional comments: Works vga out with monitor

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.9.0.2 - DS918+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

./rploader.sh update
sudo ./rploader.sh postupdate apollolake-7.1.0-42661
exitcheck.sh reboot

Transcoding is still working:

cat /usr/syno/etc/codec/activation.conf
{"success":true,"activated_codec":["hevc_dec","ac3_dec","h264_dec","h264_enc","aac_dec","aac_enc","mpeg4part2_dec","vc1_dec","vc1_enc"],"token":"12345678XXXXXXXXX"}

 

Edited by DsMan
  • Thanks 2
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1-42661 Update 3

- Loader version and model:  Automated Redpill Loader

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Supermicro X10SDV-TLN4F, LSI SAS2008

- Additional comments:  Upgraded via GUI

 

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 3
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HPE MicroServer Gen10 Plus

- step 1: Upgraded to DSM 7.1.0-42661u3 via GUI

- After Step 1 update, booted into TCRP and run:

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
  • Like 1
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HP GEN8 MICROSERVER, Xeon E3 1220v2

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

 

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
  • Like 1
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: tinycore-redpill-uefi.v0.8.0.0 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: Baremetal - Gigabyte H370N-WiFi, Pentium G5400, 16 GB Memory DDR4. 
- Additional comments: Intel 82579 PCI-e Dual NIC detected using e1000e along with onboard Intel I211 and I219-V(7) NICs.
  MTU Value: Only 1500 is available as maximum for all 4 NICs. Looking for option to enable 9000. 

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - ASRock C2750D4I

 Additional comments:

   - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

   - Booted into TCRP and run:

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3615xs
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HPE MicroServer Gen7 [N54L]

- step 1: Upgraded to DSM 7.1.0-42661u3 via GUI

- After Step 1 update, booted into TCRP and run:

./rploader.sh update
sudo ./rploader.sh postupdate bromolow-7.1.0-42661
exitcheck.sh reboot

- Additional comments: Dell Perc H310 (flashed as LSI in IT mode)

7x HDD [1SSD+6SAS], Onboard Nic - Enabled, C1E - Disabled, ACPI - v3.0

 

Edited by WDCluB
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 1
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - THECUS N4200ECO and QNAP TS-453A

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: 

   brandnew install DSM7.0.1-42218 
- Loader version and model: 

   tossp/redpill-tool-chain 7.0.1-42218 - DS3622xs+
- Using custom extra.lzma: NO 


- Installation type: BAREMETAL

   Supermicro X11 SSH-LN4F

   E3-1260L v5

   Samsung udimm ECC 16G

 

- Step :

   1st install 7.0.1-42218

   2nd updated to 7.1.0-42661-up1/up2/up3 via GUI

 

- Additional comments: 

  16G MLC usb = synoboot

  SSD Intel S3710 100G = software and docker

  2TBx4 Raid5 = PT download

  5TBx1 = files 

  2TBx2 Raid1 = most important files backup

                                         

 

Edited by spld
Link to comment
Share on other sites

- Outcome of the update: UNSUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 1
- Loader version and model: Tinycore-Redpill v7.1.0 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - MSI 6741 AMD

 

  - Tried to Upgrade to DSM 7.1.0-42661 Update 3 via GUI.  Couldn't get past the manual update.  Got an error pop-up "failed to update file.  File is probably corrupted."

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: 
   fresh install DSM 7.0.1 42218-1 
- Loader version and model: 
   TCRP 0.8.0.0 UEFI - DS3622xs+
- Using custom extra.lzma: NO 

- Installation type: BAREMETAL - Asus X99 "Xeon E5-2678"
   
 - Steps :
   Fresh/clean install TCRP 0.8.0.0 UEFI "7.0.1-42218" (USB-DOM Apacer 1GB)
   
   Update via DSM GUI 42218-1 > 42661-1
   1st update with +300MB package
   
   Synoboot updated with ARPL Loader v0.2-Alpha-3
   Incremental update via DSM GUI from 42661-2 > 42661-3

 

  after reboot ARPL Loader patched Synoboot zImage & RamDisk   

 
- Specs: 
  1G USB DOM Apacer = Synoboot

 

  RAID-10 with 4x 3TB WD REDs (+1 3TB Directly Attached SPARE DRIVE)
  2x WD Green NVME's "R/W" Cache
  
  RAID-10 4x 2TB Seagate NAS Ironwolfs 
  1x 970 EVO NVME "R/O" Cache

Edited by falheiros
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HP GEN8 MICROSERVER, Xeon E3 1270v2

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

 

./rploader.sh update
sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
  • Like 1
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DVA3221
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - QNAP TS-469 PRO

- Note: Updated with standard TCRP update procedure by running postupdate command after applying the update from DSM.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 Update 2
- Loader version and model: Tinycore-Redpill v0.8.0.3 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - QNAP

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

 

./rploader.sh update now
./rploader.sh fullupgrade now
./rploader.sh backup
./rploader.sh postupdate broadwellnk-7.1.0-42661
reboot
Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1.0-42661 
- Loader version and model: Tinycore-Redpill v0.8.0.5 - DS3622xs+
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - N54L

 

  - Upgraded to DSM 7.1.0-42661 Update 3 via GUI

  - Booted into TCRP and run:

 

./rploader.sh update now
./rploader.sh fullupgrade now
./rploader.sh backup
./rploader.sh postupdate broadwellnk-7.1.0-42661
exitcheck.sh reboot
Link to comment
Share on other sites

-Outcome of the update: SUCCESSFUL

-DSM version prior update:  DSM 7.1-42661 (DS918+) Update1

-Loader version and model: tinycore-redpill-uefi.v0.8.0.0.img, DSM 7.1-42661 (DS918+)

-Installation type: Baremetal ASRock J4105-ITX, 8 GB RAM, 4x SATA drives

 

Migrate DSM 6.2.3-25426 (DS918+) Update 2 to DSM 7.1-42661 (DS918+) Update1

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 7.1-42661 Update 3

- Loader version and model:  Automated Redpill Loader

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Gigabyte GA-H81M-S1, ASMEDIA 1061

- Additional comments:  Upgraded via GUI

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...